1. Home
    2. /
  2. Manuals
    3. /
  3. Huawei
    4. /
  4. SmartAX-MT880v3
    5. /
  5. 4
Page 16 / 109 Scroll up to view Page 11 - 15
6
z
User name, password
2.2
Connecting MT800
2.2.1
Connecting ADSL Line
Simply plug one end of the twisted-pair telephone cable into the
Modem port of the splitter and insert the other end into the ADSL port
on the rear panel of MT800.
Use another telephone cable to connect the splitter and the
Phone Jack in the wall.
2.2.2
Connecting the computer to MT800
Use a straight-through cable to connect your computer and
MT800. You can connect the MT800 directly to a 10/100Base-TX
Ethernet adapter card on your PC with the provided Ethernet cable
as shown in this diagram.
Page 17 / 109
7
(1) Computer
(2) RJ-11 Tel Cable
(3) Phone
(4) RJ-45 Ethernet Cable
(5) Splitter
(6) Phone Jack
(7) MT800
(8) RJ-11 Tel Cable
Figure 2-1
Computer to MT800 connection
2.2.3
Connecting Ethernet LAN to MT800
MT800 may be connected to any 10/100Base-TX Ethernet port.
When connecting MT800 to any Ethernet device that is capable of
operating at speeds higher than 10Mbps, be sure that the device has
auto-negotiation mode enabled for the connecting port.
Use cross-over cable to connect MT800 and the uplink port of a
switch or hub. Be sure that the cable connecting the LAN to MT800 is
not longer than 100 meters.
Page 18 / 109
8
2.3
Powering On MT800
1)
Use the provided power adapter and plug it into a suitable
power source nearby.
2)
You should see the Power LED indicator light up, which
indicates the device is powered on.
3)
After a few seconds, look at the LAN LINK indicator and
make sure it with steady light, which indicates a valid
connection between the router and your computer.
Page 19 / 109
9
Chapter 3
Before Configuring
MT800
To configure MT800, you have to connect MT800 to a computer
as shown below. Use the provided straight-through cable.
(1)Computer
(2)RJ-45 Ethernet Cable
(3)MT800
Figure 3-1
Computer to MT800 connection
3.2
When to Configure the MT800
The factory default settings of MT800 have optimized all
functions, which made it can operate in most conditions of network.
Usually, for the users with simple network topology, the default
setting values can meet their basic requirements and need no
change.
Page 20 / 109
10
If the conditions of network have been changed by the
modification of security, scale, line of communication, protocol and
topology, for example, a demand of particular VPI and VCI, you
should adjust accordingly the default settings to be able to adapt to
the changes.
3.3
Configuring IP Settings on Your Computer
The steps of configure the IP settings are as below.
1)
Understand the default IP settings for MT800: IP address
(192.168.1.1), Subnet mask (255.255.255.0).
2)
Make sure your computer has the TCP/IP protocol installed
and enabled.
z
If you have an Ethernet port on your computer, it probably
already has TCP/IP protocol installed.
z
If you are using Windows XP, the TCP/IP is enabled by
default for standard installations.
3)
Configure the IP address and Subnet mask of your
computer to make the computer set in the same subnet
with the MT800, for example, IP address:192.168.1.100,
Subnet mask: 255.255.255.0.
For computers running non-Windows operating systems,
follow the instructions for your OS to configure the IP setting to
occupy the same subnet as MT800.
3.4
Accessing the Web-based Configuration
Manager
Once the computer has IP settings that allow it to access the
Web-based configuration manager, you can change the factory
default settings to enable the MT800 to connect to the Internet.

Rate

3.5 / 5 based on 2 votes.

Popular Huawei Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top