Huawei HG8247H Router Manual PDF (Setup & Configuration Guide)

Page 266 / 358 Scroll up to view Page 261 - 265

Step 4

Configure the parameters of the WAN interface.

l

Configure the parameters of the WAN interface – Route

1.

Choose

InternetGatewayDevice

>

WANDevice

>

1

>

WANConnectionDevice

from the navigation tree. Click

Add

in the lower left part to create an instance.

2.

Choose

2

>

WANPPPConnection

from the navigation tree. Click

Add

in the lower

left part. Choose the new

1

branch from the navigation tree. In the right pane, set the

parameters as follows:

–

Set

Enable

to

1

, indicating that the WAN connection is enabled.

–

Set

Connection Type

to

IP_Routed

, indicating that the connection type of the

WAN interface is in routing mode.

–

Set

NATEnable

to

1

, indicating that the NAT function is enabled.

–

Set

Username

to

iadtest@pppoe

and

Password

to

iadtest

, indicating that the

PPPoE user name is

iadtest@pppoe

and the password is

iadtest

.

–

Set

X_HW_SERVICELIST

to

INTERNET

, indicating that the service type of

the WAN interface is Internet.

–

Set

X_HW_VLAN

to

40

, indicating that the VLAN ID of the WAN interface is

40.

–

Set

X_HW_PRI

to

1

, indicating that the priority level of the WAN interface is 1.

3 Configuration

EchoLife HG8240/HG8245/HG8247 GPON Terminal

Service Manual

3-228

Huawei Proprietary and Confidential

Issue 04 (2011-01-12)

Page 267 / 358

NOTE

l

If the WAN interface obtains IP addresses in static or DHCP mode, choose

WANIPConnection

to set the parameters of the WAN interface.

l

If the WAN interface obtains IP addresses in PPPoE mode, choose

WANPPPConnection

to

set the parameters of the WAN interface.

l

Configure the parameters of the WAN interface – Bridge

1.

Choose

InternetGatewayDevice

>

WANDevice

>

1

>

WANConnectionDevice

from the navigation tree. Click

Add

in the lower left part to create an instance.

2.

Choose

2

>

WANPPPConnection

from the navigation tree. Click

Add

in the lower

left part. Choose the new

1

branch from the navigation tree. In the right pane, set the

parameters as follows:

–

Set

Enable

to

1

, indicating that the WAN connection is enabled.

–

Set

Connection Type

to

IP_Bridged

, indicating that the connection type of the

WAN interface is in bridge mode.

–

Set

X_HW_SERVICELIST

to

INTERNET

, indicating that the service type of

the WAN interface is Internet.

–

Set

X_HW_VLAN

to

40

, indicating that the VLAN ID of the WAN interface is

40.

–

Set

X_HW_PRI

to

1

, indicating that the priority level of the WAN interface is 1.

EchoLife HG8240/HG8245/HG8247 GPON Terminal

Service Manual

3 Configuration

Issue 04 (2011-01-12)

Huawei Proprietary and Confidential

3-229

Page 268 / 358

Step 5

Bind the SSID.

Choose

InternetGatewayDevice

>

WANDevice

>

1

>

WANConnectionDevice

>

1

>

WANIPConnection

>

1

>

X_HW_LANBIND

from the navigation tree. In the right pane, set

SSID1Enable

to

1

, indicating that the WAN interface is bound to SSID 1.

3 Configuration

EchoLife HG8240/HG8245/HG8247 GPON Terminal

Service Manual

3-230

Huawei Proprietary and Confidential

Issue 04 (2011-01-12)

Page 269 / 358

----End

Result

l

Layer 3 bridge Wi-Fi service: SSID radio signals can be searched on the PC. After the user

enter the authentication key and pass the authentication, the user can access the Internet.

l

Layer 3 route Wi-Fi service: SSID radio signals can be searched on the PC. After the user

enter the authentication key and pass the authentication, the PC can obtain the IP address

allocated by the DHCP IP address pool on the ONT. After the PPPoE dialup is successfully

performed on the ONT, the user can access the Internet.

NOTE

The security mode and encryption configured on a Wi-Fi terminal must be the same as those of an ONT. If you

cannot find the following encryption modes: TKIP&AES, and AES. The reason may lie in an old Wi-Fi driver

version. If so, replace the old version with a new one.

3.6 Operation Guide on the XML Configuration File

This topic describes how to issue the XML configuration files on the Web page and on the

U2000.

The ONT voice service and gateway involve a large amount of configuration information, most

of which is not defined in the OMCI protocol and cannot be configured on the Web page or the

U2000. Issuing the XML configuration file functions as a supplement to completing all ONT

configurations.

EchoLife HG8240/HG8245/HG8247 GPON Terminal

Service Manual

3 Configuration

Issue 04 (2011-01-12)

Huawei Proprietary and Confidential

3-231

Page 270 / 358

CAUTION

l

Web interface and the U2000 cannot use the same XML configuration file. The XML

configuration file of Web interface contains all configuration data, while the XML

configuration file of the U2000 contains only part of the configuration data.

l

H.248 and SIP can share the same XML configuration file, but the configurations involving

voice service need to be re-configured accordingly.

l

The XML configuration file is generally exported for modifying, and then imported back.

Configuration rolls back or even factory defaults are restored if an incorrect XML

configuration file is imported. When configuration parameters of an XML configuration file

need to be modified, please contact Huawei technical engineers for help.

3.6.1 Operation Guide on the XML Configuration File (on the Web Page)

This topic describes how to issue the XML configuration file on the Web page.

3.6.2 Operation Guide on the XML Configuration File (on the U2000)

This topic describes how to issue the XML configuration files on the U2000.

3.6.1 Operation Guide on the XML Configuration File (on the Web

Page)

This topic describes how to issue the XML configuration file on the Web page.

Prerequisite

You have established the environment for logging in to the Web page for service configuration

and have successfully logged in to the Web page. For details, see

3.4.3 Locally Logging in to

the Web Interface

.

Procedure

Step 1

Export the XML configuration file.

1.

In the navigation tree, choose

System Tools

>

Configuration File

.

2.

In the details area, click

Download Configuration File

, as shown in the following figure.

3 Configuration

EchoLife HG8240/HG8245/HG8247 GPON Terminal

Service Manual

3-232

Huawei Proprietary and Confidential

Issue 04 (2011-01-12)

Rate

Popular Huawei Models

Famous Router IPs

Famous Router Companies

Bookmark Our Site

Share