Page 16 / 63
Scroll up to view Page 11 - 15
Page
9
Step1. Launch a web browser on your client PC connected to ZSR0104C SERIES. Then point the
Web browser to
address.) If the router IP address was configured with different IP address, use the
configured IP address instead of
192.168.1.1. Please make sure your computer IP address is
located in the same subnet of the router IP address.
Step2. Press “Enter” key after typing the router IP address. The “user name and
Password” screen will appear (Figure 4.1). Enter the default ID “
admin”
and
the default password “
admin”
to obtain authentication. (Figure 4 –1) If the
User name and password were changed, type the latest user and password; then
Click the “
OK
” button. Then will see the Figure 4 – 2.
Figure 4 –1
You can also launch a Web browser in the Internet to access ZSR0104C SERIES
Web Configuration Tool by ZSR0104C SERIES “
Remote Management
.”
For more related information, refer to “
Manage from WAN side
” in
5.3
Administration
in
Chapter 5 Configure Your ZSR0104C SERIES
.
Step 3.
Select “
Setup Wizard
“ to quick setup ZSR0104C SERIES WAN access type and fill in
the necessary information provided by your Internet Service Provider.
Downloaded from
www.Manualslib.com
manuals search engine
Page 17 / 63
Page
10
Figure 4 –2
First please choose your local time zone to set time for your NAT. If have daylight saving click the
checkbox and input the start date and end date. Then click “
Next
” button.
Downloaded from
www.Manualslib.com
manuals search engine
Page 18 / 63
Page
11
You will see 4 options as followed. If Internet access is through the cable modem,
Please click the selection button of the “
Cable Modem
”. Then click “Next” button.
A. Cable Modem Connection
Two option fields might be required to enter by some Internet Service Providers.
a.
Host name
: a string of characters usually is the name of your PC, which is configured by
your ISP.
b. Clone MAC Address
:
It is your PC Ethernet Interface Card’s MAC address.
Downloaded from
www.Manualslib.com
manuals search engine
Page 19 / 63
Page
12
The default
WAN Settin
g of ZSR0104C SERIES is
Cable Modem Connection without
Host Name
and
MAC Clone
If you don’t know the MAC address of your Network Interface Card, follow the steps
to obtain the information. The MAC address information might be helpful when you
need to use MAC Clone.
1.
Go through the path “Start
->
Run” and enter “command” to enable the
Command
Prompt Window
.
2. Enter “
ipconfig/all
”. Find the item
Physical Address
and this is the MAC address
of your Network Interface Card.
B. Fixed-IP xDSL Connection
If Internet access is through the Fixed-IP, please click the selection button of
The” Fixed-IP xDSL”. Then click “Next” button.
Downloaded from
www.Manualslib.com
manuals search engine
Page 20 / 63
Page
13
Fixed - IP is a WAN access type provided by some Internet Service Providers. You need to
enter the information of IP address, Subnet Mask, Default Gateway, Primary DNS Server,
and Secondary DNS Server.
C. PPP over Ethernet (PPPoE) Connection
If Internet access is through the PPPoE, please click the selection button of
The” Dial-Up xDSL (PPPoE)”. Then click “Next” button.
PPPoE is a common type of Internet access provided by many xDSL Internet Service
Providers. It requires you to enter the
User Name
and the
Password
to obtain authentication
and ZSR0104C SERIES WAN IP address. Additional three optional fields might be assigned
value by user:
a.
MTU
field: As option, MTU field is used to specify the maximum transmit unit of a
packet over PPPoE link. Do not enter a number to this field only your Internet Service
Provider request a different MTU size from the default value, 1492 bytes. After
specifying these filed, remember to click the selection button
Downloaded from
www.Manualslib.com
manuals search engine
19216811.live