1. Home
    2. /
  2. Manuals
    3. /
  3. Linksys
    4. /
  4. WPSM54Gv100F
    5. /
  5. 8
Page 36 / 63 Scroll up to view Page 31 - 35
30
Chapter 5: Using the Web-based Utility
The Wireless Tab - Security
Wireless-G PrintServer with Multifunction Printer Support
WEP
Default Transmit Key
. Select the Default Transmit Key used by your wireless network. This indicates which WEP
key your network uses for WEP encryption.
Passphrase
. Enter a Passphrase and click the
Generate Keys
button to automatically generate WEP Keys 1-4.
The Passphrase is case-sensitive and should have no more than 16 alphanumeric characters. It must match your
wireless network’s passphrase and is compatible with Linksys wireless products only. (Enter the WEP key(s)
manually on any non-Linksys wireless products.)
Key 1 to Key 4
. To enter the WEP keys manually, leave the
Passphrase
field blank and enter your WEP key(s). For
64-bit WEP encryption, each key must have 10 hexadecimal characters, while for 128-bit WEP encryption, the
key must have 26 hexadecimal characters. Valid hexadecimal characters are “0”-“9” and “A”-“F”.
Authentication
. Select your wireless network’s authentication type. The default is
Open System
, for which the
sender and the recipient do NOT use a WEP key for authentication. You can also choose
Shared Key
, for which
the sender and recipient use a WEP key for authentication.
Click the
Save
button to apply your changes, or click
Cancel
to cancel your changes.
Figure 6-8: Wireless Tab - Security (WEP)
Downloaded from
www.Manualslib.com
manuals search engine
Page 37 / 63
31
Chapter 5: Using the Web-based Utility
The Printer Tab - Scan
Wireless-G PrintServer with Multifunction Printer Support
The Printer Tab - Scan
By default, the computer that sent the print job will be disconnected three minutes after the print job is
completed. Use this screen to change the length of time the computer is connected to the printer.
Auto Disconnect
3 min after job completed
. To change the number of minutes before the computer is disconnected from the
printer, enter the new number (1-60) in this field.
Always connect
. If you want the computer to always be connected to the printer, click
Always connect
.
Click the
Save
button to apply your change, or click
Cancel
to cancel your change.
Figure 6-9: Printer Tab - Scan
Downloaded from
www.Manualslib.com
manuals search engine
Page 38 / 63
32
Chapter 5: Using the Web-based Utility
The Printer Tab - Internet Printing
Wireless-G PrintServer with Multifunction Printer Support
The Printer Tab - Internet Printing
Internet Printing allows you to automatically print any e-mails that are sent to a specific e-mail account on your
network. This is especially useful for printing information when you are not connected to the network. You can
print from any location where you can access e-mail.
Mail Server
Mail Server IP Address
. Enter the address of your mail server. (This value must be a fixed IP address.)
Account Name and Password
. Enter the Account Name and Account Password.
Verify Password
. Enter the password again in the
Verify Password
field.
Check Mail every
. Specify how often you want the PrintServer to check for e-mail to be printed.
Redirect unprintable Mail to
. Specify an e-mail address to which e-mails that cannot be printed are routed; this
is useful for both graphic-intensive e-mails and for troubleshooting purposes.
Printer
Printer Model
. Enter the Printer Model in the field provided. You can find this in the Device Manager.
Printer Port
. Choose the appropriate Printer Port from the drop-down menu: USB, the PrintServer’s USB port, or
Logical Printer 1-3
. The PrintServer has three logical or virtual printer ports. For example, you can have three
different configurations for your USB printer: Logical Printer 1 for landscape orientation, Logical Printer 2 for
double-sided copies, and Logical Printer 3 for manual feed. Then configure the Logical Printers on the Logical
Port tab, so Logical Printers 1, 2, and 3 will be mapped to the physical printer on the PrintServer’s USB port.
Options
Print every E-Mail
. Click this checkbox if you want to print every e-mail message.
Print Banner Page
. Enabled by default, this feature tells the PrintServer to print a banner page for every print job
(the banner page describes the print job). Click the checkbox to remove the checkmark and disable this feature.
Mail response when printed
. Click this checkbox if you want an e-mail sent when a print job is complete.
Click the
Save
button to apply your changes, or click
Cancel
to cancel your changes.
Figure 6-10: Printer Tab - Internet Printing
Downloaded from
www.Manualslib.com
manuals search engine
Page 39 / 63
33
Chapter 5: Using the Web-based Utility
The Printer Tab - Logical Port
Wireless-G PrintServer with Multifunction Printer Support
The Printer Tab - Logical Port
The Logical Printers tab contains the logical printer settings of the PrintServer. Configure them for each Logical
Printer.
The PrintServer has three logical or virtual printer ports. For example, you can have three different configurations
for your USB printer: Logical Printer 1 for landscape orientation, Logical Printer 2 for double-sided copies, and
Logical Printer 3 for manual feed. Then you will map Logical Printers 1, 2, and 3 to the physical printer on the
PrintServer’s USB port.
Select Printer
Logical Printer No.
From the
Logical Printer Port No:
drop-down menu, select the number (1-3) of the printer you
wish to configure. Click the
Get Data
button to update the display with the current data for the selected logical
printer.
Details
Pre-string (Hex)
. Enter the printer control string (in hexadecimal characters) to be sent to the printer before each
print job. This string cannot exceed 30 characters.
Post String (Hex)
. Enter the printer control string (in hexadecimal characters) to be sent to the printer after each
print job. This string cannot exceed 30 characters.
Convert LF to CR+LF
. If checked, LF (line feed) characters are changed to CR+LF (carriage return + line feed).
Click the
Save
button to apply your changes, or click
Cancel
to cancel your changes.
Figure 6-11: Printer Tab - Logical Port
Downloaded from
www.Manualslib.com
manuals search engine
Page 40 / 63
34
Chapter 5: Using the Web-based Utility
The Status Tab - Device
Wireless-G PrintServer with Multifunction Printer Support
The Status Tab - Device
The Device tab displays information about the PrintServer.
Server Details
The PrintServer’s settings and status information are displayed here. No values can be changed on this screen.
This screen is for information only. Click the
Refresh
button to update this information.
Upgrade
. If you want to upgrade the PrintServer’s firmware, follow these instructions:
1.
Visit
www.linksys.com
and download the firmware upgrade file for the Wireless-G PrintServer with
Multifunction Printer Support.
2.
Extract the file on your computer.
3.
On the
Device
screen, click the
Upgrade
button.
4.
On the
Firmware Upgrade
screen, enter the location of the extracted firmware file, or click the
Browse
button
to find this file.
5.
Click the
Start Upgrade
button, and follow the on-screen instructions.
Figure 6-12: Status Tab - Device
download
: to receive a file transmitted over a network
firmware
: the programming code
that runs a networking device
upgrade
: to replace existing software or
firmware with a newer version
Figure 6-13: Firmware Upgrade
Downloaded from
www.Manualslib.com
manuals search engine

Rate

3.5 / 5 based on 2 votes.

Popular Linksys Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top