Page 16 / 63
Scroll up to view Page 11 - 15
10
Chapter 3: Installing the PrintServer Using the Setup Wizard
Installation
Wireless-G PrintServer with Multifunction Printer Support
10. If your network uses a router that automatically assigns IP addresses, select
Automatically obtain an IP
address (DHCP)
. If your network uses a static IP address, select
Set IP configuration manually
, and enter
the IP Address, Subnet Mask, and Gateway in the fields provided.
Click
Next
.
Figure 3-10: Configure IP Settings (Static IP)
static ip address:
a fixed address assigned to
a computer or device connected to a network.
ip
(internet protocol): a protocol
used to send data over a network
ip address
: the address used to identify
a computer or device on a network
Figure 3-9: Configure IP Settings (Automatic)
Downloaded from
www.Manualslib.com
manuals search engine
Page 17 / 63
11
Chapter 3: Installing the PrintServer Using the Setup Wizard
Installation
Wireless-G PrintServer with Multifunction Printer Support
11. Create a password and enter it in the
Password
field. Enter the new password again in the
Confirm
field.
Click
Next
.
12. Select the wireless network that the PrintServer should join. If you do not see the wireless network you want
to use, click
Refresh
and locate the network. Click
Next
and go to step 14.
If you want to manually enter the settings for the wireless network, click
Manual Setup
. Click
Next
and go to
step 13.
Figure 3-11: Set the PrintServer’s Password
Figure 3-12: Select the Wireless Network
Downloaded from
www.Manualslib.com
manuals search engine
Page 18 / 63
12
Chapter 3: Installing the PrintServer Using the Setup Wizard
Installation
Wireless-G PrintServer with Multifunction Printer Support
13. If you clicked Manual Setup, the
Configure Wireless Settings
screen appears with the
SSID
field. Enter the
SSID or name of the wireless network. This is the unique name shared by all devices in a wireless network.
The SSID is case-sensitive and should have 32 or fewer characters.
Click
Next
.
14. The wireless security method of your network should be automatically selected. The available methods are
WEP (64-Bit), WEP (128-Bit), WPA Pre-Shared Key (TKIP), or WPA2 Pre-Shared Key (AES). Proceed to the
instructions for your wireless security method.
If wireless security is disabled, keep the default,
Disabled
, and click
Next
.
WPA Pre-Shared Key (TKIP) or WPA2 Pre-Shared Key (AES)
Enter a Passphrase (also known as a Pre-Shared or Shared Key) that is 8-63 characters in length. Click
Next
.
Figure 3-14: Wireless Security - WPA Pre-Shared Key
Figure 3-13: Configure Wireless Settings
Downloaded from
www.Manualslib.com
manuals search engine
Page 19 / 63
13
Chapter 3: Installing the PrintServer Using the Setup Wizard
Installation
Wireless-G PrintServer with Multifunction Printer Support
WEP (128-Bit) or WEP (64-Bit)
Enter a Passphrase that has 16 or fewer alphanumeric characters. Click
Next
. A WEP key will be
automatically generated. (The Passphrase is compatible with Linksys wireless products only. You will have to
manually enter the WEP key on any non-Linksys wireless products.)
If you want to manually enter the WEP key, leave the
Passphrase
field blank and click
Next
. A new screen will
appear. In the
Key 1
field, enter 26 hexadecimal characters if you are using 128-bit WEP encryption. Enter
10 hexadecimal characters if you are using 64-bit WEP encryption. Valid hexadecimal characters are “0”-“9”
and “A”-“F”. Click
Next
.
15. Your old and new settings will be displayed. If you want to save the new settings, click
Next
. If you want to
make changes, click
Back
.
Figure 3-15: Wireless Security -
WEP (128-Bit)
Figure 3-17: Confirm New Settings
Figure 3-16: WEP Key
Downloaded from
www.Manualslib.com
manuals search engine
Page 20 / 63
14
Chapter 3: Installing the PrintServer Using the Setup Wizard
Installation
Wireless-G PrintServer with Multifunction Printer Support
16. Wait a few moments while the PrintServer’s settings are updated.
In the next few screens, you will disconnect and reconnect the PrintServer. Proceed in the order specified to
avoid any networking conflicts.
Disconnect the power adapter from the PrintServer. Click
Next
.
17. Disconnect the Ethernet network cable from the PrintServer and router. Click
Next
.
Figure 3-18: Disconnect the Power Adapter
Figure 3-19: Disconnect the Network Cable
Downloaded from
www.Manualslib.com
manuals search engine
19216811.live