Page 86 / 109
Scroll up to view Page 81 - 85
76
4.19
Save & Reboot
Click the
Save & Reboot
in Wizard column to specify the
method of restart.
I.
Configuration page
Figure 4-42
Save & Reboot
II.
Parameter explanation
z
Save:
Save the current setting into the permanent storage
z
Reboot:
A simple reboot: This will put into effect any
configuration changes that have been successfully saved
to flash memory.
z
Factory Setting Reboot:
This reboots the device to
default settings provided by your ISP or the manufacturer.
Choosing this option erases any custom settings.
You should select the proper method to restart the system.
Page 87 / 109
77
Caution:
Do not reboot the device using the Reset button on the back panel of the MT800 to
activate new changes. This button resets the device settings to the manufacturer’s
default values. Any custom settings will be lost.
4.20
Firmware Upgrade
Click the hyperlink
Firmware Upgrade
in the Wizard column to
open the
Firmware Upgrade
page and update the system software.
Figure 4-43
Firmware upgrade
Upgrade File:
Type in the full path and file name of the firmware
file to be uploaded. Alternatively you may click the Browse button to
search for the file on your system.
When the file names have been entered, click the
Upload
button to start loading the firmware file. If the upload is successful, a
message informs you that it was successfully loaded. If the firmware
does not load, an error message informs you to try the upload again.
Check the file names and attempt to upload again. If the file still is not
loaded, reboot the device and try again.
Page 88 / 109
78
Caution:
Do not power off the MT800 during the firmware upgrade process. Otherwise, the
configuration in the flash could be damaged.
4.21
Alarm
Figure 4-44
Alarm
You can view the logs of alarm in response to system events.
Select Refresh rate from the drop-down menu. Click the
Save Alarm
button to save the log file to local disk. Click the
Clear
button to clear
the logs and
Refresh
button to view the recent alarm events.
Page 89 / 109
79
Chapter 5
Service Configuration
This section describes the configuration for six modes of
SmartAX MT800 ADSL router device for ADSL online service. The
contents include:
z
Preparation for service configuration
z
PPPoE
z
PPPoA
z
RFC 2684 Bridged (Pure Bridge)
z
RFC 2684 Bridged (Static IP)
z
RFC 2684 Bridged (DHCP)
z
RFC 2684 Route (IPoA)
5.1
Preparation for Service Configuration
Collect the following data firstly to perform the configuration:
Page 90 / 109
80
Virtual dialup
mode
DSL mode
Protocol
types
PPPoE
PPPoA
RFC
2648
Bridged
(Pure
Bridge)
RFC
2684
Bridged
(Static
IP)
RFC
2684
Bridged
(DHCP)
RFC
2684
Route
(IPoA)
Connec
tion
Type
Connecti
on Type
Connecti
on Type
Connecti
on Type
Connec
tion
Type
Connec
tion
Type
PPPoE
user
name
PPPoA
user
name
VPI/VCI
VPI/VCI
VPI/VCI
VPI/VCI
PPPoE
passwo
rd
PPPoA
passwor
d
None
WAN IP
None
WAN IP
VPI/VCI
VPI/VCI
None
Subnet
mask
None
Subnet
mask
Securit
y
Protoco
l
Security
Protocol
None
Default
gateway
None
Default
gatewa
y
Preparing
informati
on
None
None
None
DNS
DNS
DNS
5.2
PPPoE Configuration
Configurations on MT800
Location
Parameters
Comments
PVC
Select any one from the eight PVCs.
ATM Setting
VPI/VCI
The value shall be provided by your ISP.
19216811.live