Page 46 / 127 Scroll up to view Page 41 - 45
ZXHN H108N Maintenance Management Manual
Parameter
Description
Secondary NTP time server
Secondary time server address
Current Local Time
Current local time
Time Zone
Time zone
Automatically adjust clock for daylight
saving changes
Whether to adjust time according to the daylight saving
time
3.
Click
Apply
.
– End of Steps –
3-32
SJ-20121120142951-001|2012-11-30 (R1.0)
ZTE Proprietary and Confidential
Page 47 / 127
Chapter 4
Advanced Configuration
Table of Contents
Advanced Wireless Configuration
...............................................................................
4-1
Configuring Port Forwarding
.....................................................................................
4-11
Configuring the DMZ
................................................................................................
4-13
Configuring the SAMBA Service
...............................................................................
4-14
Configuring the 3G WAN
..........................................................................................
4-15
Parental Control Configuration
.................................................................................
4-17
Filtering Options Configuration
.................................................................................
4-21
Qos Configuration
....................................................................................................
4-26
Configuring the Firewall
............................................................................................
4-30
Configuring a DNS
...................................................................................................
4-31
Configuring a Dynamic DNS
.....................................................................................
4-32
Network Tools Configuration
.....................................................................................
4-33
Routing Configuration
...............................................................................................
4-47
Configuring Schedules
.............................................................................................
4-53
Configuring NAT
.......................................................................................................
4-55
Enabling DLNA
.........................................................................................................
4-56
IP Tunnel Configuration
............................................................................................
4-57
4.1 Advanced Wireless Configuration
Advanced wireless configuration includes the configuration of the following:
l
Advanced settings
l
MAC filtering
l
Security settings
l
WPS settings
4.1.1 Configuring Advanced Parameters
This procedure describes how to configure the advanced parameters of the wireless LAN
interface.
Steps
1.
Select
Advanced > Advanced Wireless > Advanced Settings
. The
ADVANCED
SETTINGS
page is displayed, see
Figure 4-1
.
4-1
SJ-20121120142951-001|2012-11-30 (R1.0)
ZTE Proprietary and Confidential
Page 48 / 127
ZXHN H108N Maintenance Management Manual
Figure 4-1 ADVANCED SETTINGS Page
2.
Configure the advanced parameters.
For a description of the parameters, refer to
Table 4-1
.
4-2
SJ-20121120142951-001|2012-11-30 (R1.0)
ZTE Proprietary and Confidential
Page 49 / 127
Chapter 4 Advanced Configuration
Table 4-1 Advanced Settings Parameter Descriptions
Parameter
Description
Transmission Rate
Packet transmission rate on the wireless network
Multicast Rate
Multicast rate:
l
Lower
l
Higher
Transmit Power
Transmission power percentage of a wireless router, including
20%, 40%, 60%, 80%, and 100%
Beacon Period
Time period (sent with the beacon) before sending the beacon
again, which can be adjusted in milliseconds (ms)
RTS Threshold
Maximum number of packets that can be transmitted on the router
Fragmentation Threshold
Fragmentation threshold, which helps to improve the performance
of network transmission on the Radio Frequency (
RF
) interference
DTIM Interval
Wake-up interval of clients in power saving mode
Preamble Type
Length of the Cyclic Redundancy Check (
CRC
) block for
communication between the router and wireless clients
l
long
l
short
Enable Wireless/Enable
Wireless Guest Network
Whether to enable SSID or guest SSID
Wireless Network Name
(SSID)/Guest SSID
SSID name or guest SSID name
Visibility Status
l
Visible
l
Invisible
User Isolation
l
Off
l
On
WMM Advertise
Whether to enable WMM
Max Clients
Maximum number of clients that can be connected
3.
Click
Apply
.
– End of Steps –
4.1.2 Configuring MAC Filtering
This procedure describes how to configure MAC filtering, to permit or deny the device with
a specified MAC address to access the ZXHN H108N.
Context
MAC filtering is effective only for the user-side LAN, that is, upstream data flows.
4-3
SJ-20121120142951-001|2012-11-30 (R1.0)
ZTE Proprietary and Confidential
Page 50 / 127
ZXHN H108N Maintenance Management Manual
Steps
1.
Select
Advanced > Advanced Wireless > MAC Filtering
. The
MAC ADDRESS
page
is displayed, see
Figure 4-2
.
Figure 4-2 MAC ADDRESS Page
2.
Click
Add
.
Configure the MAC filtering parameters.
For a description of the MAC
filtering parameters, refer to
Table 4-2
.
Table 4-2 MAC Filtering Parameter Descriptions
Parameter
Description
Enable Access Control Mode
Whether to enable access control mode
MAC Address
MAC address that needs to be filtered
3.
Click
Apply
.
4.
(Optional) To delete a MAC filtering item, select it and click
Delete
.
– End of Steps –
4-4
SJ-20121120142951-001|2012-11-30 (R1.0)
ZTE Proprietary and Confidential

Rate

4.5 / 5 based on 2 votes.

Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top