Hawking HW2R1 Router Manual PDF (Setup & Configuration Guide)

Page 101 / 134 Scroll up to view Page 96 - 100

93

Client PC

Please input the MAC address of computer

MAC address (2):

or network device here, dash ( - ) or colon ( : ) are not

required. (i.e. If the MAC address label of your wireless

device indicates ‘aa-bb-cc-dd-ee-ff’ or

‘aa:bb:cc:dd:ee:ff’, just input ‘aabbccddeeff’

Computer Name (3):

Pull down the menu and all the computers connected to

the Smart Repeater will be listed here. You can easily to

select the computer name without checking the IP

address of the computer.

Comment (4):

You can input any text here as the comment of this

MAC address, like ‘ROOM 2A Computer’ or anything.

You can input up to 16 alphanumerical characters here.

This is optional and you can leave it blank, however, it’s

recommended to use this field to write a comment for

every MAC addresses as a memory aid.

Add (5):

Click ‘Add’ button to add the MAC address and

associated comment to the MAC address filtering table.

Reset (6):

Remove all inputted values.

MAC Filtering

All existing MAC addresses in filtering table

Table (7):

will be listed here.

Delete Selected (8): If you want to delete a specific MAC address entry,

check the ‘select’ box of the MAC address you want to

delete, then click ‘Delete Selected’ button. (You can

select more than one MAC addresses).

Delete All (9):

If you want to delete all MAC addresses listed here,

please click ‘Delete All’ button.

Reset (10):

You can also click ‘Reset’ button to unselect all MAC

addresses.

Enable IP

Check this box to enable IP address based

Page 102 / 134

94

Filtering Table (11):

filtering, and please select ‘Deny’ or ‘Allow’

to decide the behavior of IP filtering table. If you select

deny, all IP addresses listed in filtering table will be

denied from connecting to the network; if you select

allow, only IP addresses listed in filtering table will be

able to connect to the network, and rejecting all other

network devices.

IP Filtering

All existing IP addresses in filtering table will be

Table (12):

listed here.

Add PC (13):

Click this button to add a new IP address to IP filtering

table, up to 20 IP addresses can be added.

Please refer to section 3-3-1-1 ‘Add PC’ below.

Delete

If you want to delete a specific IP address entry,

Selected (14):

check the ‘select’ box of the IP address you want to

delete, then click ‘Delete Selected’ button. (You can

select more than one IP addresses).

Delete All (15):

If you want to delete all IP addresses listed here, please

click ‘Delete All’ button.

After you finish with all settings, please click ‘Apply’ (16) button and the

following message will be displayed on your web browser:

Press ‘Go Back to save the settings made and go back to the web

management interface; press ‘Apply’ to save the settings made and restart the

Smart Repeater so the settings will take effect after it reboots.

rebooting).

Page 103 / 134

95

If you want to reset all settings in this page back to previously-saved value,

please click ‘Cancel’ button.

3-3-1-1 Add PC

After button is clicked, the following message will be displayed on your web

browser:

a

b

c

d

e

f

Page 104 / 134

96

Here are descriptions of every setup items:

Client PC

Please input any text to describe this IP

Description (a):

address, up to 16 alphanumerical characters.

Client PC IP

Please input the starting IP address in the left

address (b):

field, and input the end IP address in the right field to

define a range of IP addresses, or just input the IP

address in the left field to define a single IP address.

Client PC

Please check all services you want to allow or

Service (c):

deny this IP address to use, you can check multiple

services.

Protocol (d):

If the service you need is not listed above, you can

create a new service on your own. Please select TCP or

UDP, if you’re not sure, please select ‘Both’.

Port Range (e):

Please input the port range of new service here. If you

want to specify port 80 to 90, please input ’80-90’; if you

want to apply this rule on a single port, just input the

port number, like ‘80’.

Add (f):

When you finish with all settings, please click ‘Add’ to

save settings, you’ll be brought back to previous menu,

and the rule you just set will appear in current IP filtering

table.

If you want to remove all settings in this page, click ‘Reset’ button.

Page 105 / 134

97

3-3-2 URL Blocking

If you want to prevent computers in a local network from accessing certain

website (like pornography, violence, or anything you want to block), you can

use this function to stop computers in a local network from accessing the site

you define here.

This function is useful for parents and company managers.

Please follow the following instructions to set URL blocking parameters:

Please click ‘Security’ tab at top of web management interface, then click ‘URL

Blocking’, and the following message will be displayed on your web browser:

Here are descriptions of every setup items:

Enable URL

Check this box to enforce URL Blocking,

Blocking (1):

uncheck it to disable URL Blocking.

1

2

3

4

5

6

7

8

9

Rate

Popular Hawking Models

Famous Router IPs

Famous Router Companies

Bookmark Our Site

Share