Ubiquiti NanoStation-M5 Router Manual PDF (Setup & Configuration Guide)

Home

Manuals

Ubiquiti

NanoStation-M5

Page 11 / 20 Scroll up to view Page 6 - 10

Safety Notices

Read, follow, and keep these instructions.

Heed all warnings.

Only use attachments/accessories specified by the manufacturer.

WARNING:

Do not use this product in location that can be

submerged by water.

WARNING:

Avoid using this product during an electrical storm.

There may be a remote risk of electric shock from lightning.

Electrical Safety Information

Compliance is required with respect to voltage, frequency, and current

requirements indicated on the manufacturer’s label. Connection to a

different power source than those specified may result in improper

operation, damage to the equipment or pose a fire hazard if the limitations

are not followed.

There are no operator serviceable parts inside this equipment. Service

should be provided only by a qualified service technician.

This equipment is provided with a detachable power cord which has an

integral safety ground wire intended for connection to a grounded safety

outlet.

Do not substitute the power cord with one that is not the provided

approved type. Never use an adapter plug to connect to a 2-wire outlet

as this will defeat the continuity of the grounding wire.

The equipment requires the use of the ground wire as a part of the

safety certification, modification or misuse can provide a shock hazard

that can result in serious injury or death.

Contact a qualified electrician or the manufacturer if there are questions

about the installation prior to connecting the equipment.

Protective earthing is provided by Listed AC adapter. Building

installation shall provide appropriate short-circuit backup protection.

Protective bonding must be installed in accordance with local national

wiring rules and regulations.

Limited Warranty

UBIQUITI NETWORKS, Inc (“UBIQUITI NETWORKS”) warrants that the product(s)

furnished hereunder (the “Product(s)”) shall be free from defects in material

and workmanship for a period of one (1) year from the date of shipment by

UBIQUITI NETWORKS under normal use and operation. UBIQUITI NETWORKS’

sole and exclusive obligation and liability under the foregoing warranty shall

be for UBIQUITI NETWORKS, at its discretion, to repair or replace any Product

that fails to conform to the above warranty during the above warranty period.

The expense of removal and reinstallation of any Product is not included in this

warranty. The warranty period of any repaired or replaced Product shall not

extend beyond its original term.

Page 12 / 20

NanoStation

™

M/NanoStationloco

™

M Quick Start Guide

Warranty Conditions

The above warranty does not apply if the Product:

(I)

has been modified and/or altered, or an addition made thereto, except by

Ubiquiti Networks, or Ubiquiti Networks’ authorized representatives, or as

approved by Ubiquiti Networks in writing;

(II)

has been painted, rebranded or physically modified in any way;

(III)

has been damaged due to errors or defects in cabling;

(IV)

has been subjected to misuse, abuse, negligence, abnormal physical,

electromagnetic or electrical stress, including lightning strikes, or

accident;

(V)

has been damaged or impaired as a result of using third party firmware;

(VI)

has no original Ubiquiti MAC label, or is missing any other original Ubiquiti

label(s); or

(VII)

has not been received by Ubiquiti within 30 days of issuance of the RMA.

In addition, the above warranty shall apply only if: the product has been

properly installed and used at all times in accordance, and in all material

respects, with the applicable Product documentation; all Ethernet cabling runs

use CAT5 (or above), and for outdoor installations, shielded Ethernet cabling is

used, and for indoor installations, indoor cabling requirements are followed.

Returns

No Products will be accepted for replacement or repair without obtaining a

Return Materials Authorization (RMA) number from UBIQUITI NETWORKS during

the warranty period, and the Products being received at UBIQUITI NETWORKS’

facility freight prepaid in accordance with the RMA process of UBIQUITI

NETWORKS. Products returned without an RMA number will not be processed

and will be returned freight collect or subject to disposal. Information on the

RMA process and obtaining an RMA number can be found at:

