1. Home
    2. /
  2. Manuals
    3. /
  3. Huawei
    4. /
  4. EchoLife-HG8247
    5. /
  5. 44
Page 216 / 364 Scroll up to view Page 211 - 215
l
Wi-Fi service: Add a GEM port which ID is 3 and bind the GEM port to T-CONT 3.
l
U2560 management channel: Add a GEM port which ID is 4 and bind the GEM port
to T-CONT 4.
NOTE
a.
To change the QoS mode, run the
qos-mode
command to configure the QoS mode to gem-car or flow-
car, and run the
gem add
command to configure the ID of the traffic profile bound to the GEM port.
b.
When the QoS mode is PQ, the default queue priority is 0; when the QoS is flow-car, traffic profile 6
is bound to the port by default (no rate limitation); when the QoS mode is gem-car, traffic profile 6 is
bound to the port by default (no rate limitation).
huawei(config-gpon-lineprofile-10)#
gem add 1 eth tcont 1
huawei(config-gpon-lineprofile-10)#
gem add 2 eth tcont 2
huawei(config-gpon-lineprofile-10)#
gem add 3 eth tcont 3
huawei(config-gpon-lineprofile-10)#
gem add 4 eth tcont 4
Configure the mapping between the GEM port and the ONT-side service to the VLAN
mapping mode (default) and map the service port of CVLAN 20 to the GEM port.
l
HSI service: Map user-side VLAN 10 to GEM port 1.
l
VoIP service: Map user-side VLAN 20 to GEM port 2.
l
Wi-Fi service: Map user-side VLAN 40 to GEM port 3.
l
U2560 management channel: Map user-side VLAN 50 to GEM port 4.
huawei(config-gpon-lineprofile-10)#
mapping-mode vlan
huawei(config-gpon-lineprofile-10)#
gem mapping 1 1 vlan 10
huawei(config-gpon-lineprofile-10)#
gem mapping 2 2 vlan 20
huawei(config-gpon-lineprofile-10)#
gem mapping 3 3 vlan 40
huawei(config-gpon-lineprofile-10)#
gem mapping 4 4 vlan 50
After the configurations are complete, run the
commit
command to make the configured
parameters take effect.
huawei(config-gpon-lineprofile-10)#
commit
huawei(config-gpon-lineprofile-10)#
quit
3.
Configure an ONT service profile.
The ID of the VLAN to which ETH port 1 belongs is 10.
The number of ports configured in the service profile must be the same as the actual number
of ONT ports. The flowing table lists the port capabilities ofHG8010/HG8110/HG8240/
HG8245/HG8247/HG8447. The HG8247 is used as an example.
Product
Number of
ETH Ports
Number of POTS
Ports
Number of CATV
Ports
HG8010
1
-
-
HG8110
1
1
-
HG8240
4
2
-
HG8245
4
2
-
HG8247
4
2
1
HG8447
4
4
1
EchoLife HG8010/HG8110/HG8240/HG8245/HG8247/
HG8447 GPON Terminal
Service Manual
3 Configuration
Issue 02 (2011-12-08)
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
208
Page 217 / 364
NOTE
The
port vlan
command is use for specifying a port VLAN and managing the attribute of the UNI port
on the ONT remotely. This command is applicable for only the L2 service (L2 Internet access service)
when the ONT functions as a bridge device. When the ONT functions as a gateway device, the
configuration of the port VLAN is implemented on the ONT Web page, NMS, or U2560 server.
huawei(config)#
ont-srvprofile gpon profile-id 10
huawei(config-gpon-srvprofile-10)#
ont-port eth 4 pots 2 catv 1
huawei(config-gpon-srvprofile-10)#
port vlan eth 1 10
After the configurations are complete, run the
commit
command to make the configured
parameters take effect.
huawei(config-gpon-srvprofile-10)#
commit
huawei(config-gpon-srvprofile-10)#
quit
4.
(Optional) Configure an alarm profile.
l
The ID of the default GPON alarm profile is 1. The thresholds of all the alarm parameters
in the default alarm profile are 0, which indicates that no alarm is reported.
l
In this example, the default alarm profile is used, and therefore the configuration of the
alarm profile is not required.
l
Run the
gpon alarm-profile add
command to configure an alarm profile, which is used
for monitoring the performance of an activated ONT line.
