15

Chapter 3: Installing the PrintServer Using the Setup Wizard

Installation

Wireless-G PrintServer with Multifunction Printer Support

18. Reconnect the power adapter to the PrintServer and click

Next

.

Wait a few moments while the system checks for the network.

19. Wait a few minutes while the PrintServer connects to your wireless network.

The next screen will indicate that the PrintServer is now part of your wireless network. Click

Next

.

The order in which you connected the PrintServer, router, and printer is important. If the PrintServer did not

connect to your wireless network, then click

Back

and review the steps you took.

Figure 3-20: Reconnect the Power Adapter

Figure 3-22: PrintServer on Wireless Network

Figure 3-21: Checking

Network Connection

Downloaded from

www.Manualslib.com

manuals search engine

16

Chapter 3: Installing the PrintServer Using the Setup Wizard

About the New Program Icons

Wireless-G PrintServer with Multifunction Printer Support

20. The PrintServer is now connected to your wireless network.

Next you need to install the PrintServer driver on your computer. Click

Set up Computer

, and go to

“Chapter 4: Installing the PrintServer Driver”.

About the New Program Icons

After you have run the Set up PrintServer Setup Wizard, the PrintServer program icons will appear in the Start

menu. To access these icons, click

Start

. Select

Programs

. Then select

Linksys MFP Network Adapter

. You

will have four options available:

•

To uninstall the PrintServer from your computer, click

Uninstall

.

•

To run the wizard that sets up the PrintServer driver, click

Diagnostic

. Refer to “Chapter 4: Installing the

PrintServer Driver” for details.

•

To access the diagnostic utility, click

PrintServer Utility

. For more information, refer to “Chapter 5: Using the

Diagnostic Utility”.

•

To run the wizard that sets up the PrintServer, click

Setup Wizard

. Refer to the previous section in this

chapter, “Installation”.

Figure 3-23: Continue to Set up Computer

Figure 3-24: New Program Icons

Downloaded from

www.Manualslib.com

manuals search engine

17

Chapter 4: Installing the PrintServer Driver

Overview

Wireless-G PrintServer with Multifunction Printer Support

Chapter 4: Installing the PrintServer Driver

Overview

This section installs the PrintServer’s software on your Windows 2000 or XP computers so they can use the

PrintServer for print jobs. (The PrintServer is fully compatible with Windows 2000 and XP.)

At this point, you must have the following:

•

the PrintServer hardware installed on your network. If not, refer to “Chapter 3: Installing the PrintServer Using

the Setup Wizard”.

•

TCP/IP installed on each of your computers. (TCP/IP is installed by default.)

•

an IP address assigned to each of the computers on your network. (In most networks, the network router

assigns IP addresses to the computers on the network.)

•

an IP address assigned to the PrintServer by you or your network router. By default the PrintServer has DHCP

enabled so the network router will automatically assign an IP address. If you need to manually assign an IP

address, run the Setup Wizard on the Setup CD-ROM (refer to “Chapter 3: Installing the PrintServer Using the

Setup Wizard”).

It is assumed that your CD-ROM drive’s letter name is designated as “D”.

If your CD-ROM drive is named another

letter, replace all instances of “D” with the appropriate letter.

Installation

1.

Make sure you have no programs or applications running on your computer.

2.

If you haven’t already done so, insert the Setup CD-ROM into the computer’s CD-ROM drive. The Setup CD-

ROM should run automatically. If it does not, click the

Start

button and choose

Run

. In the field that appears,

enter

D:\SetupWizard.exe

(if “D” is the letter of your CD-ROM drive).

HAVE YOU:

already set up your printer? Linksys recommends that you set up your printer and

install your printer’s driver before you install the PrintServer’s driver.

Downloaded from

www.Manualslib.com

manuals search engine

18

Chapter 4: Installing the PrintServer Driver

Installation

Wireless-G PrintServer with Multifunction Printer Support

3.

When you see the

Welcome

screen, click

Click Here to Start

to continue. Click

Exit

to end the installation.

Click

User Guide

button to view the User Guide.

4.

Click

Set up Computer

.

Figure 4-2: Set up Computer

Figure 4-1: Welcome

Downloaded from

www.Manualslib.com

manuals search engine

19

Chapter 4: Installing the PrintServer Driver

Installation

Wireless-G PrintServer with Multifunction Printer Support

5.

Select the printer connected to the PrintServer. Click

Next

.

6.

The Setup Wizard will install the PrintServer’s driver and re-install the printer drivers.

Make sure the printer is connected to the PrintServer, and click

Next

.

Figure 4-4: Check Printer Driver

Figure 4-3: Select Printer

NOTE:

If the PrintServer is not listed, click

Refresh

. If the PrintServer is not found, then follow

these instructions:

1.

Disconnect the power adapter from the PrintServer.

2.

Wait two seconds, and reconnect the power adapter to the PrintServer.

3.

If the PrintServer is not found, then click the checkbox to disable the firewall.

4.

Click

Refresh

again.

Downloaded from

www.Manualslib.com

manuals search engine