Motorola NVG589 Router Manual PDF (Setup & Configuration Guide)

Page 151 / 216 Scroll up to view Page 146 - 150

151

set physical dsl profile-8c [ on | off ]

Enables or disables VDSL2 profile 8c governing upstream and downstream bandwidth. Default is

on

.

set physical dsl profile-8d [ on | off ]

Enables or disables VDSL2 profile 8d governing upstream and downstream bandwidth. Default is

on

.

set physical dsl profile-12a [ on | off ]

Enables or disables VDSL2 profile 12a governing upstream and downstream bandwidth. Default is

on

.

set physical dsl profile-12b [ on | off ]

Enables or disables VDSL2 profile 12b governing upstream and downstream bandwidth. Default is

on

.

set physical dsl profile-17a [ on | off ]

Enables or disables VDSL2 profile 17a governing upstream and downstream bandwidth. Default is

on

.

set physical dsl profile-30a [ on | off ]

Enables or disables VDSL2 profile 30a governing upstream and downstream bandwidth. Default is

off

.

set physical dsl bit-swap [ on | off ]

Turns DSL bit-swapping on or off. Bit-swapping is resilient to loss of hand-shake commands. Default is

on

.

set physical dsl trellis [ on | off ]

Turns trellis error correction encoding on or off. Default is

on

.

set physical dsl vectoring-enable [ off | on ]

Enables or disables VDSL2 vectoring. Vectoring enables VDSL2 to achieve its highest potential data rates,

exceeding 100 Mbps. Default is

off

.

set physical dsl vectoring-timeout-ms

milliseconds

If

vectoring-enable

is set to

on

, specifies a timeout interval in milliseconds. Default is

5000

.

set physical dsl nlnm-threshold [ 0 - 480 ]

Specifies the New Low Noise Model (NLNM) value between 0 and 480. Default is

60

.

set physical dsl transport [ atm | ptm | auto | off ]

Sets the DSL transport mode: Asynchronous (

atm

), Packet (

ptm

), Automatic (

auto

), or none (

off

). Default is

ptm

.

set physical dsl atm vcc 1 enable [ off | on ]

Turns

atm

on or off on vcc 1. Default is

on

.

Page 152 / 216

Administrator’s Handbook

152

set physical dsl atm vcc 1 aal-type [ aal5 | aal0pkt | aal0cell ]

Sets the ATM Adaptation Layer type (

aal-type

): AAL5, AAL0-packet, or AAL0-cell. Default is

aal5

.

set physical dsl atm vcc 1 datapath [ phy0fast | phy0interleaved ]

Sets the ATM datapath, Fast Path or Interleaved. Default is

phy0fast

.

set physical dsl atm vcc 1 encap-type [ llcsnap-eth | llcsnap-rtip | llcencaps-ppp

| vcmux-eth | vcmux-ipoa | vcmux-pppoa ]

Specifies the data link encapsulation type. Default is

llcsnap-eth

.

set physical dsl atm vcc 1 vpi [ 0 - 255 ]

Sets the Virtual Path Identifier (

vpi

) for the circuit. Default is

0

.

set physical dsl atm vcc 1 vci [ 32 - 65535 ]

Sets the Virtual Channel Identifier (

vci

) for the circuit. Default is

35

.

set physical dsl atm vcc 2 enable [ off | on ]

Turns

atm

on or off on vcc 2. Default is

on

.

set physical dsl atm vcc 2 aal-type [ aal5 | aal0pkt | aal0cell ]

Sets the ATM Adaptation Layer type (

aal-type

): AAL5, AAL0-packet, or AAL0-cell. Default is

aal5

.

set physical dsl atm vcc 2 datapath [ phy0fast | phy0interleaved ]

Sets the ATM datapath, Fast Path or Interleaved. Default is

phy0fast

.

set physical dsl atm vcc 2 encap-type [ llcsnap-eth | llcsnap-rtip | llcencaps-ppp

| vcmux-eth | vcmux-ipoa | vcmux-pppoa ]

