1. Home
    2. /
  2. Manuals
    3. /
  3. Zonet
    4. /
  4. ZSR0104CP
    5. /
  5. 3
Page 11 / 63 Scroll up to view Page 6 - 10
Page
4
concepts of ZSR0104C SERIES. Enjoy your use of ZSR0104C SERIES!
Organization of This User’s Manual
Chapter 1, Introduction
It briefly
describes the features of ZSR0104C SERIES.
Chapter 2, Get to Know the Hardware
It explains the LED and port functions on the front and back panels.
Chapter 3, Install Your ZSR0104C SERIES
It explains the hardware setup.
Chapter 4, Use Your ZSR0104C SERIES
It explains ZSR0104C SERIES
setup via “
Setup Wizard
” in the Web Configuration Tool.
Chapter 5, Configure Your ZSR0104C SERIES
It describes the default functions and advanced features via the Web Configuration Tool.
Chapter 6, Frequent Asked Questions
It provides solutions to common installation and configuration problems.
Appendix A,
It provides the procedure of
enabling DHCP client, disabling Web Proxy, and verifying the IP
settings in your client PC according to different Operating Systems.
Appendix B, Common Port Numbers
It offers a list of commonly used port numbers.
Appendix C, Terminology
It offers simple explanation of common networking terms in the User’s Manual.
Appendix D, Technical Support
It illustrates the methods to obtain technical support.
Downloaded from
www.Manualslib.com
manuals search engine
Page 12 / 63
Page
5
Chapter 2 Get to Know The Hardware
This Chapter explains ZSR0104C SERIES LED and Port functions.
2.1 LED Indicators
ZSR0104CP Front Panel
ZSR0104C Front Panel
Figure 2-1
Device Indicators
Power:
The Power LED illuminates whenever ZSR0104C SERIES is powered on.
Status:
The Status LED will be continuously on when the power is supplied. It
takes around 15 seconds to boot.
LAN and WAN Indicators
Link/Act Link :
ON means WAN (ADSL/Cable modem) is connected to
ZSR0104C SERIES.
Act (activity):
Blinking means data communication is happened.
If the LED is continuously illuminated, it means WAN device is
successfully connected or GSR0104A SERIES WAN port is working
now.
10/100
Indicates 10 or 100Mbps wire speed corresponding to WAN port. (On is
100Mps)
Downloaded from
www.Manualslib.com
manuals search engine
Page 13 / 63
Page
6
2.2
Back Panel
On the back panel, ZSR0104C SERIES has 4 RJ-45 10/100Mbps Ethernet LAN ports, and 1 RJ-45
10/100Mbps Ethernet WAN port. In addition, it has a Reload button and a Power Connector (7.5V
0.7A). (Figure 2-2)
ZSR0104CP Rear Panel
ZSR0104C Rear Panel
Figure 2-2
1. Local LAN Ports
ZSR0104C SERIES can function as a communication bridge between the LAN and the WAN. The
4 LAN ports can connect ZSR0104C SERIES to the client PCs in the LAN.
2. Internet WAN Port
The Internet WAN port provides connection between ZSR0104C SERIES and Cable Modem or
xDSL Box.
3. Reset Button
The reset Button can be used to restore the factory default parameters such as the password and
configuration settings.If you forget your password or want to restore the factory default settings into
your ZSR0104C SERIES, use the reset button to restore the factory default settings.
Step 1.
Disconnect ZSR0104C SERIES power adapter from the power outlet.
Step 2.
Press the
Reset
button on the back panel and keep holding it. Then plug ZSR0104C
Downloaded from
www.Manualslib.com
manuals search engine
Page 14 / 63
Page
7
SERIES power adapter into the power outlet.
Step 3.
It takes around 15 seconds to reset. The
Power LED
will turn on Green initially. Wait for
it becomes Red then release the
Reset
button.
Step 4.
Try to connect
via your Web browser. Use the user name “
admin
” and
the password “
admin
” to obtain authentication. If it is failed, please try the approach
again.
4. Power Connector
Power connector connects your ZSR0104C SERIES to the power adapter. When ZSR0104C
SERIES is connected to the correct power adapter and the power adapter is plugged into a power
outlet, the Power LED will be on and ZSR0104C SERIES will boot and start operating.
Chapter 3 Install Your ZSR0104C SERIES
3.1 Connect Client PC to ZSR0104C SERIES
Use an Ethernet cable to connect your client PC to ZSR0104C SERIES local LAN port.
ZSR0104C SERIES supports auto-crossover, so you can use either a Straight-
Through cable or a Crossover cable to connect the client PC to the LAN port.
3.2 Connect Ethernet Hub/Switch to ZSR0104C SERIES
If you have more than four clients, try to connect the hub or switch to ZSR0104C SERIES LAN
port with an Ethernet cable, then connect each client PC to a hub or switch with an Ethernet cable,
too.
3.3 Connect Wireless Access Point to ZSR0104C SERIES
You can extend the wired LAN by connecting Wireless Access Point to ZSR0104C SERIES LAN
port. Then a wireless network will be set up and it will turn into an infrastructure mode. The whole
network coverage will be expanded by Access Point wireless connection to the wireless clients.
3.4
Connect Cable/xDSL Modem to ZSR0104C SERIES
Use the Ethernet cable to connect a Cable Modem or xDSL Box to ZSR0104C SERIES Internet
Downloaded from
www.Manualslib.com
manuals search engine
Page 15 / 63
Page
8
WAN port.
3.5
Power up ZSR0104C SERIES
Connect the correct Power Adapter to ZSR0104C SERIES. Then plug the Power Adapter into an
AC power outlet. The LED status will be as followed.
1.
Power LED and the 4 LAN port’s LED will turn on for the first second.
2.
The Power LED will be continuously on when the power is supplied. It takes around 15
seconds to boot.
3.
The WAN and LAN link/act LED will be continuously on when ZSR0104C SERIES is
connected to the WAN and the LAN. The link/act LED will be flashing when the port is
transmitting data. The WAN and LAN 100 LED will be continuously on when the
transmission mode is 100Mbps. It will be off when the transmission mode is in 10Mbps.
Please use the correct AC adapter. It may cause damage to the router if
An improper AC adapter was used.
If the Power LED is not on, please refer to
6.1 Troubleshooting
in
Chapter 6 Frequent Asked Questions
.
Chapter 4 Use Your ZSR0104C SERIES
Follow the instructions in this chapter to perform the setup via “
Quick Setup
.” If you want to learn
more about the DHCP setup of your client PC, please refer to the section of
A.1
Enable DHCP in
Your PC
in
Appendix A: Configure TCP/IP in Your PC
.
4.1 Check the Web Proxy
Because the enabled-Web Proxy may cause your failure in accessing ZSR0104C SERIES Web
Configuration Tool, verify that you have disabled the Web Proxy before launching your Web
browser. If you do not know how to disable the Web Proxy, refer to the section of
Disable Web
Proxy
in
Appendix A: Configure TCP/IP in Your PC
.
4.2
Wizard Setup
Downloaded from
www.Manualslib.com
manuals search engine

Rate

4 / 5 based on 1 vote.

Popular Zonet Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top