1. Home
    2. /
  2. Manuals
    3. /
  3. ZTE
    4. /
  4. ZXHN H108N
    5. /
  5. 6
Page 26 / 127 Scroll up to view Page 21 - 25
ZXHN H108N Maintenance Management Manual
Parameter
Description
Dial-up mode
Dial-up mode, including the following:
°
AlwaysOn: When the configuration is complete, the sys-
tem gets online automatically and keeps online.
°
OnDemand: If there is no data flow in the connection
channel during the inactivity timeout period, the connec-
tion is interrupted automatically. If there are data flows
during the inactivity timeout period, the connection is re-
covered automatically.
°
Manual:
The subscriber gets online through manual
dial-up accordingly.
Inactivity Timeout
If there is no data flow in the connection channel during
the inactivity timeout period, the connection is interrupted
automatically. If there are data flows during the inactivity
timeout period, the connection is recovered automatically.
MRU Size
Maximum receive unit size.
MTU Size
Maximum transfer unit size.
Keep Alive
Sends Keep Alive packets to the NE periodically.
Lcp Echo Interval (sec)
Interval of sending the Echo Request packet.
Lcp Echo Failure
If a packet is not responded to during this time period, the
packet is considered failed.
Use Static IP Address
Uses the static IP address.
IP Address
Static IP address.
Enable NAT
When multiple computers in a Local Area Network (
LAN
)
share one IP address to access the Internet, Network
Address Translation (
NAT
) is used to translate each private
network address to the public network address of the Wide
Area Network (
WAN
) port.
NAT Type
°
Symmetric Nat
°
Full Cone Nat
Enable WAN Service
Whether to enable the WAN service.
If the WAN service is not enabled, the WAN link cannot
obtain an IP address.
Service Name
WAN link name.
iii.
Select
Backup 3G Enable
, see
Figure 3-13
.
3-12
SJ-20121120142951-001|2012-11-30 (R1.0)
ZTE Proprietary and Confidential
Page 27 / 127
Chapter 3 Basic Setup
Figure 3-13 3G CONNECTION BACKUP SETTINGS Area
l
PPP over Ethernet (PPPoE)
i.
From the
Protocol
list, select
PPP over Ethernet (PPPoE)
. Configure the
connection type parameters of the PPPoE protocol, see
Figure 3-14
.
Figure 3-14 CONNECTION TYPE Area–PPPoE
For a description of the PPPoE connection type parameters, refer to
Table
3-7
.
Table 3-7 Parameter Descriptions for the PPPoE Connection Type
Parameter
Description
Protocol
Connection protocol
Encapsulation Mode
Encapsulation type of the IP packets
°
VCMUX
°
LLC
802.1Q
VLAN
ID
VLAN ID
Priority
802.1P priority
Firewall Enable
Whether to enable the firewall
IPv4 Enable
Whether to enable Internet Protocol version 4 (
IPv4
)
IPv6 Enable
Whether to enable Internet Protocol version 6 (
IPv6
)
ii.
Configure the PPP parameters of the PPPoE protocol.
For a description of the PPP parameters, refer to
Table 3-6
.
iii.
Select
Backup 3G Enable
, see
Figure 3-13
.
l
MAC Encapsulation Routing (MER)
3-13
SJ-20121120142951-001|2012-11-30 (R1.0)
ZTE Proprietary and Confidential
Page 28 / 127
ZXHN H108N Maintenance Management Manual
i.
From
the
Protocol
list,
select
MAC
Encapsulation
Routing
(MER)
.
Configure the connection type parameters of the MER protocol, see
Figure
3-15
.
Figure 3-15 CONNECTION TYPE Area–MER
For a description of the MER connection type parameters, refer to
Table 3-8
.
Table 3-8 Parameter Descriptions for the MER Connection Type
Parameter
Description
Protocol
Connection protocol
Encapsulation
Mode
Encapsulation type of IP packets:
°
VCMUX
°
LLC
802.1Q VLAN ID
VLAN ID
Priority
802.1P priority
Firewall Enable
Whether to enable the firewall
IPv4 Enable
Whether to enable IPv4
IPv6 Enable
Whether to enable IPv6
Enable Proxy Arp
Whether to enable proxy Whether to enable ARP
ii.
In the
WAN IP SETTINGS
area, configure the WAN IP address parameters,
see
Figure 3-16
.
3-14
SJ-20121120142951-001|2012-11-30 (R1.0)
ZTE Proprietary and Confidential
Page 29 / 127
Chapter 3 Basic Setup
Figure 3-16 WAN IP SETTINGS Area
For a description of the parameters, refer to
Table 3-9
.
Table 3-9 Parameter Descriptions for the WAN IP Settings
Parameter
Description
Obtain address
automatically
Obtains the IP address automatically.
Use the following
address
Uses the static IP address.
WAN IP Address
WAN IP address.
WAN Subnet Mask
Subnet mask.
Default gateway
Default gateway.
Preferred DNS
server
Primary Domain Name Server (
DNS
) server address.
Alternate DNS
server
Secondary DNS server address.
Enable NAT
When multiple computers in a LAN share one IP address to
access the Internet, NAT is used to translate each private
network address to the public network address of the WAN port.
NAT Type
°
Symmetric Nat
°
Full Cone Nat
Enable WAN
Service
Whether to enable the WAN service.
If the WAN service is not enabled, the WAN link cannot obtain
an IP address.
Service Name
WAN link name.
iii.
Select
Backup 3G Enable
, see
Figure 3-13
.
3-15
SJ-20121120142951-001|2012-11-30 (R1.0)
ZTE Proprietary and Confidential
Page 30 / 127
ZXHN H108N Maintenance Management Manual
l
IP over ATM (IPoA)
i.
From the
Protocol
list, select
IP over ATM (IPoA)
. Configure the connection
type parameters of the IPoA protocol, see
Figure 3-17
.
Figure 3-17 CONNECTION TYPE Area–IPoA
For a description of the IPoA connection type parameters, refer to
Table 3-5
.
ii.
In the
WAN IP SETTINGS
area, configure the WAN IP address parameters,
see
Figure 3-16
.
For a description of the WAN IP address parameters, refer to
Table 3-9
.
iii.
Select
Backup 3G Enable
, see
Figure 3-13
.
l
Bridging
From
the
Protocol
list,
select
Bridging
.
Configure
the
connection
type
parameters of the Bridging protocol, see
Figure 3-18
.
Figure 3-18 CONNECTION TYPE Area–Bridging
For a description of the Bridging connection type parameters, refer to
Table 3-10
.
Table 3-10 Parameter Descriptions for the Bridging Connection Type
Parameter
Description
Protocol
Connection protocol
3-16
SJ-20121120142951-001|2012-11-30 (R1.0)
ZTE Proprietary and Confidential

Rate

4.5 / 5 based on 2 votes.

Popular ZTE Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top