TRENDnet TEG-2248WS Router Manual PDF (Setup & Configuration Guide)

Page 11 / 46 Scroll up to view Page 6 - 10

Leave at least 10cm of space at the front and rear of the hub for

ventilation.

Install the Switch on a sturdy, level surface that can support its weight,

or in an EIA standard-size equipment rack.

For information on rack

installation, see the next section, Rack Mounting

.

When installing the Switch on a level surface, attach the rubber feet to

the bottom of each device. The rubber feet cushion the hub and

protect the hub case from scratching.

Rack Mounting

The switch can be mounted in an EIA standard-size, 19-inch rack,

which can be placed in a wiring closet with other equipment.

Attach

the mounting brackets at the switch’s front panel (one on each side),

and secure them with the provided screws.

Figure 1. Combine the Switch with the provided screws

Then, use screws provided with the equipment rack to mount each

switch in the rack.

Figure 2. Mount the Switch in the rack

10

Downloaded from

www.Manualslib.com

manuals search engine

Page 12 / 46

Connecting Network Cable

The Switch supports 10Mbps Ethernet or 100Mbps Fast Ethernet and

it runs both in half and full duplex mode using two pair of Category 5

cable.

The Switch also supports 2-Ports 1000Mbps Gigabit Ethernet that

runs in Auto-negotiation mode and 10Mbps Ethernet or 100Mbps Fast

Ethernet that runs both in half and full duplex mode and 1000Mbps

Gigabit Ethernet runs in full duplex mode using four pair of Category

5 Cable.

These RJ45 ports are Auto-MDI type port. The Switch can auto

transform to MDI-II or MDI-X type, so you can just make an easy

connection that without worrying if you are using a standard or

crossover RJ45 cable.

There are additional two mini-GBIC ports for optional mini-GBIC

module.

AC Power

The Switch used the AC power supply 100-240V AC, 50-60 Hz. The

power switch is located at the rear of the unit adjacent to the AC

power connector and the system fan. The switch’s power supply will

adjust to the local power source automatically and may be turned on

without having any or all LAN segment cables connected.

11

Downloaded from

www.Manualslib.com

manuals search engine

Page 13 / 46

Downloaded from

www.Manualslib.com

manuals search engine

Page 14 / 46

IDENTIFYING EXTERNAL COMPONENTS

This chapter describes the front panel, rear panel, and LED indicators

of the Switch.

Front Panel

The figure below shows the front panels of the Switch.

Figure 3. Front panel of 48+4G-port Gigabit Ethernet Switch

LED Indicator:

Comprehensive LED indicators display the status of the switch and

the network (see the LED Indicators chapter below).

Fast Ethernet Ports (Port 1~48):

These ports support network speeds of either 10Mbps or 100Mbps,

and can operate in half- and full- duplex transfer modes. These ports

also supports automatic MDI/MDIX crossover detection function

gives true “plug and play” capability, just need to plug-in the network

cable to the hub directly and don’t care if the end node is NIC

(Network Interface Card) or switch and hub.

Gigabit Ethernet Ports (Port 49~50):

The Switch is equipped with two Gigabit twisted pair ports, supported

auto negotiable 10/100/1000Mbps and auto MDI/MDIX crossover

detection function. These two ports can operate in half-duplex mode

for 10/100Mbps and full- duplex mode for 10/100/1000Mbps.

13

Downloaded from

www.Manualslib.com

manuals search engine

Page 15 / 46

mini-GBIC Ports (Port 51~52):

The Switch is equipped with two mini-GBIC ports, supported optional

1000BASE-SX/LX mini-GBIC module.

Note: When the port was set to “Forced Mode”, the Auto MDI/MDIX will be disabled.

Reset:

The Reset button is to reset all the setting back to the factory

default.

Note: Be sure that you recorded the setting of your device, else all the setting will be

erased when pressing the “Reset” button.

Rear Panel

Figure 4. Rear panel of the Switch

AC Power Connector:

This is a three-pronged connector that supports the power cord. Plug

in the female connector of the provided power cord into this connector,

and the male into a power outlet. Supported input voltages range from

100-240V AC at 50-60Hz.

14

Downloaded from

www.Manualslib.com

manuals search engine

Rate

Popular TRENDnet Models

Famous Router IPs

Famous Router Companies

Bookmark Our Site

Share