www.ubnt.com/support/warranty

Disclaimer

EXCEPT FOR ANY EXPRESS WARRANTIES PROVIDED HEREIN, UBIQUITI

NETWORKS, ITS AFFILIATES, AND ITS AND THEIR THIRD PARTY DATA, SERVICE,

SOFTWARE AND HARDWARE PROVIDERS HEREBY DISCLAIM AND MAKE NO

OTHER REPRESENTATION OR WARRANTY OF ANY KIND, EXPRESS, IMPLIED

OR STATUTORY, INCLUDING, BUT NOT LIMITED TO, REPRESENTATIONS,

GUARANTEES, OR WARRANTIES OF MERCHANTABILITY, ACCURACY, QUALITY

OF SERVICE OR RESULTS, AVAILABILITY, SATISFACTORY QUALITY, LACK OF

VIRUSES, QUIET ENJOYMENT, FITNESS FOR A PARTICULAR PURPOSE AND

NON-INFRINGEMENT AND ANY WARRANTIES ARISING FROM ANY COURSE

OF DEALING, USAGE OR TRADE PRACTICE IN CONNECTION WITH SUCH

PRODUCTS AND SERVICES. BUYER ACKNOWLEDGES THAT NEITHER UBIQUITI

NETWORKS NOR ITS THIRD PARTY PROVIDERS CONTROL BUYER’S EQUIPMENT

OR THE TRANSFER OF DATA OVER COMMUNICATIONS FACILITIES, INCLUDING

THE INTERNET, AND THAT THE PRODUCTS AND SERVICES MAY BE SUBJECT

TO LIMITATIONS, INTERRUPTIONS, DELAYS, CANCELLATIONS AND OTHER

PROBLEMS INHERENT IN THE USE OF COMMUNICATIONS FACILITIES. UBIQUITI

Page 13 / 20

Compliance

NETWORKS, ITS AFFILIATES AND ITS AND THEIR THIRD PARTY PROVIDERS

ARE NOT RESPONSIBLE FOR ANY INTERRUPTIONS, DELAYS, CANCELLATIONS,

DELIVERY FAILURES, DATA LOSS, CONTENT CORRUPTION, PACKET LOSS, OR

OTHER DAMAGE RESULTING FROM ANY OF THE FOREGOING. In addition,

UBIQUITI NETWORKS does not warrant that the operation of the Products

will be error-free or that operation will be uninterrupted. In no event shall

UBIQUITI NETWORKS be responsible for damages or claims of any nature

or description relating to system performance, including coverage, buyer’s

selection of products (including the Products) for buyer’s application and/or

failure of products (including the Products) to meet government or regulatory

requirements.

Limitation of Liability

EXCEPT TO THE EXTENT PROHIBITED BY LOCAL LAW, IN NO EVENT WILL

UBIQUITI OR ITS SUBSIDIARIES, AFFILIATES OR SUPPLIERS BE LIABLE FOR DIRECT,

SPECIAL, INCIDENTAL, CONSEQUENTIAL OR OTHER DAMAGES (INCLUDING

LOST PROFIT, LOST DATA, OR DOWNTIME COSTS), ARISING OUT OF THE USE,

INABILITY TO USE, OR THE RESULTS OF USE OF THE PRODUCT, WHETHER BASED

IN WARRANTY, CONTRACT, TORT OR OTHER LEGAL THEORY, AND WHETHER OR

NOT ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.

Note

Some countries, states and provinces do not allow exclusions of implied

warranties or conditions, so the above exclusion may not apply to you. You may

have other rights that vary from country to country, state to state, or province

to province. Some countries, states and provinces do not allow the exclusion

or limitation of liability for incidental or consequential damages, so the above

limitation may not apply to you. EXCEPT TO THE EXTENT ALLOWED BY LOCAL

LAW, THESE WARRANTY TERMS DO NOT EXCLUDE, RESTRICT OR MODIFY, AND

ARE IN ADDITION TO, THE MANDATORY STATUTORY RIGHTS APPLICABLE TO

THE LICENSE OF ANY SOFTWARE (EMBEDDED IN THE PRODUCT) TO YOU. The

United Nations Convention on Contracts for the International Sale of Goods

shall not apply to any transactions regarding the sale of the Products.

Compliance

FCC

Changes or modifications not expressly approved by the party responsible for

compliance could void the user’s authority to operate the equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the

following two conditions:

This device may not cause harmful interference, and

This device must accept any interference received, including interference

that may cause undesired operation.

Page 14 / 20

NanoStation

™

M/NanoStationloco

™

M Quick Start Guide

NOTE: This equipment has been tested and found to comply with the limits

for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits

are designed to provide reasonable protection against harmful interference

when the equipment is operated in a commercial environment. This equipment

generates, uses, and can radiate radio frequency energy and, if not installed

and used in accordance with the instruction manual, may cause harmful

interference to radio communications. Operations of this equipment in a

residential area is likely to cause harmful interference in which case the user will

be required to correct the interference at his own expense.

For MPE and antenna usage details, please visit our website at

www.ubnt.com/products

Industry Canada

This Class A digital apparatus complies with Canadian ICES-003.

