Page 6 / 127 Scroll up to view Page 1 - 5
IP Telephony System
Figure 6-17: Voice - SIP Screen - RTP Parameters
36
Figure 6-18: Voice - SIP Screen - SDP Payload Types
36
Figure 6-19: Voice - SIP Screen - NAT Support Parameters
37
Figure 6-20: Voice - SIP Screen - PBX Parameters
38
Figure 6-21: Voice - SIP Screen - Auto Attendant Parameters
41
Figure 6-22: Voice - SIP Screen - PBX Phone Parameters
43
Figure 6-23: Voice - Provisioning Screen - Configuration Profile
44
Figure 6-24: Voice - Provisioning Screen - Firmware Upgrade
45
Figure 6-25: Voice - Provisioning Screen - General Purpose Parameters
46
Figure 6-26: Voice - Regional Screen - Call Progress Tones
47
Figure 6-27: Voice - Regional Screen - Distinctive Ring Patterns
48
Figure 6-28: Voice - Regional Screen - Distinctive Call Waiting Tone Patterns
49
Figure 6-29: Voice - Regional Screen - Distinctive Ring/CWT Pattern Names
49
Figure 6-30: Voice - Regional Screen - Ring and Call Waiting Tone Spec
50
Figure 6-31: Voice - Regional Screen - Control Timer Values
50
Figure 6-32: Voice - Regional Screen - Vertical Service Activation Codes
51
Figure 6-33: Voice - Regional Screen - Vertical Service Announcement Codes
54
Figure 6-34: Voice - Regional Screen - Outbound Call Codec Selection Codes
54
Figure 6-35: Voice - Regional Screen - Miscellaneous
55
Figure 6-36: Voice - FXS 1 Screen - Network Settings
58
Figure 6-37: Voice - FXS 1 Screen - SIP Settings
58
Figure 6-38: Voice - FXS 1 Screen - Subscriber Information
59
Figure 6-39: Voice - FXS 1 Screen - Dial Plan
60
Figure 6-40: Voice - FXS 1 Screen - Streaming Audio Server
60
Figure 6-41: Voice - FXS 1 Screen - Call Feature Settings
60
Figure 6-42: Voice - FXS 1 Screen - Audio Configuration
61
Figure 6-43: Voice - FXS 1 Screen - FXS Port Polarity Configuration
63
Figure 6-44: Voice - Line 1 Screen - Network Settings
64
Figure 6-45: Voice - Line 1 Screen - SIP Settings
64
Figure 6-46: Voice - Line 1 Screen - Subscriber Information
65
Page 7 / 127
IP Telephony System
Figure 6-47: Voice - Line 1 Screen - Dial Plan
67
Figure 6-48: Voice - Line 1 Screen - NAT Settings
67
Figure 6-49: Voice - Line 1 Screen - Proxy and Registration
67
Figure B-1: Auto-Attendant Message Options
83
Figure B-2: Voice - SIP Screen - Auto Attendant Parameters
84
Figure E-1: IP Configuration Screen
101
Figure E-2: MAC Address/Adapter Address
101
Figure E-3: MAC Address/Physical Address
102
Figure E-4: MAC Address Clone
102
Page 8 / 127
1
Chapter 1: Introduction
Welcome
IP Telephony System
Chapter 1: Introduction
Welcome
Thank you for choosing the Linksys IP Telephony System. The System combines the rich feature set of legacy PBX
(Private Branch eXchange) telephone systems with the convenience and cost advantages of Internet telephony. It
supports common key system features such as an auto-attendant, music-on-hold, call forwarding, three-way call
conferencing, and more.
The System is so easy to configure that a fully working system can be set up in minutes. New Linksys SPA-family
Internet telephones are automatically detected and registered when they are connected to the System. While the
System will work with any SIP-compatible Internet telephone, it is the ideal host for Linksys business telephones,
including model number: SPA941. The System supports the advanced features of these phones, such as shared
line appearances, hunt groups, call transfer, call park, and group paging. Plus, with its two FXS ports, the System
can support traditional analog devices such as telephones, fax machines, answering machines, media adapters.
How does the System do all of this? By connecting your analog phones or fax machines to the System and
connecting the System and Internet phones to your router, then the System can direct voice communications for
your network.
But what does all of this mean?
Networks are useful tools for sharing Internet access and computer resources. Multiple computers can share
Internet access, so you don’t need more than one high-speed Internet connection. With Internet phone service,
