GetNet GR-534W Router Manual PDF (Setup & Configuration Guide)

Page 6 / 147 Scroll up to view Page 1 - 5

1

Overview

Thank you for choosing GETNET GR-534W.

GETNET GR-534W is fully compatible with 802.11g standard. Meanwhile, it is also

compatible with 802.11 standards and earlier 802.11b standards. GETNET GR-534W

supports CCK and OFDM and its data rate is up to 150 Mbps. It is easy to install and

can be applied to AP and router access.

GETNET GR-534W provides 64-bit and 128-bit WEP encryption schemes, and WPA

encryption, associating with IEEE 802.1X authentication, which insures the security

of wireless communication.

Package List

Please check whether your package list includes the following items:

°

GR-534W x 1

°

Power adapter x 1

°

RJ 45 cable x 1

Page 7 / 147

2

Hardware Description and Hardware Installation

2.1

Front Panel and LED Status

There are 8 LED indicators on the front panel of GR-534W. By observing their

status, you can judge whether the device runs normally.

The following table describes the LED indicators on the front panel.

LED

Indicator

Color

Status

Description

Red

On

Power is on.

Green

On

The device runs normally.

-

Off

Power is off or the device is down.

Green

On

Radio switch is turned on.

Green

Blink

Data is being transmitted.

-

Off

Radio switch is shut off.

WPS

Green

On

Connection

succeeds

under

Wi-Fi

Protected Setup.

Page 8 / 147

3

Green

Blink

Negotiation is in progress under Wi-Fi

Protected Setup.

-

Off

Wi-Fi Protected Setup is disabled.

WAN

Green

On

Connection succeeds.

Green

Blink

Data is being transmitted.

-

Off

No WAN connection.

LAN

1/2/3/4

Green

On

LAN connection succeeds.

Green

Blink

Data is being transmitted.

-

Off

No LAN connection.

2.2

Rear Panel and Interface Description

The following table describes the interfaces or the buttons on the rear panel:

Interface/Button

Description

RESET

Press the button for 3 seconds and

then release it. System restores the

factory default settings.

ON/OFF

By pressing the button, the power is

on. Press the button again, and then

the power is off.

POWER

Power socket, for connecting the

power adapter.

WAN

WAN interface, for connecting WAN or

the uplink network devices.

LAN1~LAN4

LAN interface, for connecting hub,

switch, or computer on LAN.

WPS

This button is used for enabling WPS

PBC mode. If WPS is enabled, press

this button, and then AP starts to

Page 9 / 147

4

accept the negotiation of PBC mode.

Note:

Do not press the

Reset

button unless you want to clear the current settings. The

Reset

button is in a small circular hole on the rear panel. If you want to restore the

default settings, please press the

Reset

button gently for 3 seconds with a fine

needle inserted into the hole and then release the button. The system reboots and

returns to the factory defaults.

Warning:

The power specification is 12V, 500 mA. If the power adapter does not match the

specification, it may damage the device.

2.3

Hardware Installation

2.3.1

System Requirements

Before installing the device, please make sure that the following items are ready.

°

At least one Ethernet RJ45 cable (10Base-T/100Base-T)

°

GR-534W x 1

°

A PC has been installed PCP/IP protocol and it can access the Internet.

2.3.2

Before You Begin

Before you install the device, please pay attention to the following items:

°

When connecting the device to the computer, hub, router or switch, the

Ethernet cable should be less than 100 meters.

°

Do not place this device on an unstable surface or support. Do not put this

device on the ground.

°

Keep the device clean. Avoid the device from direct sunshine. Avoid any

metal in the device.

°

Place the device in the center of the area, and try to optimize the wireless

coverage.

2.3.3

Connecting AP

Step 1

Connect one end of the RJ45 cable to the LAN interface of the GR-534W.

Step 2

Connect the other end of the RJ45 cable to your PC.

Step 3

Connect the power adapter to the power socket of the GR-534W.

Page 10 / 147

5

2.4

Operation Range

The operation range of GR-534W depends on the actual environment. When the

device is placed in the house or in the office, the overall arrangements are different.

So the path and effect for the signal transmission are different. For example, the

outdoor straight transmission distance for some devices in the open air is up to 300

meters, and the indoor straight transmission distance is up to 100 meters.

2.5

Roaming

Suppose that several GR-534Ws run in the same network. Each GR-534W acts as

one BSS, and has its coverage. One wireless client terminal (e.g. notebook PC or

PDA) can realize roaming from one AP to another AP correctly. In that case, the

wireless client terminal can communicate with the other devices within the

GR-534Ws’ coverage.

In order to realize the wireless client roaming among different GR-534Ws, you need

to set the GR-534W properly. Do as follows:

°

Set the same SSID for different GR-534Ws.

°

The SSIDs of all the computers and PDAs should be consistent with that of

the GR-534Ws.

°

All the BSSs must use the same wireless channel.

°

If the encryption function is enabled, all the GR-534Ws should configure

the same encryption mode and the encryption key for establishing

connection.

°

GR-534W must keep the wireless signal covering the whole operation

environment and the wireless signal should be continuous. Please put the

GR-534Ws to the appropriate places for a better network coverage.

Rate

Popular GetNet Models

Famous Router IPs

Famous Router Companies

Bookmark Our Site

Share