1. Home
    2. /
  2. Manuals
    3. /
  3. Zonet
    4. /
  4. ZSR0104CP
    5. /
  5. 5
Page 21 / 63 Scroll up to view Page 16 - 20
Page
14
b.
Idle Time
field:
If the
Idle Time
was specified with non-zero number, ZSR0104C
SERIES router disconnects the PPPoE session after there was no data traffic on WAN
interface within the specified “I
dle Time
” minutes.
c.
Auto-reconnect
field: Once there is any outgoing data traffic, the router automatically
re-establishes the PPPoE session.
D. PPTP Connection
If Internet access is through the PPTP, please click the selection button of the “
PPTP
”. Then click
“Next” button.
PPTP is a common type of Internet access provided by many Internet Service Providers. It
requires you to enter the
User Name, Password, Server IP Address, My IP Address, My
Subnet Mask and Connection ID
to obtain authentication. Additional two optional fields
might be assigned value by user:
Downloaded from
www.Manualslib.com
manuals search engine
Page 22 / 63
Page
15
a.
Idle Time
field:
If the
Idle Time
was specified with non-zero number, ZSR0104C
SERIES router disconnects the PPTP session after there was no data traffic on WAN
interface within the specified “I
dle Time
” minutes.
b.
Auto-reconnect
field: Once there is any outgoing data traffic, the router automatically
re-establishes the PPTP session.
Click the button
Next
, the “LAN Setting” page, Figure 4 – 3, appears on the screen.
Figure 4 – 3
Step 4. The ” LAN Setting” page is used to configure ZSR0104C SERIES IP address of LAN
interface. You can assign the IP address from one of three private IP address groups
a.
10.x.x.x with subnet mask 255.0.0.0; x must be in range 0 to 255
b.
172.x.x.x with subnet mask 255.255.0.0; x must be in range 0 to 255
c.
192.168.x.x with subnet mask 255.255.255.0; x must be in range 0 to 255
Or a public IP address group with appropriated subnet mask.
Click the button
Next
, the “DHCP Setting” page, Figure 4 – 4, appears on the screen.
Figure 4 –4
Downloaded from
www.Manualslib.com
manuals search engine
Page 23 / 63
Page
16
Step 5. The ” DHCP Setting” page is used to configure DHCP Server and DHCP Client in LAN .If
DHCP Server enabled, the LAN PC Client can automatically obtain the IP settings,
including IP address, Domain Name, Subnet Mask, Primary DNS, and Secondary DNS from
ZSR0104C SERIES.
Step 6. Click the button “Finish “. ZSR0104C SERIES will save your settings and it will take
around 20 seconds to reboot. After finishing rebooting, the page will be redirected to the
Index Page,
Figure 4 - 2. Please verify if your current network status is correct.
4.3
WAN Setup Complete
Try to use your Web browser to access a website. If you can surf the website, congratulations!
ZSR0104C SERIES is now operating with the factory default settings. If you want to change the
default settings, please continue reading
Chapter 5 Configure Your ZSR0104C SERIES
.
If you could not access a website, please refer to
6.1 Troubleshooting
in
Chapter 6
Frequent Asked Questions
.
Chapter 5 Advanced Setup of ZSR0104C
SERIES
In addition to
“Wizard Setup
” in
Chapter 4 Use Your ZSR0104C SERIES
, you can setup
ZSR0104C SERIES router with more configuration options via the ”
advanced setting”
page. You
will enjoy ZSR0104C SERIES high performance after activating these advanced features.
5.1 Start from Advanced Setting
Step1. Launch a web browser on your client PC connected to ZSR0104C SERIES LAN interface
and point to
(192.168.1.1 is ZSR0104C SERIES default IP address.) If
the router was configured with a different IP address, use the configured address. Make sure
the computer IP address locates at the same subnet as router address. Press “Enter” key after
typing the router IP address. The status menu appears and shows the current system status
and all available settings.
If the main page does not pop up, please refer to
6.1 Troubleshooting
in
Chapter 6
Frequent Asked Questions
.
Downloaded from
www.Manualslib.com
manuals search engine
Page 24 / 63
Page
17
Step 2.
Click the “
Advanced Setup
“ (see Figure 4 – 2) and will be displayed, Figure 5 - 1.
Step 3.
The
Router Status
screen will show up and tell the current WAN and LAN IP settings of
your ZSR0104C SERIES, including IP address, Subnet Mask, Gateway, Primary DNS,
and Secondary DNS. On the left, you will see 5 main categories, including
System
,
Wan
,
Lan, Nat and Firewall
.
Figure 5 - 1
5.2 System
Click the “
System/System
” button, will see the Figure 5-2
Figure 5 - 2
The System page provides the NAT information.
Downloaded from
www.Manualslib.com
manuals search engine
Page 25 / 63
Page
18
5.3 Time
Click the “
System/Time
” button, will see the Figure 5-3
Figure 5 - 3
If you want to assign the timeserver, enter the IP address then click “Apply” button to save. If sntp
server gets time from network, the system time will display now time, else time is NULL. Local
time means the pc’s time, you can also set the pc’s time for system time. Click the “Set” button; the
system time will be equal to local time
The default
Time Server IP Address is 198.123.30.132, 210.59.157.10
And 192.5.5.250
5.4 Administration
Click the “
System/Admin
” button, will see the Figure 5-4
Figure 5 – 4
Downloaded from
www.Manualslib.com
manuals search engine

Rate

4 / 5 based on 1 vote.

Popular Zonet Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top