Page 111 / 128
Scroll up to view Page 106 - 110
4.3.6.3. 802.1x PerPort Configuration
In this page, set the authorization status to activate 802.1x function by port
1. Select
<Edit>
.
2.
Status:
Press
<Space>
key to choose Fu / Fa / Au / No authorization status.
3. Press
Ctrl+A
go back action menu line.
4. Select
<Save>
to save all configure value.
Note:
Fu
Force the specific port to be unauthorized.
Fa
Force the specific port to be authorized.
Au
The state of the specific port was determined by the outcome of the authentication.
No
The specific port didn't support 802.1x function.
- 111 -
Page 112 / 128
4.3.6.4. 802.1x Misc Configuration
1. Press
<Edit>
.
2.
Quiet Period
Used to define periods of time during which it will not attempt to acquire a
supplicant (Default time is 60 seconds).
3.
Tx Period
Used to determine when an EAPOL PDU is to be transmitted (Default value is 30
seconds).
4.
Supplicant Timeout
Used to determine timeout conditions in the exchanges between the
supplicant and authentication server (Default value is 30 seconds).
5.
Server Timeout
Used to determine timeout conditions in the exchanges between the
authenticator and authentication server (Default value is 30 seconds).
6.
ReAuthMax
Used to determine the number of re-authentication attempts that are permitted
before the specific port becomes unauthorized (Default value is 2 times).
7.
Reauth Period
Used to determine a nonzero number of seconds between periodic
re-authentication of the supplications (Default value is 3600 seconds).
8. Press
Ctrl+A
go back action menu line.
9. Press
<Save>
to save configures value.
- 112 -
Page 113 / 128
4.4. Status and Counters
You can press the key of
Tab
or
Backspace
to choose item, and press
Enter
key to select item.
4.4.1. Port Status
This page display every port status
Link Status:
Display the port is link or no link.
- 113 -
Page 114 / 128
InRate:
Display the input rate control (100K/unit) setting value.
OutRate:
Display the output rate control (100K/unit) setting value.
Enabled:
Display the port is enabled or disable depended on user setting. Enable will be display
“Yes”, disable will be display “No”. If the port is unlink will be treated as “No”.
Auto:
Display the port is link on which Nway mode: Auto, Nway_Force, and Force.
Spd/Dpx:
Display the port speed and duplex.
FlowCtrl:
In auto / Nway force mode, display the flow control status is enable or not after
negotiation.
In force mode, display the flow control status is enabling or disable depending on user setting.
Actions->
<Quit>:
Exit the page of port status, and return to previous menu.
<Previous Page>:
Display previous page.
<Next page>:
Display next page.
4.4.2. Port Counters
The following information provides a view of the current status of the unit.
Actions->
<Quit>:
Exit the page of port status, and return to previous menu.
<Reset All>:
Set all count to 0.
<Previous Page>:
Display previous page.
<Next page>:
Display next page.
- 114 -
Page 115 / 128
4.4.3. System Information
MAC Address:
The unique hardware address assigned by manufacturer.
Firmware Version:
Display the switch’s firmware version.
ASIC Version:
Display the switch’s Hardware version.
Module 1 Type:
Display the module 1 Type: 1000Tx or 100Fx ext. Depend on module card mode.
Module 1 information:
Display the information saved in EEPROM of module1.
Module 2 Type:
Display the module 2 Type: 1000Tx or 100Fx ext. Depend on module card mode.
Module 2 information:
Display the information saved in EEPROM of module2.
- 115 -
19216811.live