To reduce potential radio interference to other users, the antenna type and

its gain should be so chosen that the equivalent isotropically radiated power

(e.i.r.p.) is not more than that permitted for successful communication.

This device complies with Industry Canada licence-exempt RSS standard(s).

Operation is subject to the following two conditions:

This device may not cause interference, and

This device must accept any interference, including interference that may

cause undesired operation of the device.

This device has been designed to operate with the antennas listed below, and

having a maximum gain of 25 dBi*. Antennas not included in this list or having

a gain greater than 25 dBi are strictly prohibited for use with this device. The

required antenna impedance is 50 ohms.

* Model: NanoStation antenna gain is 25 dBi.

The maximum antenna gain permitted for devices in the bands

5250-5350 MHz and 5470-5725 MHz shall comply with the e.i.r.p. limit; and the

maximum antenna gain permitted for devices in the band 5725-5825 MHz shall

comply with the e.i.r.p. limits specified for point-to-point and non point-to-point

operation as appropriate.

Users should also be advised that high-power radars are allocated as primary

users (i.e. priority users) of the bands 5250-5350 MHz and

5650-5850 MHz and that these radars could cause interference and/or damage

to LE-LAN devices.

Cet appareil numérique de la classe A est conforme à la norme NMB-003

Canada.

Pour réduire le risque d’interférence aux autres utilisateurs, le type d’antenne

et son gain doivent être choisies de façon que la puissance isotrope

rayonnée équivalente (PIRE) ne dépasse pas ce qui est nécessaire pour une

communication réussie.

Cet appareil est conforme à la norme RSS Industrie Canada exempts de licence

norme(s). Son fonctionnement est soumis aux deux conditions suivantes:

Cet appareil ne peut pas provoquer d’interférences et

Cet appareil doit accepter toute interférence, y compris les interférences

qui peuvent causer un mauvais fonctionnement du dispositif.

Page 15 / 20

Compliance

Cet appareil a été conçu pour fonctionner avec les antennes énumérés ci-

dessous, et ayant un gain maximal de 25 dBi*. Antennes pas inclus dans cette

liste ou ayant un gain supérieur à 25 dBi sont strictement interdite pour une

utilisation avec cet appareil. L'impédance d'antenne requise est 50 ohms.

* Modèle: NanoStation gain d'antenne 25 dBi est.

Le gain maximal d'antenne permis pour les dispositifs utilisant les bandes 5 250-

5 350 MHz et 5 470-5 725 MHz doit se conformer à la limite de p.i.r.e.; le gain

maximal d'antenne permis (pour les dispositifs utilisant la bande 5 725-5 825

MHz) doit se conformer à la limite de p.i.r.e. spécifiée pour l'exploitation point à

point et non point à point, selon le cas.

Les utilisateurs devraient aussi être avisés que les utilisateurs de radars de

haute puissance sont désignés utilisateurs principaux (c.-à-d., qu'ils ont la

priorité) pour les bandes 5 250-5 350 MHz et 5 650-5 850 MHz et que ces radars

pourraient causer du brouillage et/ou des dommages aux dispositifs LAN-EL.

RF Exposure Warning

The antennas used for this transmitter must be installed to provide a separation

distance of at least 55.53 cm from all persons and must not be located or

operating in conjunction with any other antenna or transmitter.

Les antennes utilisées pour ce transmetteur doivent être installé en considérant

une distance de séparation de toute personnes d'au moins 55.53 cm et ne

doivent pas être localisé ou utilisé en conflit avec tout autre antenne ou

transmetteur.

CE Marking

CE marking on this product represents the product is in compliance with all

directives that are applicable to it.

Alert Sign (!) Follows CE Marking

Alert sign must be indicated if a restriction on use applied to the product and it

must follow the CE marking.

RoHS/WEEE Compliance Statement

English

European Directive 2002/96/EC requires that the equipment bearing this

symbol on the product and/or its packaging must not be disposed of with

unsorted municipal waste. The symbol indicates that this product should

be disposed of separately from regular household waste streams. It is your

responsibility to dispose of this and other electric and electronic equipment

via designated collection facilities appointed by the government or local

authorities. Correct disposal and recycling will help prevent potential negative

consequences to the environment and human health. For more detailed

information about the disposal of your old equipment, please contact your

local authorities, waste disposal service, or the shop where you purchased the

product.

Rate

Popular Ubiquiti Models

Famous Router IPs

Famous Router Companies

Bookmark Our Site

Share