Page 31 / 320 Scroll up to view Page 26 - 30
Chapter 3 Internet / Wireless Setup Wizard
AMG1302/AMG1202-TSeries User’s Guide
31
The following table describes the fields in this screen.
Note: Virtual Path Identifier (VPI) and Virtual Channel Identifier (VCI) define a virtual circuit.
Figure 10
Internet Connection with ENET ENCAP
Table 3
Internet Access Wizard Setup: IPoA Configuration
LABEL
DESCRIPTION
Encapsulation
Select the encapsulation type your ISP uses from the
Encapsulation
drop-down list box:
IPoA
,
ENET ENCAP
,
PPPoA
, or
PPPoE
.
Multiplex
Select the multiplexing method used by your ISP from the
Multiplex
drop-down list box either VC-based or LLC-based.
VPI
Enter the Virtual Path Identifier (VPI) assigned to you. This field may
already be configured.
VCI
Enter the Virtual Channel Identifier (VCI) assigned to you. This field may
already be configured.
IP Address
Enter the IP address of the AMG1302/AMG1202-TSeries.
Default
Gateway
Enter the default gateway of the ZyXEL Device.
Primary DNS
Server
Enter the primary DNS server IP address for the AMG1302/AMG1202-
TSeries.
Secondary
DNS Server
Enter the secondary DNS server IP address for the AMG1302/AMG1202-
TSeries.
Back
Click this to return to the previous screen without saving.
Next
Click this to continue to the next wizard screen. The next wizard screen
you see depends on what protocol you chose above.
Exit
Click this to close the wizard screen without saving.
Page 32 / 320
Chapter 3 Internet / Wireless Setup Wizard
AMG1302/AMG1202-TSeries User’s Guide
32
The following table describes the fields in this screen.
Table 4
Internet Connection with ENET ENCAP
LABEL
DESCRIPTION
Encapsulation
Select the encapsulation type your ISP uses from the
Encapsulation
drop-down list box:
IPoA
,
ENET ENCAP
,
PPPoA
, or
PPPoE
.
Multiplex
Select the multiplexing method used by your ISP from the
Multiplex
drop-down list box either VC-based or LLC-based.
VPI
Enter the Virtual Path Identifier (VPI) assigned to you. This field may
already be configured.
VCI
Enter the Virtual Channel Identifier (VCI) assigned to you. This field may
already be configured.
Select
Yes
to enter specific IP information from your Internet service provider.
Enter
your Internet access information exactly as your service provider gave it to you.
IP Address
Enter the IP address of the AMG1302/AMG1202-TSeries.
Subnet Mask
Enter the subnet mask in dotted decimal notation.
Refer to the appendix
to calculate a subnet mask if you are implementing
subnetting.
Default
Gateway
You must specify a gateway IP address (supplied by your ISP) when you
use
ENET ENCAP
in the
Encapsulation
field in the previous screen.
Primary DNS
Server
Enter the primary DNS server IP address for the AMG1302/AMG1202-
TSeries.
Secondary
DNS Server
Enter the secondary DNS server IP address for the AMG1302/AMG1202-
TSeries.
Back
Click this to return to the previous screen without saving.
Apply
Click this to save your changes.
Exit
Click this to close the wizard screen without saving.
Page 33 / 320
Chapter 3 Internet / Wireless Setup Wizard
AMG1302/AMG1202-TSeries User’s Guide
33
Figure 11
Internet Connection with PPPoA
The following table describes the fields in this screen.
Table 5
Internet Connection with PPPoA
LABEL
DESCRIPTION
Encapsulation
Select the encapsulation type your ISP uses from the
Encapsulation
drop-down list box:
IPoA
,
ENET ENCAP
,
PPPoA
, or
PPPoE
.
User Name
Enter the login name that your ISP gives you.
Password
Enter the password associated with the user name above.
Multiplex
Select the multiplexing method used by your ISP from the
Multiplex
drop-down list box either VC-based or LLC-based.
VPI
Enter the Virtual Path Identifier (VPI) assigned to you. This field may
already be configured.
VCI
Enter the Virtual Channel Identifier (VCI) assigned to you. This field may
already be configured.
IP Address
Enter the IP address of the AMG1302/AMG1202-TSeries.
Primary DNS
Server
Enter the primary DNS server IP address for the AMG1302/AMG1202-
TSeries.
Secondary
DNS Server
Enter the secondary DNS server IP address for the AMG1302/AMG1202-
TSeries.
Back
Click this to return to the previous screen without saving.
Apply
Click this to save your changes.
Exit
Click this to close the wizard screen without saving.
Page 34 / 320
Chapter 3 Internet / Wireless Setup Wizard
AMG1302/AMG1202-TSeries User’s Guide
34
Figure 12
Internet Connection with PPPoE
The following table describes the fields in this screen.
If the user name and/or password you entered for PPPoE or PPPoA connection are not
correct, you are prompted to enter the correct information.
Table 6
Internet Connection with PPPoE
LABEL
DESCRIPTION
User Name
Enter the user name exactly as your ISP assigned. If assigned a name in
the form user@domain where domain identifies a service name, then enter
both components exactly as given.
Password
Enter the password associated with the user name above.
Multiplex
Select the multiplexing method used by your ISP from the
Multiplex
drop-
down list box either VC-based or LLC-based.
VPI
Enter the Virtual Path Identifier (VPI) assigned to you. This field may
already be configured.
VCI
Enter the Virtual Channel Identifier (VCI) assigned to you. This field may
already be configured.
Select
Yes
to enter specific IP information from your Internet service provider.
Enter
your Internet access information exactly as your service provider gave it to you.
IP Address
Enter the IP address of the AMG1302/AMG1202-TSeries.
Primary DNS
Server
Enter the primary DNS server IP address for the AMG1302/AMG1202-
TSeries.
Secondary
DNS Server
Enter the secondary DNS server IP address for the AMG1302/AMG1202-
TSeries.
Back
Click this to return to the previous screen without saving.
Apply
Click this to save your changes.
Exit
Click this to close the wizard screen without saving.
Page 35 / 320
Chapter 3 Internet / Wireless Setup Wizard
AMG1302/AMG1202-TSeries User’s Guide
35
If the Internet connection fails, check to see if your account is activated.
After you configure the Internet access information, use the following screen to set up
your wireless LAN.
5
Check the
Wireless Service
box to enable wireless connection on the ZyXEL device.
6
Configure your wireless settings in this screen. Click
Next
.
Figure 13
Wireless Setup
The following table describes the labels in this screen.
Table 7
Wireless Setup
LABEL
DESCRIPTION
Wireless
Service
Click this to enable or disable wireless service on the ZyXEL device.
Wireless
Network
Name(SSID)
Enter a descriptive name (up to 32 printable 7-bit ASCII characters) for the
wireless LAN.
If you change this field on the AMG1302/AMG1202-TSeries, make sure all
wireless stations use the same SSID in order to access the network.
Channel
Selection
The range of radio frequencies used by IEEE 802.11b/g wireless devices is
called a channel. Select a channel ID that is not already in use by a
neighboring device.
Security
Displays the security setting. To mofidy, see
Section 7.2 on page 92
.
Pre-Shared
Key
Enter a set of characters (8 to 63 characters or 64 hexadecimal digits [a-f,
A-F, and 0-9]) for the shared security key.
Back
Click this to return to the previous screen without saving.
Next
Click this to continue to the next wizard screen.
Exit
Click this to close the wizard screen without saving.

Rate

3.7 / 5 based on 3 votes.

Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top