Page 121 / 185 Scroll up to view Page 116 - 120
123
Administration
After installation, the Giga762SX WLAN dsl user interface is protected by the
System Password
admin
. To prevent unauthorised changes being made to the configu-
ration, you should set a new System Password from time to time. You may already have
set a System Password when you set up the
Security Setup Wizard
. If so, you can
change it here.
ì
Enter the old
System Password
in the
Current password
field.
ì
Enter a new
System Password
in the
New password
field and repeat it in the
Confirm new password
field.
The System Password may contain up to 20 characters. The System Password is case
sensitive. Avoid proper names and all too obvious words. Use a combination of letters,
digits and special characters.
Idle time before log off:
ì
Enter the number of minutes after which the configuration program is to be ended
if no further entry is made. The default is 10 minutes. If you enter 0, the program
will never be ended automatically.
ì
Click
OK
to apply the settings.
Note
If you forget your System Password, you have to reset the Giga762SX WLAN dsl . This
returns
all
your settings to the factory configuration. This means the system password
is changed back to
admin
.
Page 122 / 185
124
Administration
System management
Your Giga762SX WLAN dsl offers you the option of using remote management and
phone-based management in addition to the configuration program that you access via
a PC in your local network.
ì
In the
Advanced Settings
menu, select:
Administration
System Management
Remote Management enables a PC that is not in your local network to be used to con-
figure the Giga762SX WLAN dsl via a standard Web browser. You can activate Remote
Management for one particular or for any PC.
For security reasons, this function is only available if you have previously changed the
system password for your device (see page 122).
You can start remote management by entering the public IP address in your Internet
browser. As Internet providers often change this each time you dial in, it is also worth
using dynamic DNS (see page 79).
ì
Click the option
On
, to activate
Remote Management
.
The field
IP address
shows the public IP address. The field
Dynamic DNS
displays
the
Domain name
of the DNS service, if you have activated this function (see
page 79).
Page 123 / 185
125
Administration
ì
You can change the
Port
via which you can access the configuration program from
the Internet, for example in order to mask and protect the configuration program
against unauthorised access.
ì
Access
: You can select
Read only
if you only wish to activate remote management
for reading or you can select
Full control
if you wish to activate it for reading and
writing.
ì
Allowed connections:
You can specify one particular PC or specify a range of IP
addresses of clients for Remote Management or you can activate this function for
any PC.
Select the required option from the list.
For the option
Only specified client
, enter the IP address of the client, or the first
and last IP address in the range you want to permit.
ì
If you have defined more than one
Connection service
(see page 62), choose from
the list the
Connection service
, for which you want configure
Remote Manage-
ment
.
ì
Click
OK
to accept the settings.Registration button
If your device is equipped with a hardware registration button (Scan button) for WPS
registration (see page 25), you can deactivate this button for security reasons.
ì
Click
disabled
to deactivate the WPS hardware registration button.
ì
Click
OK
to accept the settings.
Please remember:
If you permit several PCs then anyone who finds out your password can access this
user interface and therefore also your network! If it is needed, then you should
only activate this option for a short time.
Please remember:
u
The Internet provider may assign the IP address to the PC dynamically. This may
change the IP address. Make sure that the PC that is to access the router from
the Internet always has the same IP address.
u
For access to the configuration environment via Remote Management, you
must enter the address of the Giga762SX WLAN dsl to be managed in the
browser using the following format:
(x.x.x.x represents the IP address of the Giga762SX WLAN dsl).
Page 124 / 185
126
Administration
Backing up and restoring a configuration
When the Giga762SX WLAN dsl has been configured, it is recommended that you back
up the settings. This means you can restore the settings at any time if they are acciden-
tally deleted or overwritten.
You can also reset the configuration to the factory settings. You should always do this
before handing the device to an external person.
ì
In the
Advanced Settings
menu, select:
Administration
Save & Restore
Backing up configuration data
ì
For
Task
, activate the
Save configuration
option.
ì
Click
OK
.
You can then set the location in which the backup file is to be saved in a file selection
window.
ì
Select a local directory on your PC where you want to save the configuration file and
enter a file name.
ì
Click
Save
.
The current configuration data is now saved in the specified file.
Restoring the saved data
ì
For
Task
, activate the
Restore configuration
option.
ì
Enter the path of the backup file that you want to use to restore the configuration
or choose the file in the file system via the
Browse
button.
A window will appear prompting you to confirm the procedure.
Page 125 / 185
127
Administration
ì
Click
OK
. The configuration will now be updated.
Restoring factory settings
You can reset the Giga762SX WLAN dsl to the factory settings. You should do this before
making the device available to others or exchanging it through the dealer. Otherwise
unauthorised persons may use the Internet access data at your expense.
ì
Select
Reset configuration to factory default settings
and click
OK
.
A window will appear prompting you to confirm the procedure.
Reboot
If the Giga762SX WLAN dsl is not operating properly, you can reboot it. It should then
be ready for use again.
ì
In the
Advanced Settings
menu, select:
Administration
Reboot
ì
Click
OK
to reboot the device.
A window will appear prompting you to confirm the procedure.
Updating firmware
Since your device is managed by central maintenance the local firmware update is not
supported.
Note:
If the Giga762SX WLAN dsl is not operating properly, you can reboot it. It should then
be ready for use again .
Please remember that when the device is fully reset,
all
the configuration settings are
returned to the factory settings. This means that you will have to completely reconfig-
ure the Giga762SX WLAN dsl.

Rate

4 / 5 based on 1 vote.

Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top