Step 4
Add an ONT on the OLT.
The ONT is connected to the GPON port of the OLT through optical fibers. The service can be
configured only after an ONT is successfully added on the OLT.
Two ONTs are connected to GPON port 0/1/1. The ONT IDs are 1 and 2, the SNs are
6877687714852900 and 6877687714852901, the management mode is OMCI, and ONT line
profile 10 and service profile 10 are bound to the two ONTs.
1.
Add an ONT offline.
If the password or SN of an ONT is obtained, you can run the
ont add
command to add
the ONT offline.
huawei(config)#
interface gpon 0/1
huawei(config-if-gpon-0/1)#
ont add 1 1 sn-auth 6877687714852900 omci ont-
lineprofile-id 10 ont-srvprofile-id 10
huawei(config-if-gpon-0/1)#
ont add 1 2 sn-auth 6877687714852901 omci ont-
lineprofile-id 10 ont-srvprofile-id 10
2.
Automatically find an ONT.
If the password or SN of an ONT is unknown, run the
port
portid
ont-auto-find
command
in the GPON mode to enable the ONT auto-find function of the GPON port. Then, run the
ont confirm
command to confirm the ONT.
huawei(config)#
interface gpon 0/1
huawei(config-if-gpon-0/1)#
port 1 ont-auto-find enable
huawei(config-if-gpon-0/1)#
display ont autofind 1
//After this command is executed, the information about all ONTs connected
to
the GPON port through the optical splitter is displayed.
------------------------------------------------------------------------
Number
: 1
F/S/P
: 0/1/1
Ont SN
: 6877687714852900
Password
:
VenderID
: HWTC
Ont Version
: 120D0010
Ont SoftwareVersion : V1R002C06
Ont EquipmentID
: 247
Ont autofind time
: 2010-12-10 14:59:10
------------------------------------------------------------------------
EchoLife HG8010/HG8110/HG8240/HG8245/HG8247/
HG8447 GPON Terminal
Service Manual
3 Configuration
Issue 02 (2011-12-08)
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
209
Page 218 / 364
Number
: 2
F/S/P
: 0/1/1
Ont SN
: 6877687714852901
Password
:
VenderID
: HWTC
Ont Version
: 120D0010
Ont SoftwareVersion : V1R002C06
Ont EquipmentID
: 247
Ont autofind time
: 2010-12-10 14:59:12
------------------------------------------------------------------------
huawei(config-if-gpon-0/1)#
ont confirm 1 ontid 1 sn-auth 6877687714852900 omci
ont-lineprofile-id 10 ont-srvprofile-id 10
huawei(config-if-gpon-0/1)#
ont confirm 1 ontid 2 sn-auth 6877687714852901 omci
ont-lineprofile-id 10 ont-srvprofile-id 10
NOTE
If multiple ONTs of the same type are connected to a port and the same line profile or service profile is
bound to the ONTs, you can add ONTs in batches by confirming the auto discovered ONTs in batches to
simplify the operation and increase the configuration efficiency. For example, the preceding command
can be modified as follows:
huawei(config-if-gpon-0/1)#
ont confirm 1 all sn-auth omci ont-lineprofile-id
10 ont-srvprofile-id 10
3.
(Optional) Bind an alarm profile to the ONT.
In this example, bind the default alarm profile, namely alarm profile 1 to the ONT.
huawei(config-if-gpon-0/1)#
ont alarm-profile 1 1 profile-id 1
huawei(config-if-gpon-0/1)#
ont alarm-profile 1 2 profile-id 1
Step 5
Confirm that the ONT goes online normally.
After an ONT is added, run the
display ont info
command to query the current status of the
ONT. Ensure that
Control flag
of the ONT is
active
,
Run State
is
online
,
Config state
is
normal
, and
Match state
is
match
.
huawei(config-if-gpon-0/1)#
display ont info 1 1
---------------------------------------------------------------------
F/S/P
: 0/1/1
ONT-ID
: 1
Control flag
:
active
//Indicates that the ONT is
activated.
Run state
:
online
//Indicates that the ONT goes online
normally.
Config state
:
normal
//Indicates that the configuration status of
the
ONT is normal.
