1. Home
    2. /
  2. Manuals
    3. /
  3. Huawei
    4. /
  4. HG8245H Orange
    5. /
  5. 12
Page 56 / 232 Scroll up to view Page 51 - 55
Figure 3-16
WI-FI Configuration
2.
Click
Apply
.
Table 3-5
describes the basic Wi-Fi parameters.
Table 3-5
Basic Wi-Fi parameters
Parameter
Description
Enable WLAN
Indicates whether to enable the wireless network. The following
parameters can be set only when the wireless network is enabled.
SSID
Indicates the name of the wireless network. It is used to
differentiate different wireless networks. It consists of a
maximum of 32 characters, without space or Tab character.
Associated Device
Number
Specifies the number of STAs. It ranges from 1 to 32.
3 Configuration Guide
EchoLife HG8240/HG8245/HG8247 GPON Terminal
Service Manual
3-18
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
Issue 02 (2011-01-26)
Page 57 / 232
Parameter
Description
Hide Broadcast
Indicates whether to enable or hide broadcast.
l
If the option box is not selected, it indicates that the SSID
broadcast function is enabled. The ONT periodically
broadcasts the SSID, that is, the name of the wireless
network. In this way, any STA can search for the wireless
network.
l
If the option box is selected, it indicates that the SSID
broadcast function is disabled. The SSID is hidden, and the
STA cannot search for the wireless network. The SSID can
be obtained only through a request.
WMM Enable
Indicates whether to enable the QoS of the wireless network.
After the function is enabled, the video and voice QoS can be
improved.
Authentication Mode
Indicates the authentication mode for the STA to request access
to the wireless network. The mode can be Open, Shared, WPA
Pre-Shared Key, WPA2 Pre-Shared Key, WPA Enterprise,
WPA2 Enterprise, or Wi-Fi Protected Setup.
It is set to open by default, that is, the STA can access the network
without authentication.
Encryption Mode
Indicates the encryption mode for the STA to request access to
the wireless network. The encryption mode and encryption
parameters vary with the authentication mode.
l
If the authentication mode is set to
Open
, the encryption
mode can be set to
None
or
WEP
.
l
If the authentication mode is set to
Shared
, the encryption is
WEP
.
l
If the authentication mode is set to
WPA Pre-Shared Key
,
WPA2 Pre-Shared Key
,
WPA Enterprise
, or
WPA2
Enterprise
, the encryption mode can be set to
AES
,
TKIP
,
or
TKIP&AES
.
l
If the authentication mode is set to
Wi-Fi Protected Setup
,
WPS Mode
must be set to
Pin
or
Push-button
.
NOTE
l
Pin
indicates the pin-based encryption.
l
Push-button
indicates the push-button-based encryption.
When
WPS Mode
is set to
Push-button
, press the
WPS
button on
the ONT and press the WPS icon included with the STA within two
minutes, or run the WPS setup program in the STA to install the WPS
software.
3.3.5 Security
This topic describes how to configure the IP address filter, MAC address filter, DoS, and ONT
access control through the Web page.
EchoLife HG8240/HG8245/HG8247 GPON Terminal
Service Manual
3 Configuration Guide
Issue 02 (2011-01-26)
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
3-19
Page 58 / 232
IP Filter Configuration
1.
Click the
Security
tab and then choose
IP Filter Configuration
from the navigation tree.
In the pane on the right, enable the IP address filter function. After selecting the filter mode,
click
New
. Then, in the dialog box that is displayed, configure the rule for filtering IP
addresses from the WAN interface to the LAN port, as shown in
Figure 3-17
.
Figure 3-17
IP Filter Configuration
2.
Click
Apply
.
The IP address filter function is a security mechanism configured on the residential gateway. It
enables or disables all or partial ports in an Intranet IP address segment to communicate with
all or partial ports in an Extranet IP address segment. The IP address filter configuration is used
to limit communication between an Intranet device and an Extranet device.
Table 3-6
describes the parameters related to the IP address filter.
Table 3-6
Parameters related to the IP address filter
Parameter
Description
IP address filter function
Indicates whether to enable the IP address filter function by
clicking
OPEN
or
CLOSE
.
Filter Mode
Indicates the IP address filter rule of the blacklist or whitelist.
l
Blacklist: indicates that the data meeting the rule in the filter
rule list is not allowed to pass.
l
Whitelist: indicates that the data meeting the rule in the filter
rule list is allowed to pass.
The filter mode is global config mode. Thus, the blacklist and
whitelist mode cannot be used at the same time.
3 Configuration Guide
EchoLife HG8240/HG8245/HG8247 GPON Terminal
Service Manual
3-20
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
Issue 02 (2011-01-26)
Page 59 / 232
Parameter
Description
Protocol
Indicates the type of the protocol, which may be TCP/UDP,
TCP, UDP, ICMP, or ALL.
LAN-side IP Address
Indicates the IP address on the LAN side.
LAN-side Port
Indicates the port ID on the LAN side. This parameter can be
configured when
Protocol
is set to
TCP/UDP
,
TCP
or
UDP
.
WAN-side IP Address
Indicates the IP address on the WAN side.
WAN-side Port
Indicates the ID of the WAN side port. This parameter can be
configured when
Protocol
is set to
TCP/UDP
,
TCP
or
UDP
.
MAC Filter Configuration
1.
Click the
Security
tab and then choose
MAC Filter Configuration
from the navigation
tree. In the pane on the right, after enabling MAC filter and selecting the filter mode, click
New
. On the dialog box that is displayed, configure the MAC filter rule for the PC to access
the Internet, as shown in
Figure 3-18
.
Figure 3-18
MAC Filter Configuration
2.
Click
Apply
.
The MAC address lists of PCs in the network are saved on the ONT. Configuring MAC filter
rules enables the PCs that conform to the rules to access the Internet service or disables the PCs
that do not conform to the rules to access the Internet service. A PC may have more than one IP
addresses but a unique MAC address. Therefore, configuring MAC filter rules effectively
controls the Internet service access rights of PCs in a LAN.
Table 3-7
describes the parameters related to the MAC filter.
EchoLife HG8240/HG8245/HG8247 GPON Terminal
Service Manual
3 Configuration Guide
Issue 02 (2011-01-26)
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
3-21
Page 60 / 232
Table 3-7
Parameters related to the MAC address filter
Parameter
Description
MAC address filter function
Indicates whether to enable the MAC address
filter function by clicking
OPEN
or
CLOSE
.
Filter Mode
Indicates the MAC address filter rule of the
blacklist or whitelist.
l
Blacklist: indicates that the data meeting
the rule in the filter rule list is not allowed
to pass.
l
Whitelist: indicates that the data meeting
the rule in the filter rule list is allowed to
pass.
The filter mode is global config mode. Thus,
the blacklist and whitelist mode cannot be
used at the same time.
Source MAC Address
Indicates the source MAC address in the
MAC address filter rule.
URL Filter Configuration
1.
Click the
Security
tab and then choose
URL Filter Configuration
from the navigation
tree. In the pane on the right, after enabling URL filter and selecting the filter mode, click
New
. On the dialog box that is displayed, configure the URL filter rule for the PC to access
the Internet, as shown in
Figure 3-19
.
Figure 3-19
URL Filter Configuration
2.
Click
Apply
.
3 Configuration Guide
EchoLife HG8240/HG8245/HG8247 GPON Terminal
Service Manual
3-22
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
Issue 02 (2011-01-26)

Rate

3.5 / 5 based on 2 votes.

Popular Huawei Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top