Page 91 / 131
Scroll up to view Page 86 - 90
User Manual for T2-B-Gawv1.4U10Y.BI
Teracom Limited
88
An ISO Certificed Company
request of the terminal. After disposing, the information is transmitted to the
super-level router. The system acts as a proxy for its hosts after you enable IGMP
proxy.
3.6.2
IPv4 Routing
3.6.2.1
Static Routing
Choose
Services
>
IPv4 Routing
and the following page appears. In this page,
you can configure static route and dynamic routing. A default route is used to send
IP packages of unknown destination address to the default gateway. The default
route defines the IP address where all data is forwarded.
The following table describes the parameters of this page.
Field
Description
Destination
The IP address that packets are sent to.
Netmask
The subnet mask of the destination IP
address.
Gateway
The gateway that the packets pass by during
Page 92 / 131
User Manual for T2-B-Gawv1.4U10Y.BI
Teracom Limited
89
An ISO Certificed Company
Field
Description
transmission.
WAN Interface
The WAN interface that the packets pass
through on the modem.
Click
Add
in the
Static Routing
page. In this page, you can add static routing. You
need to provide the destination IP address and netmask. You also need to enter
the gateway IP address or the interface through which the packets are forwarded in
the corresponding fields. The interface can be iplan, ipwan or you can specify the
interface that the modem has.
3.6.2.2
Dynamic Routing
Click
Dynamic Routing
in the
IP Static Route Settings
page. In this page, you
can configure the dynamic routing for any existing interface. You can enable or
disable operation mode and RIP version for a particular interface.
Page 93 / 131
User Manual for T2-B-Gawv1.4U10Y.BI
Teracom Limited
90
An ISO Certificed Company
Click
and the following page appears.
The following table describes the parameters of this page.
Field
Description
RIP Version
There are 1, 2, and Both options in the
drop-down list.
Operation Mode
You can choose
Provide Active
,
Passive
,
and
Send only
.
°
Choose
Active
for transmitting and
receiving RIP interactive information.
°
Choose
Passive
for
only
receiving
information.
°
Choose
Send Only
for transmitting
information.
Check to enable related interfaces and then click
Apply
to take the settings effect
immediately.
3.6.3
IPv6 Routing
Choose
Services
>
IPv6 Routing
and the following page appears. In this page,
you can configure static route and dynamic routing.
Page 94 / 131
User Manual for T2-B-Gawv1.4U10Y.BI
Teracom Limited
91
An ISO Certificed Company
The following table describes the parameters of this page.
Field
Description
Prefix
Enter the IPV6 IP address.
PrefixLength
Enter the length of the prefix. The prefix length is
not larger than 128bit.
Forward packets to
Select the packet route. You can select the packets
are forwarded to the gateway or WAN interface.
°
If set to gateway, you need to enter the
gateway address.
°
If set to WAN interface, you need to
choose the WAN interface.
3.6.4
Quality of Service
Choose
Services
>
Quality of Service
and the following page appears. This page
shows a summary of the QoS and scheduler settings available on the system.
Page 95 / 131
User Manual for T2-B-Gawv1.4U10Y.BI
Teracom Limited
92
An ISO Certificed Company
Click
Add
and the following page appears. In this page, you can specify quality of
service (QoS) rules to upstream traffic. All of specified conditions in the traffic rule
must be satisfied for the rule to take effect.
19216811.live