1. Home
    2. /
  2. Manuals
    3. /
  3. Huawei
    4. /
  4. EchoLife-HG556a-v2
    5. /
  5. 5
Page 21 / 59 Scroll up to view Page 16 - 20
3 Quick Start
3-2
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
If y
of the Figure 3-1:
1.
socket.
2.
3.
Connect the phone to the micro-filter with the DSL cable.
3.2 Inse
1.
B stick.
2.
ou have another phone, do as follows refer to the left
Unplug your
telephone
cable from the wall
Connect the micro-filter to the wall socket.
rting the USB Stick
Remove the SIM card holder from the US
Insert the SIM card into the card holder.
3.
Reinsert the SIM card holder into the USB stick.
4.
Remove the lid on the back of the terminal and insert the USB stick into the slot.
The previous USB stick is just the sample for your reference, you can choose other kind of
USB stick that assigned by the Internet Service Provider (ISP) and use the same way to install.
Page 22 / 59
3 Quick Start
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
3-3
3.3 Lo
The terminal
which
you can vi
T
1 lists the PC settings requi
Web-based configuration utility of
t
T
ttings required to l
gging In to the Web-Based Configuration Utility
provides simple and easy Web-based configuration utility, through
ew or configure the working parameters of the terminal.
able 3-
red to log in to the
he terminal.
able 3-1
PC se
og in to the Web-based configuration utility
Item
Requirement
Network protocol
Enable TCP/IP.
PC IP address
o the same network
interface of
By default, the DHCP function is enabled on the
terminal. Therefore, you can configure the PC to
Set the IP address of the PC t
segment as the IP address of the LAN interface of
the terminal.
By default, the IP address of the LAN
the terminal is 192.168.1.1.
obtain an IP address automatically.
Internet Explorer
Do not use the proxy server.
To log in to the Web-based configuration utility, perform the following steps:
Step 1
Sta
e
any
Tak
use
1.
2.
tab in the
Internet Options
dialog box, and then click
LAN
e
Proxy Server
area, ensure that
Use the proxy server for LAN
is cleared. If
N
,
Step 2
p://192.168.1.1
in the address bar of the Internet Explorer, and then press
Enter
Step 3
Enter the administrator account (
User name is admin
and password
is
VF-IRhg55
6
by
e
Login
dialog box, and then click
OK
.
----E
rt the Internet Explorer on the PC and ensure that the Internet Explorer does not us
proxy server.
e Internet Explorer 6.0 as an example. To check that the Internet Explorer does not
any proxy server, perform the following steps:
Start the Internet Explorer. Choose
Tools
>
Internet Options
on the menu bar.
Click the
Connect
Settings
.
3.
In th
Use the proxy server for LAN
is selected, clear
Use the proxy server for LA
and then click
OK
.
Enter
htt
.
default) in th
nd
By default, the IP address of the LAN interface of the terminal is 192.168.1.1. You can change
this IP address. After changing this IP address, ensure that the IP address of the PC is in the
same network segment as the IP address of the LAN interface of the terminal.
Page 23 / 59
4 Configuring the WAN Interface
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
4-1
4
Configuring the WAN Interface
The terminal supports ADSL uplink and HSPA uplink, and you can choose any of the
two modes to access the Internet.
Just keep the default settings, you can access the Internet and do not need to do any
configuration.
4.1 Se
When you select the ADSL uplink mode, the WAN interface of the terminal supports
multiple w
T
mode of the W
lecting ADSL uplink mode
ork modes, as listed in Table 4-1.
able 4-1
Work
AN interface
Work Mode
Description
PPP over ATM (PPPoA)
z
The terminal serves as a router.
z
Data packets use the PPPoA encapsulation mode
PPP over Ethernet (PPPoE)
z
The terminal serves as a router.
z
Dialing is performed through the embedded PPP
dialer software of the terminal.
z
Data packets are encapsulated in PPPoEoA mode.
MAC Encapsulation
Routing (MER)
z
pper-layer DHCP
z
The terminal serves as a router.
z
Data packets use the IPoEoA encapsulation mode.
WAN IP address of the terminal can be a static IP
address or allocated by the u
server automatically.
IP over ATM (IPoA)
ode.
z
The terminal serves as a router.
z
Data packets use the IPoA encapsulation m
Bridge
z
IP address
or is assigned by an upper-layer device.
z
The terminal serves as a network bridge.
z
Dialing is performed through the PPP dialer
software installed on the PC.
The IP address of the computer is a static
Page 24 / 59
4 Configuring the WAN Interface
4-2
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
Table 4-2
the ADSL uplink mode.
T
amet
PVC Configuration
page
lists the information to be collected before configuring
able 4-2
Par
er for the
ATM
Parameter
Description
VPI/VCI
It specifies the VPI and VCI of the PVC. The value is set as 8/35 by
default.
The VPI and VCI of the PVC of the terminal should be consistent
with those of the PVC of the devices on operator networks so that
the connection between the terminal and the devices can be set up
through the PVC.
Service
Category
z
z
z
z
ll
riable rate
It specifies the traffic management type used by the PVC.
UBR Without PCR
: It refers to an unspecified bit rate without a
peak cell rate. Since the transmission rate is not specified, the
ATM network tries its best to transmit UBR user information,
which is called the best effort. In this case, however, the
transmission quality cannot be ensured. For example, the cell
loss and the delay and jitter of cell transmission may occur. This
type is applicable when an end-to-end fault tolerance mechanism
or protocol exists at an upper layer and when no stringent
requirement is imposed on the network transmission capability.
z
UBR With PCR
: It refers to an unspecified bit rate with a peak
cell rate.
CBR
: It refers to a constant bit rate. Fixed requirements are
imposed on the bandwidth (rate). This type is applicable to
real-time transmission of audio and video signals.
Non Realtime VBR
: It refers to a non-real-time variable bit rate.
No stringent requirement is imposed on the cell delay. For
example, when a user retrieves the MPEG-2 video from the
video server through the ATM network, seconds of network
delay does not affect the video quality. You should set
transmission rates, such as the PCR and the SCR, on the
network, thus reducing the cell loss rate.
Realtime VBR
: It refers to a real-time variable bit rate. The ce
delay is restricted stringently. This type is mainly used for
real-time services, such as the video output by a va
encoder, video monitoring, and compressed voice
communication.
Connection
al
type
It specifies the protocol used by the PVC. You should select the
protocol that meets the requirements of the DSLAM. The option
protocols vary with the working mode of the PVC.
Encapsulation
Mode
It specifies the packet encapsulation mode. It is ass
Internet Service Provider.
igned by the
Enable 802.1q
It specifies whether to enable the VLAN function.
Page 25 / 59
4 Configuring the WAN Interface
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
4-3
4.1.1
Figure 4-1
Configuring the PPPoA Mode
To configure the PPPoA mode for the WAN interface, do as follows
Step 1
Logging in to the Web-based configuration utility. For details, see section 3.3 "Logging
In to the Web-Based Configuration Utility."
Step 2
Choose
Advanced Setup
>
WAN
in the navigation tree.
Step 3
Select
ADSL Uplink
.
Step 4
Click
Next
to show the
Wide Area Network (WAN) Setup
page.
Wide Area Network (WAN) Setup
page
Step 5
Click
Add
to show the
ATM PVC Configuration
page, set the parameters refer to
Table 4-2.
Figure 4-2
ATM PVC Configuration
page

Rate

4 / 5 based on 1 vote.

Popular Huawei Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top