Match state
:
match
//Indicates that the capability profile bound
to
the ONT is consistent with the actual
capability
of the ONT.
...//The rest of the response information is omitted.
If the ONT state fails, the ONT fails to be in the up state, or the ONT does not match, check the
ONT state by referring to the above-mentioned descriptions.
l
If
Control flag
is
deactive
, run the
ont activate
command in the GPON port mode to activate
the ONT.
l
If the ONT fails to be in the up state, that is,
Run state
is
offline
, the physical line may be
broken or the optical transceiver may be damaged. You need to check both the material and
the line.
l
If the ONT state fails, that is,
Config state
is
failed
, the ONT capability set outmatches the
actual ONT capabilities (For details about the ONT actual capabilities, see Reference of
GPON ONT Capability Sets). In this case, run the
display ont failed-configuration
command in the diagnosis mode to check the failed configuration item and the failure cause.
Then, rectify the fault according to actual conditions.
EchoLife HG8010/HG8110/HG8240/HG8245/HG8247/
HG8447 GPON Terminal
Service Manual
3 Configuration
Issue 02 (2011-12-08)
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
210
Page 219 / 364
NOTE
If an ONT supports only four queues, the values of 4–7 of the priority-queue parameter in the
gem add
command are invalid. After configuration recovers, Config state will be failed.
l
If the ONT does not match, that is,
Match state
is
mismatch
, the port types and number of
ports undermatch the actual port types and number of ports supported by the ONT. In this
case, run the
display ont capability
command to query the actual capability of the ONT,
and then select one of the following modes to modify the ONT configuration:
–
Create a proper ONT profile according to the actual capability of the ONT, and then run
the
ont modify
command to modify the configuration data of the ONT.
–
Modify the ONT profile according to the actual capability of the ONT and save the
modification. Then, the ONT automatically recovers the configuration successfully.
Step 6
Specify the native VLAN for the ONT port.
ETH port 1 on the ONT is connected to the PC and the native VLAN is VLAN 10.
NOTE
The
ont port native-vlan
command is used for configuring the native VLAN of an ETH port. When a packet
is transmitted to the ONT, a VLAN tag is added to the packet; when a packet is transmitted out of the ONT, the
VLAN tag is removed from the packet. This command is applicable for only the L2 service (L2 Internet access
service) when the ONT functions as a bridge device. When the ONT functions as a gateway device, the
configuration of the port VLAN is implemented on the ONT Web page, NMS, or U2560 server.
huawei(config-if-gpon-0/1)#
ont port native-vlan 1 1 eth 1 vlan 10
huawei(config-if-gpon-0/1)#
ont port native-vlan 1 2 eth 1 vlan 10
Step 7
Configure traffic profiles.
You can run the
display traffic table ip
command to query the traffic profiles existing in the
system. If the traffic profiles existing in the system do not meet the requirements, you need to
run the
traffic table ip
command to add a traffic profile.
l
HSI service: The profile ID is 8, the CIR is 4 Mbit/s, the priority is 1, and packets are
scheduled according to the priority carried.
l
VoIP service: The profile ID is 9, no rate limitation in the upstream and downstream
directions, the priority is 6, and packets are scheduled according to the priority carried.
l
Wi-Fi service: The profile ID is 10, the CIR is 6 Mbit/s, the priority is 1, and packets are
scheduled according to the priority carried.
l
U2560 management channel: The profile ID is 11, no rate limitation in the upstream and
downstream directions, the priority is 7, and packets are scheduled according to the priority
carried.
huawei(config-if-gpon-0/1)#
quit
huawei(config)#
traffic table ip index 8 cir 4096 priority 1 priority-policy tag-In-
Package
huawei(config)#
traffic table ip index 9 cir off priority 6 priority-policy tag-In-
Package
huawei(config)#
traffic table ip index 10 cir 6144 priority 1 priority-policy tag-In-
Package
huawei(config)#
traffic table ip index 11 cir off priority 7 priority-policy tag-In-
Package
Step 8
Create service ports.
l
HSI service: Set the service port indexes to 1 and 2, SVLAN ID to 100, GEM port ID to 1,
and CVLAN ID to 10. Use traffic profile 8.
l
VoIP service: Set the service port indexes to 3 and 4, SVLAN ID to 200, GEM port ID to 2,
and CVLAN ID to 20. Use traffic profile 9.
