Chapter 3 Basic Setup

Parameter

Description

Encapsulation Mode

Encapsulation type of the IP packets:

°

VCMUX

°

LLC

802.1Q VLAN ID

VLAN ID

Priority

802.1P priority

Enable QinQ

Whether to enable QinQ

Firewall Enable

Whether to enable the firewall

Enable Proxy Arp

Whether to enable proxy ARP

5.

Click

Apply

.

6.

(Optional) To modify the network connection configurations, click

Edit

.

7.

(Optional) To delete the network connection configurations, click

Delete

.

– End of Steps –

3.3 Wireless Configuration

Wireless configuration includes the following:

l

Wireless basic configuration

l

Wireless security configuration

3.3.1 Configuring Basic Wireless Parameters

This procedure describes how to configure basic wireless parameters.

Steps

1.

Select

Setup > Wireless > Wireless Basic

.

The

WIRELESS BASIC

page is

displayed, see

Figure 3-19

.

3-17

SJ-20121120142951-001|2012-11-30 (R1.0)

ZTE Proprietary and Confidential

ZXHN H108N Maintenance Management Manual

Figure 3-19 WIRELESS BASIC Page

2.

Configure the wireless basic parameters. For a description of the parameters, refer to

Table 3-11

.

Table 3-11 Wireless Basic Parameter Descriptions

Parameter

Description

Enable Wireless

Whether to enable wireless

Enable MultiAP Isolation

Whether to enable isolation between multiple SSIDs

Wireless Network Name

(SSID)

SSID name

Visibility Status

l

Visible

l

Invisible

Country

Country or region

Control Sideband

l

Upper

l

Lower

Wireless Channel

Wireless channel, with the default of

Auto Scan

802.11 Mode

l

802.11b

l

802.11g

l

802.11n

l

802.11b/g

l

802.11n/g

l

802.11b/g/n

Band Width

l

20M

l

40M

l

20M/40M

3-18

SJ-20121120142951-001|2012-11-30 (R1.0)

ZTE Proprietary and Confidential

Chapter 3 Basic Setup

3.

Click

Apply

.

– End of Steps –

3.3.2 Configuring Wireless Security

The ZXHN H108N supports three wireless security modes, including Wired Equivalent

Privacy (

WEP

), Wi-Fi Protected Access (

WPA

), and WPA2.

WEP is the basic wireless

encryption standard. WPA and WPA2 provide higher levels of security.

None Security Mode

1.

Select

Setup > Wireless > Wireless Security

. The

WIRELESS SECURITY

page is

displayed, see

Figure 3-20

.

Figure 3-20 WIRELESS SECURITY Page

2.

From the

Security Mode

list, select

None

.

3.

Click

Apply

.

3-19

SJ-20121120142951-001|2012-11-30 (R1.0)

ZTE Proprietary and Confidential

ZXHN H108N Maintenance Management Manual

WEP Security Mode

1.

Select

Setup > Wireless > Wireless Security

. The

WIRELESS SECURITY

page is

displayed.

2.

From the

Security Mode

list, select

WEP

, see

Figure 3-21

.

Figure 3-21 WEP Parameter Configuration Area

3.

Configure the WEP parameters. For a description of the parameters, refer to

Table

3-12

.

Table 3-12 WEP Parameter Descriptions

Parameter

Description

WEP Key Length

l

64 bits (10 hex digits or 5 characters)

l

128 bits (26 hex digits or 13 characters)

Choose WEP Key

WEP provides four keys, which are from WEP Key1 to WEP Key4

WEP Key1/WEP Key2/WEP

Key3/WEP Key4

WEP provides four keys, which are from WEP Key1 to WEP Key4

3-20

SJ-20121120142951-001|2012-11-30 (R1.0)

ZTE Proprietary and Confidential

Chapter 3 Basic Setup

Parameter

Description

Authentication

l

Open

l

Share Key

4.

Click

Apply

.

Auto (WPA or WPA2) Security Mode

1.

Select

Setup > Wireless > Wireless Security

. The

WIRELESS SECURITY

page is

displayed.

2.

From the

Security Mode

list, select

Auto (WPA or WPA2)

.

3.

From the

WPA Encryption

list, select

AES

or

TKIP+AES

.

4.

Perform one of the following operations:

l

From the

WPA Mode

list, select

Auto (WPA or WPA2)-PSK

, see

Figure 3-22

.

Figure 3-22 WPA and Pre-Shared Key Parameter Configuration Area

Configure the WPA and Pre-Shared Key parameters.

For a description of the

parameters, refer to

Table 3-13

.

Table 3-13 WPA and Pre-Shared Key Parameter Descriptions

Parameter

Description

Group Key Update Interval

Interval of updating the group key

Pre-Shared Key

Password used to connect to the client

l

From the

WPA Mode

list, select

Auto(WPA or WPA2)-Enterprise

, see

Figure

3-23

.

3-21

SJ-20121120142951-001|2012-11-30 (R1.0)

ZTE Proprietary and Confidential