1. Home
    2. /
  2. Manuals
    3. /
  3. Inteno
    4. /
  4. X5668B
    5. /
  5. 3
Page 11 / 92 Scroll up to view Page 6 - 10
X5668 / X5668U
User’s Guide
6
X5668U Rear Panel
The rear panel of this device will be described here which cover all rear panel
definitions of other models.
Figure 3.2: Rear Panel Connections
Connector definition:
Label
Function
Antenna
Connects to the 802.11b/11g enabled wireless devices in LAN
Power Switch
ON/OFF switch
Power Jack
Connects to the supplied power adapter
USB
Connects to a printer with USB client port
LAN1 ~ LAN4
Connects the device via Ethernet to your devices in LAN
Reset
A reset button to reset the device or reset to default settings
There are two ways to reset to default settings:
1.
Press the reset button and turn on the power, then keep
pressing the reset button for 5 seconds.
2.
Press the reset button for 1 second while the router is
up and running.
Then you can reset the modem with the default setting.
DSL Jack
Connects to the ADSL network
Page 12 / 92
X5668 / X5668U
User’s Guide
7
3
Connecting your device
This chapter provides basic instructions for connecting the device to a computer or
LAN and to the Internet.
In addition to configuring the device, you need to configure the Internet properties of
your computer(s). For more details, see the following sections in Appendix A:
Configuring Ethernet PCs section
Configuring Wireless PCs section
This chapter assumes that you have already subscribed a broadband service with
your Internet service provider (ISP). These instructions provide a basic configuration
that should be compatible with your home or small office network setup. Refer to the
subsequent chapters for additional configuration instructions.
Connecting the Hardware
This section describes how to connect the device to the power outlet and your
computer(s) or network.
WARNING
Before you begin, turn the power off for all devices.
These include
your computer(s), your LAN hub/switch (if applicable), and the device.
The diagram below illustrates the hardware connections. The layout of the ports on
your device may vary from the layout shown. Refer to the steps that follow for specific
instructions.
Figure 4: Overview of X5668U Hardware Connections
Page 13 / 92
X5668 / X5668U
User’s Guide
8
Step 1. Connect the WAN port to ADSL network
Connect the WAN port to the ADSL network which has the high speed internet
connection.
Step 2. Connect the Ethernet cable
Connect up to four single Ethernet computers or to a HUB/Switch directly to the
device via Ethernet cable(s).
Note that the cables do not need to be crossover cables; the switch provides MDI and
MDIX auto-detection.
Step 3. Attach the power connector
Connect the AC power adapter to the Power connector on the back of the device and
plug the adapter into a wall outlet or power strip. Turn on and boot up your computer(s)
and any LAN devices such as hubs or switches.
Step 4. Configure your Ethernet PCs
You must also configure the Internet properties on your Ethernet PCs. See
Configuring Ethernet PCs section.
Or, step 5. Install a Wireless card and connect Wireless PCs if the device is with
wireless interface
You can attach a Wireless LAN that enables Wireless PCs to access the Internet via
the device.
You must configure your Wireless computer(s) in order to access your device. For
complete instructions, see Configuring Wireless PCs section.
Next step
After setting up and configuring the device and PCs, you can log on to the device by
following the instructions in “Getting Started with the Web pages” on chapter 4. The
chapter includes a section called Testing your Setup, which enables you to verify that
the device is working properly.
Page 14 / 92
X5668 / X5668U
User’s Guide
9
4
Getting Start with the Web pages
The device includes a series of Web pages that provide an interface to the software
installed on the device. It enables you to configure the device settings to meet the
needs of your network. You can access it through a web browser on a PC connected
to the device.
Accessing the Web pages
To access the web pages, you need the following:
A laptop or PC connected to the LAN or WLAN port on the device.
A web browser installed on the PC. The minimum browser version requirement is
Internet Explorer v4 or Netscape v4. For the best display quality, use latest version of
Internet Explorer, Netscape or Mozilla Firefox
.
from any of the LAN computers, launch
your web browser, type the URL,
in the web address (or location)
box, and press [Enter]. The default IP address of the device is 192.168.1.1. Then
enter the default username and password: admin/admin to access the configuration
web page, if you have not changed the username and password. Please be informed
that strings of username and password are case-sentitive.
Figure 5: Login Page
The Menu comprises:
Device Information
:
provides the basic information of the system. It includes sub
menus, Summary, WAN, Statistics Route and ARP.
Page 15 / 92
X5668 / X5668U
User’s Guide
10
Advanced Setup
: provides information about the current configuration of various
system features with options to change the configuration. It includes the sub menus
WAN, LAN, NAT (shown in router mode), Security, Routing, DNS (shown in router
mode), DSL, Print Server and Port Mapping.
Wireless Setup
: provides wireless SSID, security, key and various options to change
the configuration. It includes the sub menu, Basic, Security, MAC Filter, Wireless
Bridge, Advanced, Quality of Service and Station Info.
Diagnostic
: provides the diagnostic utility to check the LAN and Wireless physical
connection and ADSL connection as well.
Management
: provides the administration utilities. It includes the sub menus, Settings,
System Log, TR-069 Client, Access Control, Update Software, and Save/Reboot.

Rate

4.5 / 5 based on 2 votes.

Popular Inteno Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top