Huawei SmartAX-MT800v2 Router Manual PDF (Setup & Configuration Guide)

Page 96 / 109 Scroll up to view Page 91 - 95

86

5.7

RFC 2684 Route (IPoA) Configuration

Configurations on MT800

Location

Parameters

Comments

PVC

Select any one from the eight PVCs.

VPI/VCI

The value shall be provided by your ISP.

Operation Mode

Select “Enable”.

Encapsulation

The value shall be provided by your ISP.

Usually you can keep the default value:

LLC.

Connection Type

Select “RFC2684 Routed (IPoA)”.

IP Address and

Subnet Mast

The values shall be provided by your ISP.

Default Route

Select “Enable”.

ATM Setting

Gateway IP

Address

The value shall be provided by your ISP.

NAT

It is recommended to enable the function of NAT.

DNS

It is recommended to have DNS Relay function enabled.

And set DNS IP address provided by your ISP.

DHCP Mode

It is recommended to have DHCP Server function enabled.

Traffic Index

It is recommended to set 0.

Configurations on the user’s PC

IP Address and

network mask

It is recommended to set the mode as obtaining an IP address

automatically.

DNS

It is recommended to set the mode as obtaining a DNS server’s

IP address automatically.

Page 97 / 109

87

±

Note:

For other advanced configurations, please refer to Chapter 4

Web-based

Management.

Page 98 / 109

88

Chapter 6

Troubleshooting

6.1

Quick Troubleshooting

Failures

Instructions

Power light is

out.

1.

Ensure power adapter is well connected;

2.

Ensure the right power adapter is used.

ADSL LINK

light is out.

1.

Ensure the ADSL line is well connected;

2.

Ensure the telephone line before entering the house is

valid, try to test with a telephone;

3.

Check that there is no junction box before connecting

MT800, which has such components like capacitors or

diodes that could hinder back high frequency signals;

4.

Ensure the MT800 and telephones are connected in the

right way.

LAN LINK

light is out.

1.

Ensure you use the right cables from the MT800 to your PC;

2.

Ensure the connection is secured;

3.

Check if the NIC LED lights up;

4.

Ensure your Network Adapter works normally by examining

whether the item of “Networking Adapters” is labeled with

“

?”

or “

!

”. If it is, you may delete it and then click “Refresh”

to reinstall. Otherwise, you may try the NIC in another slot.

As a last resort, you have to replace the NIC.

Page 99 / 109

89

Failures

Instructions

Can’t access

the Internet.

Take the most common access mode as an example, in which a

dial-up application is installed on the user’s computer:

1.

Ensure that any of the problems above is not the reason;

2.

Ensure that the dial-up application is correctly installed and

set on your PC;

3.

Ensure that you have entered the right user name and

password;

4.

Ensure “Use Proxy Server” is set properly for IE, if the

problem still remains even after you have log into

successfully;

5.

Try more than one Web sites, in case of some Web server’s

being in failure.

6.2

FAQs

Q: Why can’t my computer access the Internet, even when

the physical links are well connected?

Check first whether the LEDs are in normal status. If they do,

you have to find help to adjust the settings on the MT800.

Q: I forget the username and password when I am to log

into the Web-based Configuration Manager. Or I just can’t

access the Web-based Configuration Manager.

1)

Please press reset button at the rear panel for 3 seconds to

restore the factory default settings of MT800.

2)

Indicate your NIC IP address to 192.168.1.3

3)

Disable Proxy service.

4)

Launch your Web browser and type in http://192.168.1.1

Page 100 / 109

90

5)

Use the default user name: admin and password: admin

Q: My configuration is gone after rebooting MT800.

If you want to keep your settings after reboot MT800. Please go

to Web-based Configuration Manager

Æ

“Save & Reboot”

Æ

“Save”

to save your configurations.

Figure 6-1

Save the changed setting

Q: I can’t upgrade with the new firmware.

Please make sure the file that you have downloaded is valid.

Q: Why can’t I access the Internet by using virtual dialing

through Microsoft’s Internet Gateway?

Internet Gateway supports PPPoE itself. No other PPPoE

terminal software shall be installed again.

Q: Why does my PC fall off line sometimes even with all

LEDs are in normal status?

There are several scenarios might cause this problem.

6)

Be disconnected by the ISP.

7)

Some ISPs will have idle timeout setting to avoid wasting

IP. When the end user connects to the Internet too long

Rate

Popular Huawei Models

Famous Router IPs

Famous Router Companies

Bookmark Our Site

Share