Huawei Echolife-HG520b Router Manual PDF (Setup & Configuration Guide)

Page 21 / 33 Scroll up to view Page 16 - 20

13

(3)

In the WAN configuration page, select the

PVC

that needs to

be configured.

(4)

Set

Mode

to

Routing

and

set

Encapsulation

to

PPPoA

.

(5)

Configure the relevant parameters according to the values in

the Table 3-3.

(6)

Fill in the username and the password (provided by the ISP).

(7)

Click

Submit

.

2. Configuring Your Computer

Configure the network card for your computer, to enable the computer

to automatically obtain information such as the IP address and the

gateway.

3.4

Configuring the IPoA Mode

This section describes the process to configure the HG520b in the

IPoA mode and the process to configure your computer to access the

Internet through the HG520b.

3.4.1

Preparation

Table 3-4 shows the configuration for the IPoA mode.

Table 3-4 Configuration for the IPoA mode

Name

Configuration

VPI/VCI

Provided by the ISP

Mode

Routing

Encapsulation

IPoA

IP Address

There are two methods to obtain IP

Address:

z

Obtain default gateway automatically

z

Use the static IP address

Page 22 / 33

14

3.4.2

Steps

1. Configuring the HG520b

Follow the steps described as follows:

(1)

Log in to the Web configuration page. For the procedure,

refer to "2.3

Establishing Configuration Environment."

(2)

Select

Basic

>

WAN Setting

in the navigation tree to

display the WAN configuration page.

(3)

In the WAN configuration page, select the

PVC

that needs to

be configured.

(4)

Set

Mode

to

Routing

.

(5)

Select

Obtain

an

IP

Address

Automatically

or

Static

IP

Address

. Configure the relevant parameters according to

the values in the Table 3-4.

(6)

Click

Submit

.

2. Configuring Your Computer

Configure the network card for your computer, to enable the computer

to automatically obtain information such as the IP address and the

gateway.

3.5

Configuring the RFC2684B Mode

Configuring the RFC2684B mode is similar to configuring the mode

IPoA. For details, refer to 3.4

"Configuring the IPoA Mode."

3.6

Configuring the PPPoE mode

In the PPPoE mode, the HG520b uses the embedded PPP dial-up

software for dialing.

Configuring the PPPoE mode is similar to configuring the PPPoE mode.

The only difference is that you have to select

PPPoE

in the

Encapsulation

to configure PPPoE. For details, refer to 3.3

"Configuring the PPPoA Mode."

Page 23 / 33

15

3.7

Configuring the Wireless Mode

In the Wireless mode, the HG520b makes you access the Internet

without connecting a cable.

This section describes the process to configure the HG520b to work in

the Wireless mode and the process to configure your computer to

access the Internet through the HG520b.

3.7.1

Preparation

Table 3-5 shows the configuration for the Wireless mode.

Table 3-5 Configuration for the Wireless mode

Name

Configuration

Acess Point

Enable

Authentication Type

There are three types:

z

WEP

z

WPA-PSK

z

WPA2-PSK

WPA Encryption

There are two types (found in the

authentication type of

WPA-PSK/WPA2-PSK):

z

TKIP

z

AES

802.11b/g

There are three types:

z

802.11b

z

802.11g

z

802.11b/g

3.7.2

Steps

Follow the steps described below:

(1)

Log in to the Web configuration page. For the procedure,

refer to "2.3

Establishing Configuration Environment."

Page 24 / 33

16

(2)

Select

Basic

>

Wireless LAN

in the navigation tree to

display the Wireless configuration page.

(3)

In the Wireless configuration page, enable wireless and

configure the relevant parameters according to the values in

Table 3-5.

(4)

Select one of the

Authentication Type

. And configure the

relevant parameters.

(5)

Click

Submit

.

Page 25 / 33

17

Chapter 4

Other Settings

4.1

Changing the IP Address of the LAN of the

HG520b

You can access the Web configuration page of the HG520b through

the IP address of the LAN of the HG520b. The IP address of the LAN of

the HG520b is configured by default, you can change it as follows:

(1)

Log in to the Web configuration page of the HG520b. For the

procedure, refer to "2.3

Establishing Configuration

Environment."

(2)

Select

Basic

>

LAN Setting

in the navigation tree to display

the LAN Setting configuration page.

(3)

Enter the IP address and the subnet mask in this page.

(4)

Click

Submit

.

±

Note:

z

You need to log in again to use the Web configuration page after

configuring the IP address of the HG520b.

z

Ensure that the IP address of the computer and the IP address of

the HG520b are in the same network segment, then you can access

the Web configuration page.

4.2

Changing the Administrator Password

The Web manager of the HG520b provides the password protection

function to prevent illegal users from changing the configuration of the

HG520b. The username and the password of the HG520b are

Rate

Popular Huawei Models

Famous Router IPs

Famous Router Companies

Bookmark Our Site

Share