Page 56 / 63 Scroll up to view Page 51 - 55
50
Appendix H: Regulatory Information
Wireless-G PrintServer with Multifunction Printer Support
Appendix H: Regulatory Information
FCC Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device
may not cause harmful interference, and (2) this device must accept any interference received, including interference that
may cause undesired operation.
This product has been tested and complies with the specifications for a Class B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used
according to the instructions, may cause harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which is found by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
Reorient or relocate the receiving antenna
Increase the separation between the equipment or devices
Connect the equipment to an outlet other than the receiver's
Consult a dealer or an experienced radio/TV technician for assistance
FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the
user’s authority to operate this equipment.
FCC Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment
should be installed and operated with minimum distance 20cm between the radiator and your body.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. IEEE 802.11b or
802.11g operation of this product in the USA is firmware-limited to channels 1 through 11.
Safety Notices
Caution: To reduce the risk of fire, use only No.26 AWG or larger telecommunication line cord.
Do not use this product near water, for example, in a wet basement or near a swimming pool.
Avoid using this product during an electrical storm. There may be a remote risk of electric shock from lightning.
Downloaded from
www.Manualslib.com
manuals search engine
Page 57 / 63
51
Appendix H: Regulatory Information
Wireless-G PrintServer with Multifunction Printer Support
Industry Canada Statement
This device complies with Industry Canada ICES-003 and RSS210 rules.
Déclaration d’Industrie Canada
Cet appareil est conforme aux normes NMB003 et RSS210 d'Industrie Canada.
Industry Canada Statement
Operation is subject to the following two conditions:
1.
This device may not cause interference and
2.
This device must accept any interference, including interference that may cause undesired operation of the device.
This device has been designed to operate with an antenna having a maximum gain of 2dBi. Antenna having a higher
gain is strictly prohibited per regulations of Industry Canada. The required antenna impedance is 50 ohms.
To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the EIRP is
not more than required for successful communication.
3.
Industry Canada Radiation Exposure Statement:
This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment
should be installed and operated with minimum distance 20cm between the radiator & your body.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
Avis d'Industrie Canada
L'utilisation de ce dispositif est autorisée seulement aux conditions suivantes :
1.
il ne doit pas produire de brouillage et
2.
il doit accepter tout brouillage radioélectrique reçu, même si ce brouillage est susceptible de compromettre le
fonctionnement du dispositif. Le dispositif a été conçu pour fonctionner avec une antenne ayant un gain maximum de 2
dBi. Les règlements d'Industrie Canada interdisent strictement l'utilisation d'antennes dont le gain est supérieur à
cette limite. L'impédance requise de l'antenne est de 50 ohms.
Afin de réduire le risque d'interférence aux autres utilisateurs, le type d'antenne et son gain doivent être choisis de
façon à ce que la puissance isotrope rayonnée équivalente (p.i.r.e.) ne soit pas supérieure au niveau requis pour obtenir
une communication satisfaisante.
3.
Avis d'Industrie Canada concernant l'exposition aux radiofréquences :
Ce matériel est conforme aux limites établies par IC en matière d'exposition aux radiofréquences dans un
environnement non contrôlé. Ce matériel doit être installé et utilisé à une distance d'au moins 20 cm entre l'antenne et
le corps de l'utilisateur.
L'émetteur ne doit pas être placé près d'une autre antenne ou d'un autre émetteur, ou fonctionner avec une autre
antenne ou un autre émetteur.
Downloaded from
www.Manualslib.com
manuals search engine
Page 58 / 63
52
Appendix H: Regulatory Information
Wireless-G PrintServer with Multifunction Printer Support
User Information for Consumer Products Covered by EU Directive 2002/96/EC on Waste Electric and Electronic
Equipment (WEEE)
This document contains important information for users with regards to the proper disposal and recycling of Linksys
products. Consumers are required to comply with this notice for all electronic products bearing the following symbol:
Downloaded from
www.Manualslib.com
manuals search engine
Page 59 / 63
53
Appendix H: Regulatory Information
Wireless-G PrintServer with Multifunction Printer Support
Downloaded from
www.Manualslib.com
manuals search engine
Page 60 / 63
54
Appendix H: Regulatory Information
Wireless-G PrintServer with Multifunction Printer Support
Downloaded from
www.Manualslib.com
manuals search engine

Rate

3.5 / 5 based on 2 votes.

Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top