your Internet access can now be shared by your Internet phones as well. You will be able to make phone calls
using your Internet phone service account, even while another colleague is web browsing. Plus, you can access
one printer from different computers and access data located on another computer’s hard drive (with the right
permissions).
PCs on a wired network create a LAN, or Local Area Network. They are connected with Ethernet cables, which is
why the network is called “wired”. The System takes your wired network and lets you integrate Internet phones
and Internet phone service.
When you first install the System, Linksys strongly recommends that you use the Setup CD-ROM. If you do not
wish to run the Setup Wizard on the Setup CD-ROM, then use the instructions in the Quick Installation or this User
Guide to help you. These instructions should be all you need to get the most out of the IP Telephony System.
ethernet:
an IEEE standard network protocol
that specifies how data is placed on and
retrieved from a common transmission
medium.
lan
(local area network): the computers and
networking products that make up the network
in your home or office.
network
: a series of computers or devices
connected for the purpose of data sharing,
storage, and/or transmission between users.
NOTE:
Some of these features are set up from the
Internet phones.
Page 9 / 127
2
Chapter 1: Introduction
What’s in this Guide?
IP Telephony System
What’s in this Guide?
This user guide covers the steps for setting up a network with the System. Most users will only need to use
“Chapter 4: Getting Started.” When you’re finished, then you are ready to make calls within your system as well
as calls to the outside world.
You also have other chapter available for reference:
Chapter 1: Introduction
This chapter describes the System and this User Guide.
Chapter 2: Applications
This chapter discusses the most common scenarios for the System.
Chapter 3: Getting to Know the IP Telephony System
This chapter describes the physical features of the System.
Chapter 5: Using the Interactive Voice Response Menu
This chapter explains how to configure the System’s network settings when you access its Interactive Voice
Response Menu.
Chapter 6: Using the Web-based Utility
This chapter explains how to configure the settings of the System through the Web-based Utility.
Appendix A: Troubleshooting
This appendix describes some possible problems and solutions, as well as frequently asked questions,
regarding installation and use of the System.
Appendix B: Configuring the Nighttime Auto-Attendant
This appendix explains how to set up the auto-attendant for nighttime (non-business) hours.
Appendix C: Dial Plan and Auto-Attendant Scripting for Advanced Users
This appendix explains how to define the dial plan and auto-attendant instructions. (These instructions are for
advanced users only.)
Appendix D: New Music for the Music-on-Hold Feature
This appendix explains how to replace the System’s default music file with your own music file.
Appendix E: Finding the MAC Address and IP Address for Your Ethernet Adapter
This appendix instructs you on how to find the MAC address or Ethernet address of your PC’s Ethernet
network adapter.
Page 10 / 127
3
Chapter 1: Introduction
What’s in this Guide?
IP Telephony System
Appendix F: Windows Help
This appendix describes how you can use Windows Help for instructions about networking, such as installing
the TCP/IP protocol.
Appendix G: Glossary
This appendix gives a brief glossary of terms frequently used in networking.
Appendix H: Specifications
This appendix provides the technical specifications for the System.
Appendix I: Warranty Information
This appendix supplies the warranty information for the System.
Appendix J: Regulatory Information
This appendix supplies the regulatory information regarding the System.
Appendix K: Contact Information
This appendix provides contact information for a variety of Linksys resources, including Technical Support.

Rate

4.5 / 5 based on 2 votes.

Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top