D-Link DVX-1000 Router Manual PDF (Setup & Configuration Guide)

Page 26 / 96 Scroll up to view Page 21 - 25

±µ

D-Link DVX-1000 User Manual

Section ² - Conﬁguration

Gateway Id

- A unique Gateway Id.

Gateway Type

- The type of gateway. It can be INET / PSTN.

Domain Name

- Speciﬁes the domain name / IP address of the Gateway. This is used and the domain name/IP Address

when the call server has to register to the gateway.

Port

- Speciﬁes the port number that the gateway is conﬁgured on.

Conﬁguring Gateways

Gateways are used to connect the DVX-1000 to external SIP-based servers or PSTN networks. The DVX-1000 can

be connected to other SIP servers by conﬁguring the servers as ‘INET’ gateways. The DVX-1000 can connect to a

PSTN network through a ‘PSTN’ gateway. This is not to be confused with the default gateway conﬁgured during system

conﬁguration.

The Gateway conﬁguration information can be viewed by clicking

Call Server

>

Gateways

.

The webpage of the

gateway can be accessed by clicking on the ‘User extension’ ﬁeld. It is assumed that the web-server of the device

uses the standard HTTP port (port 80).

To add a new gateway, click on

Add New

. The following parameters are to be

conﬁgured.

Page 27 / 96

±¶

D-Link DVX-1000 User Manual

Section ² - Conﬁguration

Max Calls Supported

- Limits the number of simultaneous calls through this gateway if a value is entered or allows

unlimited calls, if the checkbox is selected.

Session Refresh Required

- Refreshes the session at regular intervals. The interval is conﬁgurable from the Call

server conﬁguration page.

Outbound Proxy Enabled

- Check this box if the gateway is connected through an outbound proxy.

IP Address

- IP Address of the outbound proxy.

Port

- Port number of the outbound proxy.

Registration Required

- Check this box if DVX-1000 needs to register with the external gateway. If this box is unchecked,

DVX expects the gateway to register to it. In either case, the SIP User extension, Username and Password conﬁgured

below will be used for the registration. i.e. Incoming registrations from the gateway will be authenticated against these

values or Outgoing register requests will be constructed with these values.

SIP User ID -

SIP User extension associated with this gateway. This will be used for Authentication.

User Name

- SIP display name for the gateway user. This will be used for Authentication.

Password

- