Hawking HWRN1A Router Manual PDF (Setup & Configuration Guide)

Page 101 / 138 Scroll up to view Page 96 - 100

92

Here are descriptions of every setup items:

Enable Virtual

Check this box to enable virtual server,

Server (1):

and uncheck this box to disable virtual server.

Private IP (2):

Input the IP address of the computer which

provides Internet service.

Computer Name (3): Pull down the menu and all the computers

connected to the router will be listed here. You can

easily to select the computer name without checking

the IP address of the computer.

Private Port (4):

Input the port number of the IP address

which provides Internet service.

Type (5):

Select the type of connection, TCP or UDP. If you’re

not sure, please select ‘Both’.

Public Port (6):

Please select the port number of Internet IP address

which will be redirected to the port number of local

IP address defined above.

Comment (7):

Please input any text to describe this mapping, up to

1

2

3

4

5

8

9

10

11

12

13

14

7

6

Page 102 / 138

93

16 alphanumerical characters.

Add (8):

Add the mapping to virtual server table.

Reset (9):

Remove all inputted values.

Virtual Server

All existing virtual server mappings will be

Table (10):

displayed here.

Delete

Please select a virtual server mapping by clicking

Selected (11):

the ‘Select’ box of the mapping, then click ‘Delete

Selected’ button to remove the mapping. If there’s no

existing mapping, this button will be grayed out.

Delete All (12):

Delete all mappings existed in virtual server table.

Reset (13):

Unselect all mappings.

After you finish with all settings, please click ‘Apply’ (14) button and the

following message will be displayed on your web browser:

Please click ‘Continue’ to go back to previous setup menu; to continue on

other setup procedures, or click ‘Apply’ to reboot the router so the

settings will take effect (Please wait for about 30 seconds while router is

rebooting).

If you want to reset all settings in this page back to previously-saved

value, please click ‘Cancel’ button.

Page 103 / 138

94

3-2-4 Port Mapping for Special Applications

Some applications require more than one connection at a time; these

applications won’t work with simple NAT rules. In order to make these

applications work, you can use this function to let these applications work.

Go to ‘Apps and Gaming’ and click ‘Special Applications’.

Here are descriptions of every setup items:

Enable (1):

Check this box to enable special applications and

uncheck this box to disable virtual server.

IP Address (2):

Input the IP address of the computer which you

want to open the ports.

Computer Name (3): Pull down the menu and all the computers

connected to the router will be listed here. You can

easily to select the computer name without checking

the IP address of the computer.

TCP Port to Open (4): This is the out going (Outbound) range of TCP

1

2

3

4

5

8

9

10

11

12

7

6

13

14

Page 104 / 138

95

port numbers for this particular application.

UDP Port to Open (5): This is the out going (Outbound) range of UDP

port numbers for this particular application.

Comment (6):

The description of this setting.

Pop. Applications

This section lists the more popular applications that

(7):

require multiple connections. Select an application

from the Popular Applications selection and click

‘Add’ to save the setting to ‘Current Trigger-Port

Table.’

Add (8):

Add the setting to the ‘Current Trigger-Port Table.’

Reset (9):

Click ‘Reset’ will clear all above setting and you

can set up again.

Current Trigger-Port All the settings for the special applications will be

(10):

listed here. If you want to remove some Special

Application settings from the " Current Trigger-Port

Table", select the Special Application settings you

want to remove in the table and then click "Delete

Selected". If you want remove all Special

Appliacation settings from the table, just click

"Delete All" button. Click "Reset" will clear your

current selections.

Delete

Please select a special application by clicking

Selected (11):

the ‘Select’ box of the mapping, then click ‘Delete

Selected’ button to remove the setting. If there’s no

setting here, this button will be grayed out.

Delete All (12):

Delete all settings existed in trigger port table.

Reset (13):

Unselect all settings.

Page 105 / 138

96

Note: Only one LAN client can use a particular special application at a

time.

After you finish with all settings, please click ‘Apply’ (14) button and the

following message will be displayed on your web browser:

Please click ‘Continue’ to go back to previous setup menu; to continue on

other setup procedures, or click ‘Apply’ to reboot the router so the

settings will take effect (Please wait for about 30 seconds while the router

is rebooting).

If you want to reset all settings in this page back to previously-saved

value, please click ‘Cancel’ button.

3-2-5 UPnP Setting

This function enables network auto-configuration for peer-to-peer

communications, with this function, network devices will be able to

communicate with other devices directly, and learn about information

about other devices. Many network device and applications rely on UPnP

function nowadays.

Please click ‘Apps and Gaming’ at top of web management interface,

then click ‘UPnP’, and the following message will be displayed on your

web browser:

Rate

Popular Hawking Models

Famous Router IPs

Famous Router Companies

Bookmark Our Site

Share