Page 16 / 33
Scroll up to view Page 11 - 15
8
Chapter 3
Service Configuration
This chapter introduces the method for configuring the HG520b.
±
Note:
The figures in the following configuration operations are only for your
reference.
3.1
Service Modes of the HG520b
The HG520b supports multiple service modes and the configuration of
the DSLAM at the office end should be considered when you select a
service mode. Table 3-1 lists the service modes of the HG520b.
Table 3-1 Service modes of the HG520b
Service Mode
Working Method
Configuration
Bridge
z
Take the HG520b as bridge
equipment.
z
Use the PPPoE dial-up software
of the computer for dialing.
Refer to 3.2
"Configuring
the Bridge
Mode."
PPPoA
z
Take the HG520b as a router.
z
Use the PPPoA dial-up software
of the HG520b for dialing.
z
Use the PPPoA encapsulation
mode
to
encapsulate
the
packets.
Refer to 3.3
"Configuring
the PPPoA
Mode."
Page 17 / 33
9
Service Mode
Working Method
Configuration
IPoA
z
Take the HG520b as a router.
z
The HG520b uses the static
public IP address to access the
Internet.
z
Use
the
IPoA
encapsulation
mode
to
encapsulate
the
packets.
Refer to 3.4
"Configuring
the IPoA
Mode."
RFC2684B
z
Take the HG520b as a router.
z
Use the static IP address or the
IP address dynamically allocated
by the ISP.
z
Use
the
IPoE/IPoA
encapsulation
mode
to
encapsulate the packets.
Refer to 3.5
"Configuring
the RFC2684B
Mode."
PPPoE
z
Take the HG520b as a router.
z
Use
the
embedded
PPPoE
dial-up software of the HG520b
for dialing.
z
Use the PPPoE encapsulation
mode
to
encapsulate
the
packets.
Refer to 3.6
"Configuring
the PPPoE
mode."
Note:
ISP = Internet Service Provider
IPoA = Internet Protocol over ATM
PPPoE = PPP over Ethernet
PPPoA = PPP over ATM
Caution:
Some parameters are validated only after they are saved and the
HG520b is rebooted. Follow the prompt in the configuration page to
perform this operation.
Page 18 / 33
10
3.2
Configuring the Bridge Mode
In the bridge mode, the HG520b serves as a bridge. You need to install
the Point to Point Protocol (PPP) dial-up software to realize the dial-up
access to the Internet.
This section describes the process to configure the HG520b to work in
the bridge mode and the process to configure your computer to access
the Internet through the HG520b.
3.2.1
Preparation
Table 3-2 shows the configuration for the bridge mode.
Table 3-2 Configuration for the bridge mode
Name
Configuration
Mode
Bridge
VPI/VCI
Provided by the ISP
PPP dial-up software
Install the PPP dial-up software on your
computer to access the Internet (The
Windows XP operating system is provided
with the PPP dial-up software)
Username and password for
the PPPoE dial-up
Provided by the ISP
Note:
VPI =
Virtual Path Identifier
VCI =
Virtual Channel Identifier
3.2.2
Steps
Configure the following equipment:
z
The HG520b
z
Your computer
Page 19 / 33
11
1. Configuring the HG520b
Follow the steps:
(1)
Log in to the Web configuration page of the HG520b. For the
procedure, refer to "2.3
Establishing Configuration
Environment."
(2)
Select
Basic
>
WAN Setting
in the navigation tree to
display the WAN configuration page.
(3)
In the WAN configuration page, select the
PVC
that needs to
be configured.
(4)
Set
Mode
to
Bridge
. Configure relevant parameters
according to the values in the Table 3-2.
(5)
Click
Submit
.
2. Configuring your computer
After completing the configuration of the HG520b, you need to install
the PPP dial-up software to access the Internet.
The Windows XP (Professional) operating system has a embedded
PPPoE dial-up software. To set up a dial-up connection in Windows XP
system, do as follows:
(1)
Select
Start
>
All
Programs
>
Accessories
>
Communications
>
Network Connections
.
(2)
Click
Create a new connection
in the displayed page.
(3)
Click
Next
in the
New Connection Wizard
dialog box.
(4)
Select
Connect to the Internet
and click
Next
.
(5)
Select
Set up my connection manually
and click
Next
.
(6)
Select
Connect using a broadband connection that
requires a username and password
and click
Next
.
(7)
Enter the name of the connection. You can name it as you
like. Then click
Next
.
(8)
Select an option from
Anyone's use
or
My use only
and
click
Next
.
Page 20 / 33
12
(9)
Enter the username and password. Then click
Next
.
(10) Click
Finish
.
3.3
Configuring the PPPoA Mode
In the PPPoA mode, the HG520b uses the embedded PPP dial-up
software for dialing. The HG520b serves as a router to connect your
computer to the Internet.
This section describes the process to configure the HG520b to work in
the PPPoA mode and the process to configure your computer to
access the Internet through the HG520b.
3.3.1
Preparation
Table 3-3 shows the configuration for the PPPoA mode.
Table 3-3 Configuration for the PPPoA mode
Name
Configuration
VPI/VCI
Provided by the ISP
Mode
Route and PPPoA
Encapsulation
PPPoA
Username and password for the
PPPoA dial-up
Provided by the ISP
3.3.2
Steps
1. Configuring the HG520b
Follow the steps described as follows:
(1)
Log in to the Web configuration page. For the procedure,
refer to "2.3
Establishing Configuration Environment."
(2)
Select
Basic
>
WAN Setting
in the navigation tree to
display the WAN configuration page.
19216811.live