Page 16 / 320 Scroll up to view Page 11 - 15
Chapter 1 Introduction
AMG1302/AMG1202-TSeries User’s Guide
16
1.4
Applications for the AMG1302/AMG1202-TSeries
Here are some example uses for which the AMG1302/AMG1202-TSeries is well suited.
1.4.1
Internet Access
Your AMG1302/AMG1202-TSeries provides shared Internet access by connecting the DSL port to
the
DSL
or
MODEM
jack on a splitter or your telephone jack. Computers can connect to the
AMG1302/AMG1202-TSeries’s Ethernet ports (or wirelessly).
Figure 1
AMG1302/AMG1202-TSeries’s Router Features
You can also configure firewall and filtering feature on the AMG1302/AMG1202-TSeries for secure
Internet access. When the firewall is on, all incoming traffic from the Internet to your network is
blocked unless it is initiated from your network. This means that probes from the outside to your
network are not allowed, but you can safely browse the Internet and download files.
Use the filtering feature to block access to specific web sites or Internet applications such as MSN or
Yahoo Messenger. You can also configure IP/MAC filtering rules for incoming or outgoing traffic.
Use QoS to efficiently manage traffic on your network by giving priority to certain types of traffic
and/or to particular computers. For example, you could make sure that the AMG1302/AMG1202-
TSeries gives voice over Internet calls high priority, and/or limit bandwidth devoted to the boss’s
excessive file downloading.
1.4.2
Wireless Access
The ZyXEL Device is a wireless Access Point (AP) for IEEE 802.11b/g/n compliant clients, such as
notebook computers or PDAs and iPads. It allows them to connect to the Internet without having to
rely on inconvenient Ethernet cables. You can set up a wireless network with WPS (WiFi Protected
Setup) or manually add a client to your wireless network.
DSL
LAN
WAN
Page 17 / 320
Chapter 1 Introduction
AMG1302/AMG1202-TSeries User’s Guide
17
Figure 2
Wireless Access Example
1.5
General Hardware Features
Figure 3
General Hardware Features
The following table describes the LEDs..
Table 1
LED Descriptions
LED
COLOR
STATUS
DESCRIPTION
(POWER)
Green
On
The AMG1302/AMG1202-TSeries is receiving power and ready for
use.
Blinking
The AMG1302/AMG1202-TSeries is self-testing.
Red
On
The AMG1302/AMG1202-TSeries detected an error while self-
testing, or there is a device malfunction.
Off
The AMG1302/AMG1202-TSeries is not receiving power.
Ethernet 1-4
Green
On
The AMG1302/AMG1202-TSeries has an Ethernet connection with
a device on the Local Area Network (LAN).
Blinking
The AMG1302/AMG1202-TSeries is sending/receiving data to /
from the LAN.
Off
The AMG1302/AMG1202-TSeries does not have an Ethernet
connection with the LAN.
Page 18 / 320
Chapter 1 Introduction
AMG1302/AMG1202-TSeries User’s Guide
18
1.6
Using the WPS Button
You can also use the
WPS
button to quickly set up a secure wireless connection between the
AMG1302/AMG1202-TSeries and a WPS-compatible client by adding one device at a time.
To activate WPS:
1
Make sure the
POWER
LED is on and not blinking.
2
Press the
WPS
button for 1-5 seconds and release it. See below for WPS button location.
3
Press the WPS button on another WPS-enabled device within range of the AMG1302/AMG1202-
TSeries. The
WPS
LED should flash while the AMG1302/AMG1202-TSeries sets up a WPS
connection with the other wireless device.
4
Once the connection is successfully made, the
WPS
LED shines green.
(WPS/WLAN)
Green
On
The wireless network is activated.
Blinking
The AMG1302/AMG1202-TSeries is communicating with other
wireless clients.
Green
Blinking
The AMG1302/AMG1202-TSeries is setting up a WPS connection.
Off
The wireless network is not activated.
(DSL)
Green
On
The DSL line is up.
Blinking
The AMG1302/AMG1202-TSeries is initializing the DSL line.
Off
The DSL line is down.
(INTERNET)
Green
On
The AMG1302/AMG1202-TSeries has an IP connection but no
traffic.
Your device has a WAN IP address (either static or assigned by a
DHCP server), PPP negotiation was successfully completed (if
used) and the DSL connection is up.
Blinking
The AMG1302/AMG1202-TSeries is sending or receiving IP traffic.
Red
On
The AMG1302/AMG1202-TSeries attempted to make an IP
connection but failed. Possible causes are no response from a
DHCP server, no PPPoE response, PPPoE authentication failed.
Off
The AMG1302/AMG1202-TSeries does not have an IP connection.
Table 1
LED Descriptions
LED
COLOR
STATUS
DESCRIPTION
WPS
Page 19 / 320
Chapter 1 Introduction
AMG1302/AMG1202-TSeries User’s Guide
19
1.7
The RESET Button
If you forget your password or cannot access the web configurator, you will need to use the
RESET
button at the back of the device to reload the factory-default configuration file. This means that you
will lose all configurations that you had previously and the user name and password will be reset to
the default.
1.7.1
Using the Reset Button
1
Make sure the
POWER
LED is on (not blinking).
2
To set the device back to the factory default settings, press the
RESET
button for ten seconds or
until the
POWER
LED begins to blink and then release it. When the
POWER
LED begins to blink,
the defaults have been restored and the device restarts.
1.8
Ways to Manage the AMG1302/AMG1202-TSeries
Use any of the following methods to manage the AMG1302/AMG1202-TSeries.
Web Configurator. This is recommended for everyday management of the AMG1302/AMG1202-
TSeries using a (supported) web browser.
FTP for firmware upgrades and configuration backup/restore.
Page 20 / 320
Chapter 1 Introduction
AMG1302/AMG1202-TSeries User’s Guide
20

Rate

3.7 / 5 based on 3 votes.

Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top