Specifies the data link encapsulation type. Default is

llcsnap-eth

.

set physical dsl atm vcc 2 vpi [ 0 - 255 ]

Sets the Virtual Path Identifier (

vpi

) for the circuit. Default is

8

.

set physical dsl atm vcc 2 vci [ 32 - 65535 ]

Sets the Virtual Channel Identifier (

vci

) for the circuit. Default is

35

.

set physical dsl atm vcc

vcc_num

tx-queue

queue_name

Attaches the egress queue template to the atm vc when the queue type is egress.

set physical dsl atm vcc

vcc_num

rx-queue

queue_name

Attaches the ingress queue to the atm vc when the queue type is ingress.

Page 153 / 216

153

set physical dsl ptm datapath [ phy0fast | phy0interleaved ]

Sets the ATM datapath, Fast Path or Interleaved. Default is

phy0fast

.

set physical dsl ptm priority [ low | high ]

Sets the Packet Transfer Mode (

ptm

) priority. Default is

low

.

set physical dsl ptm tx-queue

queue_name

Attaches the egress queue template to the ptm interface when the queue type is egress.

set physical dsl ptm rx-queue

queue_name

Attaches the ingress queue to the ptm interface when the queue type is ingress.

set physical dsl atm vcc 1 auto-vpi-vci [ on | off ]

Turns Automatic VPI/VCI Detection on or off. If you leave the default

on

, the device will try a series of VPI/VCI

pairs that are commonly used by service providers. When one pair succeeds, the device will use this one for

future connections.

set physical dsl atm vcc 1 vpi-vci-list

vpi_vci_pairs

Specifies the series of VPI/VCI pairs that the device will use to attempt a connection. The default set ("0/35 8/35 0/

43 0/51 0/59 8/43 8/51 8/59") may changed.

set physical dsl atm vcc 1 qos enable [ off | on ]

Turns QoS off or on on the virtual circuit. Default is

off

.

set physical dsl power-save enable [ off | on ]

Turns power saving mode off or on. Default is

off

.

Ethernet interfaces

set physical enet [ 1 - 4 ] mac-addr-override

mac_addr

You can override your Gateway’s Ethernet MAC address with any necessary setting. Some ISPs require your

account to be identified by the MAC address, among other things. Enter your 12-character Ethernet MAC override

address as instructed by your service provider, for example: 12 34 AB CD 19 64

set physical enet [ 1 - 4 ] port media [ auto | 100-fd | 100-hd | 10-fd | 10-hd ]

Sets the Ethernet port’s media flow control: Automatic, 100 Mbps Full-Duplex, 100 Mbps Half-Duplex, 10 Mbps

Full-Duplex, or 10 Mbps Half-Duplex. Default is

auto

.

set physical enet [ 1 - 4 ] port mdix [ auto | on | off ]

Sets the Ethernet port’s crossover detection. Default is

off

.

set physical enet

[ 1 - 4 ] tx-queue

queue_name

Attaches the egress queue template to the ethernet interface when the queue type is egress.

Page 154 / 216

Administrator’s Handbook

154

set physical enet

[ 1 - 4 ] rx-queue

queue_name

Attaches the ingress queue to the ethernet interface when the queue type is ingress.

set physical enet [ 1 - 4 ] port power-save enable ""

Turns power saving mode off or on.

set physical ensw max-age

seconds

Sets the maximum delay on the Ethernet switch in seconds. Default is 300 (5 minutes).

set physical ensw qos-mode [ off | p-bit ]

Sets QoS up on Ethernet switch, classified by priority-bit mapping. Default is

off

. When

p-bit

is selected, packets

will be mapped from their priority (even if untagged) to one of four queues per-port in the Ethernet switch.

See

“

Quality of Ser

vice (QoS) Examples

” on page

207

for more information.

