1. Home
    2. /
  2. Manuals
    3. /
  3. Linksys
    4. /
  4. WPSM54Gv100F
    5. /
  5. 3
Page 11 / 63 Scroll up to view Page 6 - 10
5
Chapter 2: Getting to Know the PrintServer
The Front Panel
Wireless-G PrintServer with Multifunction Printer Support
The Front Panel
The PrintServer’s LEDs are located on the front panel.
USB
Green/Orange. The
USB
LED lights up green when there is a printer connected to the USB port.
The LED flashes green when the PrintServer is sending data through the USB port. It lights up
orange when there is a problem with the USB printer.
Wireless
Green. The
Wireless
LED serves two purposes. If the LED is continuously lit, the PrintServer is
connected to the wireless network. If the LED is flashing, the PrintServer is sending or
receiving data from the wireless network.
Ethernet
Green/Orange. If the
Ethernet
LED is continuously lit green, the PrintServer is connected to a
device through the Ethernet port. The LED flashes green when the PrintServer is sending or
receiving data from the wired network. It flashes orange when there are collisions detected on
the Ethernet port.
Power
Green/Orange. If the
Power
LED is continuously lit green, then the PrintServer is ready for use.
The LED flashes green when the PrintServer is booting up, a system self-test is running, or the
firmware is being upgraded. It lights up orange when there is an error.
Figure 2-2: PrintServer’s Front Panel
Downloaded from
www.Manualslib.com
manuals search engine
Page 12 / 63
6
Chapter 3: Installing the PrintServer Using the Setup Wizard
Before You Begin
Wireless-G PrintServer with Multifunction Printer Support
Chapter 3: Installing the PrintServer Using the
Setup Wizard
Before You Begin
Note the PrintServer’s default name, which starts with “LK” (for example, LK71107). It is shown in the
Server
field
on the sticker located on the PrintServer’s back panel. During the Setup Wizard, this name is used to identify the
PrintServer you are currently installing.
Installation
To install the PrintServer, you will use the Setup CD-ROM to run the Setup Wizard. It is highly recommended that
you use a computer on the wired network to set up the PrintServer. However, if you only have a wireless network,
then you can use a computer on the wireless network to set up the PrintServer.
1.
Insert the Setup CD-ROM into the computer’s CD-ROM drive. The Setup Wizard should run automatically. If it
does not, click the
Start
button and choose
Run
. In the box that appears, enter
D:\SetupWizard.exe
(if “D” is
the letter of your CD-ROM drive).
2.
When you see the
Welcome
screen, click
Click Here to Start
to begin the installation. Click
Exit
to end the
installation. Click
User Guide
button to view the User Guide.
3.
If this is the first time you have installed the PrintServer, click
Set up PrintServer
. If you have already
installed and configured the PrintServer, click
Set up Computer
and proceed to “Chapter 4: Installing the
PrintServer Driver.”
Figure 3-1: Welcome
Figure 3-2: Set up PrintServer
HAVE YOU:
already set up your printer? Linksys recommends that you set up your printer and
install your printer’s driver before you install the PrintServer’s driver.
Downloaded from
www.Manualslib.com
manuals search engine
Page 13 / 63
7
Chapter 3: Installing the PrintServer Using the Setup Wizard
Installation
Wireless-G PrintServer with Multifunction Printer Support
4.
Disconnect the USB printer cable from the computer, and disconnect the printer’s power adapter from the
electrical outlet. Click
Next
.
5.
Connect the USB printer cable to the USB port on the PrintServer. Click
Next
.
Figure 3-3: Disconnect the USB Printer Cable and Power
Figure 3-4: Connect the PrintServer to the Printer
Downloaded from
www.Manualslib.com
manuals search engine
Page 14 / 63
8
Chapter 3: Installing the PrintServer Using the Setup Wizard
Installation
Wireless-G PrintServer with Multifunction Printer Support
6.
Connect the Ethernet network cable to your router. Connect the other end of the cable to the Ethernet port of
the PrintServer.
(The Ethernet connection is for configuration purposes only. Later you can disconnect the Ethernet network
cable when the PrintServer has connected wirelessly.)
Click
Next.
7.
Connect the power adapter to the PrintServer and an electrical outlet. Click
Next
.
Figure 3-5: Connect the PrintServer to the Router
Figure 3-6: Connect the Power to the PrintServer
NOTE:
The PrintServer does not have an on/off power switch.
Whenever its power adapter is
plugged into a power supply, the PrintServer is powered on. The PrintServer can be powered
on before, during, or after your network is powered on.
IMPORTANT:
Make sure you use the power adapter supplied with the PrintServer. Use of a
different power adapter could damage the PrintServer.
Downloaded from
www.Manualslib.com
manuals search engine
Page 15 / 63
9
Chapter 3: Installing the PrintServer Using the Setup Wizard
Installation
Wireless-G PrintServer with Multifunction Printer Support
8.
Reconnect the printer’s power adapter to the electrical outlet.
Click
Next
.
9.
Wait a few moments while the system searches for the PrintServer.
Select the appropriate PrintServer. If you cannot find the PrintServer, click
Refresh
.
Click
Next
.
Figure 3-7: Reconnect the Power to the Printer
Figure 3-8: Select the PrintServer
Downloaded from
www.Manualslib.com
manuals search engine

Rate

3.5 / 5 based on 2 votes.

Popular Linksys Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top