EchoLife HG8010/HG8110/HG8240/HG8245/HG8247/
HG8447 GPON Terminal
Service Manual
3 Configuration
Issue 02 (2011-12-08)
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
211
Page 220 / 364
l
Wi-Fi service: Set the service port indexes to 5 and 6, SVLAN ID to 400, GEM port ID to
3, and CVLAN ID to 40. Use traffic profile 10.
l
U2560 management channel: Set the service port indexes to 7 and 8, SVLAN ID to 500,
GEM port ID to 4, and CVLAN ID to 50. Use traffic profile 11.
huawei(config)#
service-port 1 vlan 100 gpon 0/1/1 ont 1 gemport 1 multi-service
user-vlan 10 rx-cttr 8 tx-cttr 8
huawei(config)#
service-port 2 vlan 100 gpon 0/1/1 ont 2 gemport 1 multi-service
user-vlan 10 rx-cttr 8 tx-cttr 8
huawei(config)#
service-port 3 vlan 200 gpon 0/1/1 ont 1 gemport 2 multi-service
user-vlan 20 rx-cttr 9 tx-cttr 9
huawei(config)#
service-port 4 vlan 200 gpon 0/1/1 ont 2 gemport 2 multi-service
user-vlan 20 rx-cttr 9 tx-cttr 9
huawei(config)#
service-port 5 vlan 400 gpon 0/1/1 ont 1 gemport 3 multi-service
user-vlan 40 rx-cttr 10 tx-cttr 10
huawei(config)#
service-port 6 vlan 400 gpon 0/1/1 ont 2 gemport 3 multi-service
user-vlan 40 rx-cttr 10 tx-cttr 10
huawei(config)#
service-port 7 vlan 500 gpon 0/1/1 ont 1 gemport 4 multi-service
user-vlan 50 rx-cttr 11 tx-cttr 11
huawei(config)#
service-port 8 vlan 500 gpon 0/1/1 ont 2 gemport 4 multi-service
user-vlan 50 rx-cttr 11 tx-cttr 11
Step 9
Configure the queue scheduling mode.
Use the 3PQ+5WRR queue scheduling. Queues 0-4 adopt the WRR mode, with the weights of
10, 10, 20, 20, and 40 respectively; queues 5-7 adopt the PQ mode.
NOTE
Queue scheduling is a global configuration. You need to configure queue scheduling only once on the OLT, and
then the configuration takes effect globally. In the subsequent phases, you do not need to configure queue
scheduling repeatedly when configuring other services.
huawei(config)#
queue-scheduler wrr 10 10 20 20 40 0 0 0
Configure the mapping between queues and 802.1p priorities. Priorities 0-7 map queues 0-7
respectively.
huawei(config)#
cos-queue-map cos0 0 cos1 1 cos2 2 cos3 3 cos4 4 cos5 5 cos6 6 cos7
7
For the service board that supports only four queues, the mapping between 802.1p priorities and
queue IDs is as follows: priorities 0 and 1 map queue 1; priorities 2 and 3 map queue 2; priorities
4 and 5 map queue 3; priorities 6 and 7 map queue 4.
Step 10
Save the data.
huawei(config)#
save
----End
Configuration File
vlan 100,200,400,500 smart
vlan attrib 100 stacking
port vlan 100,200,400,500 0/19 0
arp proxy enable
interface vlanif 200
arp proxy enable
quit
dba-profile add profile-id 10 type4 max 102400
dba-profile add profile-id 20 type3 assure 30720 max 102400
dba-profile add profile-id 30 type4 max 204800
dba-profile add profile-id 40 type2 assure 30720
ont-lineprofile gpon profile-id 10
tcont 1 dba-profile-id 10
tcont 2 dba-profile-id 20
tcont 3 dba-profile-id 30
EchoLife HG8010/HG8110/HG8240/HG8245/HG8247/
HG8447 GPON Terminal
Service Manual
3 Configuration
Issue 02 (2011-12-08)
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
212

Rate

3.5 / 5 based on 2 votes.

Popular Huawei Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top