Page 26 / 136
Scroll up to view Page 21 - 25
17
Input ‘ipconfig’, then press ‘Enter’ key. Please check the IP address
followed by ‘Default Gateway’ (In this example, the IP address of router
please note that this value may be different.
)
3. Connect the router’s management interface by web browser
After your computer obtained an IP address from router, please start your
web browser, and input the IP address of router in address bar. The
following message should be shown:
Please input user name and password in the field respectively, default
user name is ‘admin’, and default password is ‘1234’, then press ‘OK’
button, and you can see the web management interface of this router:
NOTE: If the IP address of Gateway is not displayed, or the address followed
by ‘IP Address’ begins with ‘169’, please recheck network connection
between your computer and router, and / or go to the beginning of this
chapter, to recheck every step of network setup procedure.
Page 27 / 136
18
NOTE: If you can’t see the web management interface, and you are
being prompted to input user name and password again, it means you
didn’t input username and password correctly. Please retype user
name and password again. If you are certain that user name and
password you typed are correct, please go to ‘4-2 Troubleshooting’ to
perform a factory reset, to set the password back to default value.
TIP: This page shows the major setting categories: Setup, Wireless,
Local Network, Security, Apps and Gaming, Admin, and Status. You
can find the shortcut which leads to these setting categories at the
top of every page, and you can jump to another category directly by
clicking the link.
Page 28 / 136
19
2-3 Using ‘Quick Setup’
This router provides a ‘Quick Setup’ procedure, which will help you to
complete all required settings you need to access the Internet in very short
time. Please follow the following instructions to complete the ‘Quick
Setup’:
Please go to Quick Setup Wizard menu by clicking ‘Setup’ button.
Page 29 / 136
20
And the following message will be displayed:
1. Set Time Zone
Here are descriptions of every setup items:
Set Time
Please press
button, a drop-down list
Zone (1):
will be shown, and you can choose a time zone of the
location you live.
Time Server Address (2): Input the IP address / host name of time server here.
Daylight
If the country you live uses daylight saving,
Savings(3):
please check ‘Enable Function’ box, and choose the duration
of daylight saving.
After you finish with all settings, please click ‘Next’ (4) button.
1
2
3
4
NOTE: There are several time servers available on internet:
129.6.15.28 (time-a.nist.gov)
132.163.4.101 (time-a.timefreq.bldrdoc.gov)
131.107.1.10 (time-nw.nist.gov)
If you found that the time of router is incorrect, try another time server.
Page 30 / 136
2. Broadband Type
Please choose the broadband (Internet connection) type you’re using and
then click ‘Next’. There are six types of Internet connection, they are:
Cable Modem
- Please go to section 2-3-1
Fixed-IP xDSL
- Please go to section 2-3-2
PPPoE xDSL
- Please go to section 2-3-3
PPTP xDSL
- Please go to section 2-3-4
If you’re not sure, please contact your Internet service provider. A wrong
Internet connection type will cause connection problems, and you will not
be able to connect to internet.
If you want to go back to previous step, please press ‘Back’ button on the
bottom of this page.
NOTE: Some service providers use ‘DHCP’ (Dynamic Host Configuration Protocol)
to assign IP address to you. In this case, you can choose ‘Cable Modem’ as Internet
connection type, even if you’re using another connection type, like xDSL. Also,
some cable modem uses PPPoE, so you can choose ‘PPPoE xDSL’ for such cable
modem connections, even if you’re using a cable modem.
19216811.live