Page 51 / 95
Scroll up to view Page 46 - 50
EG101
User’s Guide
45
Set the
Maximum Associated Wireless Client
Set
XPress Technology
enabled or disabled.
Set
54g Mode
to 54g Auto, 54g Performance, 802.11b, 54g LRS (limited rate
support).
Set
54g Protection
to AUTO if there are 802.11g and 802.11b coexisting in the
wireless network.
Set
Afterburner Technology
Set
Preamble Type
. A preamble is a signal that sync up the timing between
devices.
Set
Transmission Power
. Larger value means more coverage.
Click
Save/Apply
to save the configuration
Quality of Service
The device provides wireless quality of service, Wi-Fi Multimedia.
Figure 52: Wireless Setting – Quality of Service
Global Setting
Select to enable or disable
WMM (Wi-Fi Multimedia)
Select
to
enable
or
disable
WMM
No
Acknowledgement
.
Enabling
no-acknowledge can result in more efficient throughput but high error rates
Click
Save/Apply
to save the configuration
Page 52 / 95
EG101
User’s Guide
46
Station Information
The table shows up whole associated wireless clients the device and their status.
Figure 53: Wireless Setting – Station Information
Global Setting
Click Refresh to get the latest updated information
Page 53 / 95
EG101
User’s Guide
47
8
VoIP Setup
The VoIP Setup web page menu comprises:
Interface Setup
Provisioning Setup
SIP Setup
Line 1 Setup
Line 2 Setup
RTP/Codec Setup
Operational Setup
Interface Setup
This page allows you to specify the voice packets to pass through the specific
interface and to choose different country code to set voice related parameters
including ringing type, ringing frequency, tone type, tone frequency, cadence, etc..
Figure 54: VoIP Configuration – Interface Setup
Global Setting:
Select
Interface Name
that voice packet go through
Select
Location
where you are located
Click button to
Start SIP client
or
Stop SIP client
Page 54 / 95
EG101
User’s Guide
48
Provisioning Setup
This page allows you to setup the provisioning server if ISP uses this method to
provide customer’s configuration profile. The device will use TFTP protocol to get the
configuration information from the server.
Figure 55: VoIP Configuration – Provisioning Setup
Global Setting:
Check to Enable Provisioning
Check to Use TFTP URL and also enter the TFTP URL with configuration file
name if applicable
Enter the 3DES Key if the configuration file is encrypted
Click
Save
to save the configuration.
SIP Setup
This page allows you to setup the parameters of SIP protocol.
Figure 56: VoIP Configuration – SIP Setup
Page 55 / 95
EG101
User’s Guide
49
Global Setting:
Select the
SIP Transport Protocol
: UDP or TCP.
Enter the
Listen Port
number which is a port number of UDP or TCP.
Enter the
Maximum Redirect
number which is the number that VoIP may allow to
redirect or forward to.
Enter the
Failover Retries
number of seconds which ISP requests to retransmit if
there is no response received.
Enter the
STUN Server
(IP address or host name) and
Port Number
. The STUN
server is used to pass through NAT firewall. The default port number for STUN
application is 3478. Please check with your ISP to get detailed information.
Enter the
External IP
. It is a WAN IP address on the router which the ATA is
connected for the NAT mapping.
Enter the
Keep-alive Interval
of seconds. The device sends packet to inform SIP
server periodically.
Enter the
Session Expired
of seconds. The device will close the session in
seconds after the call is disconnected.
Check to
Enable Session Timer Feature
.
Click
Save
to save the configuration
Line 1 Setting
This page allows you to setup the parameters of
Line 1
including username, password,
codec, and call features.
Figure 57: VoIP Configuration – Line 1 Setting
Global Setting:
Select to Enable this line or not
19216811.live