Page 26 / 77
Scroll up to view Page 21 - 25
User Manual
Aolynk DR811/DR814 ADSL2+Broadband Router
4 Web-based Management
23
●
Click
WAN Setup
in the Main menu and choose the
WAN
tab in the Main Frame
to open the WAN connection configuration page, and then click the
label to open the route configuration page.
●
Click
LAN Setup
in the Main menu and choose the
LAN
tab in the Main Frame to
open the LAN configuration page, and then click the
label to open the
route configuration page.
●
Click
Status
in the Main menu and choose the
Status
tab in the Main Frame to
open the status page, and then click the
label to open the route
configuration page.
Figure 4-10
Routes configuration
This page allows you to:
●
View the information about existing routes.
●
Edit a route present in the route list.
●
Add a new route to the DNS relay's list.
●
Delete a present route.
This page lists the following information about existing routes:
●
Whether the route is valid
or invalid
.
●
Destination IP address.
●
Gateway address.
●
Netmask.
●
Whether the route is advertised via RIP (true or false)
To edit the destination address, gateway address, netmask and advertise status of a
route, click in the relevant text box, update the information then click the
button.
To edit the cost or interface settings for the route, click the
label to
open the web page
advanced setting
.
Page 27 / 77
User Manual
Aolynk DR811/DR814 ADSL2+Broadband Router
4 Web-based Management
24
Figure 4-11
Advanced setting of routes
Update the relevant values of route options, and then click the
button.
To delete an existing route item, check the corresponding check box
and click the
button.
To add a new route item, click the
label to open the web page
IP
V4Route
. Enter the values of route options, and then click the
button. Click the
button to abort this action and return to the route configuration page.
Figure 4-12
Create routes
Page 28 / 77
User Manual
Aolynk DR811/DR814 ADSL2+Broadband Router
4 Web-based Management
25
&
Note:
For DHCP or fixed IP service, the address of the next hop must be entered in the
Gateway
box (the box must not be left blank), while Interface can be the default
None
or any other value. For other services (i.e. IPoA, PPPoA, PPPoE), either
Interface
or
Gateway
must be specified with a value; if both of them are configured, only
Interface
takes effect.
4.7 Security Interface
Click
Security
in the Main menu and select the
Interface
tab in the Main Frame to
open the
Security Interface Configuration
page.
Figure 4-13
Security interface
This page allows you to:
●
Enable/disable the security.
●
Enable/disable the firewall.
●
Enable/disable the intrusion detection.
●
Assign the security level.
●
Add/delete a security interface.
●
Enable/disable NAT to internal interfaces.
●
NAT configuration.
To enable/disable the firewall, click the radio button
labeled
Enabled/Disabled
corresponding to
Firewall
, then click the
button.
To enable/disable the intrusion detection, click the radio button
labeled
Enabled/Disabled
corresponding
to
I
ntrusion
Detection
,
then
click
the
button.
Page 29 / 77
User Manual
Aolynk DR811/DR814 ADSL2+Broadband Router
4 Web-based Management
26
To enable/disable the security, click the radio button
labeled
Enabled/Disabled
corresponding to
Security
, then click the
button.
&
Note:
Firewall, intrusion detection and NAT can only be enabled if security is enabled.
Firewall, intrusion detection and NAT must be disabled if security is disabled.
The security level drop-down list contains entries defined as below, in which
None
level
indicates that Internet users are not allowed to access the intranet,
High
level indicates
that Internet users have part of the intranet services-access authority,
medium
level
indicates even higher authority, and
Low
level indicates the highest authority. To set the
proper security level, position the cursor over the entry and left-click to select it, and
then click the
button.
&
Note:
Firewall must be enabled before security level can be configured.
To add a new security interface, click the
label to open the web page
Add
Interface
. Make sure that you have created a virtual interface before doing so. Refer to
4.4
LAN Setting for the way to create a virtual interface.
Figure 4-14
Security
–
add interface
Page 30 / 77
User Manual
Aolynk DR811/DR814 ADSL2+Broadband Router
4 Web-based Management
27
Click on the
Name
drop-down list and select the LAN service that you want to base
your security interface on. Only IP interfaces that have not been assigned a security
type are displayed.
Click on the
Interface Type
drop-down list and specify what kind of interface it is
depending on, that is, how it connects to the network: external, internal or DMZ.
Click the
button. The Security page is displayed, The
Security Interfaces
table
displays information about each existing security interface, including the interface that
you have just configured.
To delete a present security interface, click the corresponding
label to
open the web page
Delete Interface
, and click the
button.
Figure 4-15
Security
–
delete interface
If the NAT is currently disabled, you may click the
button to enable it. If the NAT is currently
enabled, you may click the
button to
disable it.
To perform advanced NAT configuration, click the
label to
open the web page
Advanced NAT Configuration
. If needed, modify the
Global
Address Pools
and
Reserved Mappings
configurations.
19216811.live