Page 6 / 33 Scroll up to view Page 1 - 5
ii
7.2 Ports and Buttons
.....................................................................
23
7.3 Default Settings
........................................................................
25
7.4 Product Specifications
..............................................................
25
Page 7 / 33
1
1 Connecting Cables and Getting Started
Thank you for purchasing the HG658 Home Gateway (HG658 for short).
1.1 Connecting Cables
The following figure shows an example of how to connect the cables. In this
example, the HG658 is connected to a set-top box, desktop computer, laptop
computer, and two telephones.
1
Telephone wall jack
2
Power adapter
3
Splitter
4
HG658
5
Telephone
6
Set-top box
7
Laptop computer
8
Desktop computer
a
LINE port
b
MODEM port
c
PHONE port
Page 8 / 33
2
1.2 Powering On the HG658
After connecting the cables, press the
On/Off
button on the side panel to power
on the HG658.
After you power on the HG658, the
WAN
indicator light blinks (for less than
three minutes), indicating that the HG658 is being activated. Once activated,
the
WAN
indicator light remains steady on. The
Power
indicator also remains
steady on, indicating that the HG658 is working properly.
To power off the HG658, press the
On/Off
button again, and then
unplug the power adapter.
Page 9 / 33
3
2 Setting Network Access Parameters
2.1 Logging in to the Web-based Configuration
Utility
Most parameters of the HG658 are pre-set before delivery to meet common
home application scenarios. To check the HG658's working status or configure
certain advanced network functions, use the web-based configuration utility.
To log in to the web-based configuration utility:
Step 1
Open a browser on your computer. Enter
in the
address box, and then press
Enter
.
Step 2
On the login page, enter your user name (
user
by default) and
password (
HuaweiUser
by default).
For safety or convenience reasons, you can change the user name
and password for the web-based configuration utility. For details,
see section 5.1 “Changing the User Name and Password for the
Web-based Configuration Utility”.
If the user name and password are changed, you must use the new
user name and password to log in.
Step 3
Click
Login
.
After the system verifies your account information, the web-based
configuration utility is displayed.
The first time you log in to the web-based configuration utility, a
setup wizard is displayed. To skip the wizard and go immediately to
the HG658 configuration page, click
Advance
.
Page 10 / 33
4
2.2 Using the Setup Wizard
After logging in to the web-based configuration utility, you can use the
setup wizard to quickly configure the HG658.
When you configure the HG658 for the first time, the setup wizard page is
displayed automatically after logging in to the utility.
If you have configured the HG658 before and you log in to
the web-based configuration utility, the setup wizard page will not be
displayed. However, you can still click
Setup Wizard
in the upper
right corner to display the setup wizard page.
To configure the HG658 through the setup wizard:
Step 1
Log in to the web-based configuration utility. When the
Wizard
page is
displayed, click
Next
.
Step 2
Set
WAN device
based on your network type, enter the user name
and password that are provided by your Internet Service Provider (ISP)
in the
User name
and
Password
text boxes, and then click
Next
.
Step 3
Set WLAN parameters, and then click
Next
.
Step 4
Click
Submit
.
If you can access the Internet without the PPPoE dial-up operation,
skip Step 2 and configure the WLAN parameters directly.
Check the label on the HG658's rear panel for the
SSID
and
WPA
pre-shared key
. You can configure the
SSID
and
WPA
pre-shared key
by choosing
Basic
>
WLAN
. For details, see
section 5.4 "Changing the Wireless Network Name and Password".

Rate

4 / 5 based on 1 vote.

Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top