Page 11 / 24
Scroll up to view Page 6 - 10
9
Note
: In the example below, the ADSL connection type is PPPoE.
Note
:
1. For Connection Trigger, select Continuous to keep the Internet connection always on.
2. Idle Disconnect allows you to configure an auto-disconnect time in seconds
(30-3600). The TEW-658BRM will automatically disconnect from the Internet if no
Internet activity has been detected within the period of Idle Disconnect entered.
6.
Select the desired ADSL connection type and
then click
Next
.
5.
Configure the settings based on information
provided by your ISP. Then Click
Next
.
7.
Configure the settings based on information
provided by your ISP. Then click Next. In most
cases for PPPoE connection method, you need
to configure the following and typically the
remaining default settings should be fine.
User Name
User Password
Mac Address (Clone Mac)
If Static is selected for IPMode of Connection
you would need to configure the following:
IP address
: The assigned IP address should
match your network.
This IP address should
not be used by any other network device on
your network.
Subnet Mask
: In most cases, the default
Subnet Mask (255.255.255.0) should be fine.
Page 12 / 24
10
8.
Configure the following for
Wireless Basic
Setting
and then click
Next
.
Device
: check Enable. Select Disable if you
do not want any wireless computers or device
to connect to this device.
SSID
: The SSID is the wireless network name
of your wireless network (e.g. wireless router or
access point). Enter a unique SSID (Network
Name). Do not use anything that would be
identifying like “Smith Family Network”.
Choose something that you would easily
identify when searching for available wireless
networks.
Wireless Channel
: In most cases, the default
channel
is fine.
Wireless Mode
: In most cases, the default
mode is fine.
Note
:
1. To protect your network from any unauthorized access it is recommended to enable
wireless encryption.
2. Once encryption is enabled on the router, each wireless computer and device must
be configured with the same encryption key.
3. The example below is for WPA2-PSK security. If you select WPA-PSK or
WPA2-PSK, make sure your wireless adapters support WPA or WPA2. If your
wireless adapters do not support WPA or WPA2, then select WEP.
Page 13 / 24
9.
Configure the following for security
configuration:
Security Mode
: WPA2
Authentication Type
: PSK
Encryption Type
: AES
Group Rekey Time
: In most cases, the default
time is fine.
Confirmed Passphrase
: Enter an encryption
key. For Example: trendnet
Then click
Next
.
For WPA-PSK or
WPA2-PSK, the Pre-Shared Key must be
between 8 and 63 ASCII or 64 HEX characters.
Make sure to copy down the encryption key.
10.
Click
OK
.
11.
Click
Reboot
.
12.
Click
OK
.
13.
Click
OK
.
11
Page 14 / 24
12
14.
Please wait while the TEW-658BRM reboots.
15.
Click
Finish
.
16.
Verify that the following panel lights are on:
DSL(Green) and Internet (Green).
17.
Open up your browser and enter in a URL
(e.g.
) to verify that you
have Internet connection.
www.trendnet.com
Your configuration is now complete
Register Your Product
To ensure the highest level of customer service and support, please take a moment to
register your product Online at:
www.trendnet.com/registe
r
Thank you for choosing TRENDnet
For detailed information regarding the
TEW-658BRM
’s
configuration and advanced settings,
please refer to the Troubleshooting section, User's Guide on the Utility CD-ROM, or
Page 15 / 24
says “The page cannot be displayed.” How can I get into the TEW-658BRM's web
configuration page?
1. Check your hardware settings again by following the instructions in section 2.
2. Make sure the
Power, LAN
and
Wireless
lights are lit.
3. Make sure your TCP/IP settings are set to Obtain an IP address automatically (see the
steps below).
4. If you are still having issues reset the TEW-658BRM.
To reset the TEW-658BRM, take a
pin or paperclip and press the reset button on the back of the Wireless Modem for 15
seconds. Then let go.
Troubleshooting
Windows 7
1.
Go into the
Control Panel
, click
Network and Internet
,
click
Network and Sharing Center
, click
Change
Adapter Settings
and then right-click the
Local Area
Connection
icon and then click
Properties
.
2.
Click
Internet Protocol Version 4(TCP/IPv4)
and then click
Properties.
Then
click on
Obtain an IP address automatically.
1.
Go into the
Control Panel
, click
Network and Internet
,
click
Network and Sharing Center
, click
Manage
Network Connections
and then right-click the
Local
Area Connection
icon and then click
Properties
.
Windows Vista
2.
Click
Internet Protocol Version 4(TCP/IPv4)
and then click
Properties.
Then click on
Obtain
an IP address automatically.
13
19216811.live