ZTE ZXHN H108L Router Manual PDF (Setup & Configuration Guide)

Page 21 / 89 Scroll up to view Page 16 - 20

Confidential and Proprietary Information of ZTE CORPORATION

7

C h a p t e r

2

Product Installation

This chapter shows hardware connections for installing ZXHN H108L,

presents factory default settings, and describes how to configure a

computer for using ZXHN H108L.

Hardware Connections

1.

Place the ZXHN H108L router on the plane surface. Minimize

obstacles and the distance between the ZXHN H108L router and

the wireless terminal.

2.

ADSL/Ethernet uplink connection

A ZXHN H108L router can access the I

SP’s network

in ADSL

uplink mode.



ADSL uplink

The user is suggested to adopt the following connection method

for ADSL uplink mode, as shown in Figure 3.

F

IGU RE

3

ADSL

U

PLINK

C

ONNEC TIONS

Page 22 / 89

ZXHN H108L Wireless ADSL Router Maintenance Manual

8

Confidential and Proprietary Information of ZTE CORPORATION

If a telephone needs to be installed in front of the splitter, the

user must connect a voice filter in the Line port of the splitter;

then connect the phone to the splitter

’

s Phone port. The other

port connections can be referred to Figure 3.

A splitter consists of three ports:



Line: The port connected to the ADSL subscriber line.



Modem: The port connected to the ZXHN H108L

’

s LINE port.



Phone: The port connected to a phone.

Default Settings

The factory default settings for a ZXHN H108L router are listed as

follows:



IP address: 192.168.1.1; subnet mask: 255.255.255.0.



Use the DHCP server by default (i.e., the IP address can be

obtained from the ZXHN H108L automatically via DHCP).



Line coding: Auto negotiation (T1.413/G.DMT/G.LITE/ADSL2

/ADSL2+).

Page 23 / 89

Chapter 2 - Product Installation

Confidential and Proprietary Information of ZTE CORPORATION

9



Default network name (SSID) for WLAN, wireless encryption mode,

and encryption key are also marked on the label shown on the

cover of the ZXHN H108L router.

Note:

If the ZXHN H108L router fails to work due to error

configuration or if the user forgets the login password,

insert a needle into the device’

s

Reset

hole when the device

is running and hold

Reset

down for more than 10 seconds

to restore the settings to the default ones, then the system

restarts automatically.

Computer Configuration

This section shows how to check computer configuration and

configure TCP/IP for a ZXHN H108L.

Checking Computer Configuration

If the computer uses a proxy server to access the Internet, it is

suggested to disable this proxy service before performing the

configurations. It is recommended to close the VPN software and the

firewalls running on the computer. For example, in Microsoft Internet

Explorer, the user may check the proxy service configuration as

follows:

1.

In the browser, select

Tools > Internet Options

.

2.

Click the

Connections

tab and then click the

LAN Settings

button.

3.

Uncheck the

Use a proxy server for your LAN

box if it is

checked.

4.

Click the

OK

button.

Configuring TCP/IP

If the operating system of the computer is one of the following ones:

Windows95,

Windows98,

WindowsME,

Windows2000,

and

WindowsXP, there are two ways for configuring the computer (the

first one is recommended). The following instruction uses

Page 24 / 89

ZXHN H108L Wireless ADSL Router Maintenance Manual

10

Confidential and Proprietary Information of ZTE CORPORATION

WindowsXP as an example (the method under another operation

system is similar).



To obtain an address from the ZXHN H108L via DHCP, perform the

following procedure in the computer:

1.

In Windows taskbar, select

Start

>

Control Panel

.

2.

Double-click the

Network Connection

icon.

3.

Right click

Local Area Connection

,and select

Properties

.

4.

Select

Internet Protocol (TCP/IP)

, and then click the

Properties

button.

5.

In the

Internet Protocol (TCP/IP) Properties

dialog box,

check

Obtain an IP address automatically

and check

Obtain

DNS server address automatically

.

6.

Click

OK

to confirm and save the settings.



To configure a static address, perform the following procedure in

the computer:

1.

In Windows taskbar, select

Start

>

Control Panel

.

2.

Double-click the

Network Connection

icon.

3.

Right click

Local Area Connection

,and select

Properties

.

4.

Select

Internet Protocol (TCP/IP)

, and then click the

Properties

button.

5.

In

Internet Protocol (TCP/IP) Properties

dialog box, check

Use the following IP address

to specify this computer's IP

address. This IP address shall be in the same network segment

as the LAN port address of the ZXHN H108L and shall be in the

form 192.168.1.x (x is a decimal integer between

2~254, for

example

,

192.168.1.2). Subnet mask is

set to

255.255.255.0

.

D

efault

g

ateway is set to 192.168.1.1.

6.

Check

Use the following DNS server addresses

. To set the

IP address of the DNS server

, c

ontact local service provider or

set it to 192.168.1.1.

Click

OK

to confirm and save the settings.

Page 25 / 89

Confidential and Proprietary Information of ZTE CORPORATION

11

C h a p t e r

3

Configuration Page Login

This chapter introduces how to log into the configuration page and

presents the default main page after login.

Follow the precedures below to log into the web configuration page.



To log into configuration page:

1.

Open a brows

er

(e.g, IE)

and t

ype

http://192.168.1.1

(i.e.,

default IP address

of

the ZXHN H108L

’

s LAN port) in the address

bar.

2.

Press the

Enter

key of the keyboard to display the login dialog

box, as shown in Figure 4.

Rate

Popular ZTE Models

Famous Router IPs

Famous Router Companies

Bookmark Our Site

Share