TRENDnet TEW-653AP Router Manual PDF (Setup & Configuration Guide)

Page 11 / 18 Scroll up to view Page 6 - 10

How do I configure TCP/IP settings on my computer?

I typed http://192.168.10.100 in my Internet Browser's Address Bar, but an error message

says “The page cannot be displayed.” How can I get into the TEW-653AP's web

configuration page?

1.

Check your hardware settings again by following the instructions in section 2

2. Make sure the wireless, LAN and power LEDs are lit.

3. Make sure the TCP/IP settings are configured properly (see first question).

4. Since the Access Point's default IP address is 192.168.10.100, make sure that no

other network devices are assigned an IP address of 192.168.10.100.

5. Reset the TEW-653AP.

Take a pin or paper clip and press the reset button for 15

seconds.

The reset button is located on top of the TEW-653AP.

Troubleshooting

Windows Vista

Windows XP/2000

1.

Go into the

Control Panel

, click

Network and

Internet

, click

Network and Sharing Center

,

click

Manage Network Connections

and then

right-click the

Local Area Connection

icon and

then click

Properties

.

2.

Click

Internet Protocol Version 4(TCP/IPv4)

and then click

Properties.

Then

click on

Use

the following IP address

, and make sure you

assign your network adapter an IP address in

the subnet of 192.168.10.x.

9

1.

Go into the

Control Panel

, double-click the

Network Connections

icon and then right-click

the

Local Area Connection

icon and then click

Properties

.

2.

Click

Internet Protocol (TCP/IP)

and then click

Properties.

Then

click on

Use the following

IP address

, and make sure you assign your

network adapter an IP address in the subnet of

192.168.10.x.

Page 12 / 18

If my network's IP is different than the Access Point's range, what should I do?

You should still configure the Access Point first. After all the settings are applied, go to the

Access Point's configuration page, click on

System,

click on

LAN

and change the IP address

of the Access Point to match your network's IP.

After I successfully configured the Access Point to match my network settings, I can not

connect to my network using wireless computers.

If you have a DHCP server in your network, you need to go into TCP/IP settings again and

re-select "Obtain an IP address automatically" to allow the PC to regain an IP address from

your DHCP server.

All the settings are correct, but I can not make a wireless connection to the Access Point.

1.

Double check that the wireless LED on the Access Point is lit.

2. Power cycle the Access Point.

Unplug the power to the Access Point.

Wait 15 seconds,

then plug the power back in.

3. Contact the manufacturer of your wireless network adapter.

Make sure the wireless

network adapter is configured with the proper SSID.

The default SSID of the Access Point

is

TRENDnet653.

The TEW-653AP does not power on when I plug the device into a Power-Over-Ethernet

switch or splitter.

What should I do?

1. Verify that the TEW-653AP powers up using the provided 12V, 1A power adapter.

2. Power cycle the PoE switch.

3. Unplug power to the switch, wait 15 seconds, then plug the power back in.

4.

Plug the device into a different port on the PoE switch.

5. Try using another Cat-5e cable.

If you still encounter problems or have any questions regarding the

TEW-653AP,

please contact

TRENDnet's Technical Support Department.

10

Page 13 / 18

11

The following are some general wireless tips to help minimize the impact of interference within an

environment.

Assign your network a unique SSID

Do not use anything that would be identifying like “Smith Family Network”. Choose

something that you would easily identify when searching for available wireless networks.

Do not turn off the SSID broadcast

The SSID broadcast is intended to be on and turning it off can cause connectivity issues.

The preferred method of securing a wireless network is to choose a strong form of encryption

with a strong and varied encryption key.

Change the channel

Most wireless access points and routers are defaulted to channel 6.

If you have a site survey

tool that will display the channels you can plan your channel selection around neighboring

access points to minimize interference from them.

If your site survey tool does not display

the channel try using channels 1 or 11.

Change the channel bandwidth

If you are using an 802.11n router or access point you can also make the following changes.

Change the channel bandwidth to 20/40MHz.

This will provide the highest possible

performance using an 802.11n device.

Also, if using 802.11n you should be securing the

network with WPA2 security.

Avoid stacking hardware on top of each other to prevent overheating issues

Maintain enough free space around the hardware for good ventilation and airflow.

There

should also be plenty of free space around the antennas to allow the wireless signal to

propagate.

Please also make sure that the wireless hardware is not placed in any type of

shelving or enclosures.

There are a number of other environmental factors that can impact the range of wireless

devices.

1. Adjust your wireless devices so that the signal is traveling in a straight path, rather than at

an angle.

The more material the signal has to pass through the more signal you will lose.

Note: after setting up the SSID, encryption type and encryption key/passphrase, please

make a note of them for future reference. You will need this information to connect your

wireless computers to the wireless router/access point.

Note:

Due to Wi-Fi certification considerations if you choose WEP, WPA or WPA2-TKIP

encryption this device may operate in legacy wireless mode (802.11b/g).

You may not get

802.11n performance as these forms of encryption are not supported by the 802.11n

specification.

Wireless Tips

Page 14 / 18

12

2.

Keep the number of obstructions to a minimum. Each obstruction can reduce the range of

a wireless device.

Position the wireless devices in a manner that will minimize the amount

of obstructions between them.

3.

Building materials can have a large impact on your wireless signal. In an indoor

environment, try to position the wireless devices so that the signal passes through less

dense material such as dry wall.

Dense materials like metal, solid wood, glass or even

furniture may block or degrade the signal.

4.

Antenna orientation can also have a large impact on your wireless signal. Use the wireless

adapter's site survey tool to determine the best antenna orientation for your wireless

devices.

5.

Interference from devices that produce RF (radio frequency) noise can also impact your

signal. Position your wireless devices away from anything that generates RF noise, such

as microwaves, HAM radios, Walkie-Talkies and baby monitors.

6.

Any device operating on the 2.4GHz frequency will cause interference. Devices such as

2.4GHz cordless phones or other wireless remotes operating on the 2.4GHz frequency

can potentially drop the wireless signal.

Although the phone may not be in use, the base

can still transmit wireless signals.

Move the phone's base station as far away as possible

from your wireless devices.

If you are still experiencing low or no signal consider repositioning the wireless devices or installing

additional access points.

The use of higher gain antennas may also provide the necessary

coverage depending on the environment.

Page 15 / 18

Rate

Popular TRENDnet Models

Famous Router IPs

Famous Router Companies

Bookmark Our Site

Share