☛

Note

This only applies to packets sent from the host CPU to a switch port; it does not apply to port-to-port

traffic.

set physical ensw p-bit-map

pbit-to-4queue-map

Sets the mapping from the 8 priority-bits to the four queues in the Ethernet switch. The lowest priority queue is “1”,

and the highest priority queue is “4”.

Example:

Mapping is “1 1 2 2 3 3 4 4", where priority bit values 0 and 1 would map to queue 1, and values 2 and

3 would map to queue 2, etc.

Wireless interfaces

set physical wireless enable [ on | off ]

Enables or disables the wireless capability for supported Wi-Fi Gateways. Default is

on

.

Sets and locks the Gateway into the wireless transmission mode you want:

bg

,

b-only

,

g-only

,

bgn

,

n-only

,

an

, or

a-only

. For compatibility with clients using 802.11b (up to 11 Mbps transmission), 802.11g (up to 20+ Mbps),

802.11a (up to 54 Mbit/s using the 5 GHz band), or 802.11n (from 54 Mbit/s to 600 Mbit/s with the use of four spa-

tial streams at a channel width of 40 MHz), select

B/G/N

. To limit your wireless LAN to one mode or the other,

select

G-only

,

N-only

,

A-only

, or

B-only

, or some combination that applies to your setup. Default is

bgn

.

set physical wireless auto-channel [ off | on ]

Turns auto-channel detection

on

or

off

.

set physical wireless bandwidth [ narrow | wide ]

Specifies whether the Wi-Fi channel is

narrow

or

wide

band. Default is

narrow

in compliance with FCC require-

ments.

Page 155 / 216

155

set physical wireless default-channel [ 1... 11 ]

(1 through 11, for North America) on which the network will broadcast. This is a frequency range within the 2.4Ghz

band. Channel selection depends on government regulated radio frequencies that vary from region to region. The

widest range available is from 1 to 14. Europe, France, Spain and Japan differ. Channel selection can have a sig-

nificant impact on performance, depending on other wireless activity close to this Router. Channel selection is not

necessary at the client computers; the clients will scan the available channels seeking access points using the

same SSID as the client. Defaults to

6

.

set physical wireless power [ 1 - 100 ]

Sets some value lower than 100 percent transmit power if your Gateway is located close to other Wi-Fi Gateways

and causes interference. Defaults to

100

(percent).

set physical wireless mul2uni [ off | on ]

Turns wireless “many-to-one” packet scheduling

off

or

on

. Default is

off

.

set physical wireless ssid 1 enable [ on | off ]

Enables or disables the first (default) Wi-Fi SSID.

set physical wireless ssid 1 name

name

Specifies a name for the first Wi-Fi SSID. Defaults to a unique value per router of the form “ATTxxx”.

set physical wireless ssid 1 access-type [ none | allow | deny ]

Specifies the type of address list for defining MAC address filtering. If set to

allow

, only hosts with the specified

addresses will be permitted to join the WLAN of the specified SSID. If set to

deny

, any hosts except those with the

specified addresses will be permitted to join the specified SSID. Default is

none

.

set physical wireless ssid 1 access-list

mac_address

Specifies the MAC address of devices controlled by MAC address filtering.

set physical wireless ssid 1 hidden [ off | on ]

Enables or disables “closed system mode” for the specified SSID. If set to

on

, the specified SSID will not appear

on client scans. Clients must log into the SSID with the exact SSID name and credentials specified for that SSID.

set physical wireless ssid 1 isolate [ off | on ]

If set to

on

, blocks wireless clients from communicating with other wireless clients on the LAN side of the Gate-

way. Defaults to

off

.

set physical wireless ssid 1 security [ none | wep | wpa ]

Sets the wireless privacy type:

none

,

wep

, or

wpa-psk

. Default is

none

.

set physical wireless ssid 2 enable [ off | on ]

Enables or disables the second available SSID.

Rate

Popular Motorola Models

Famous Router IPs

Famous Router Companies

Bookmark Our Site

Share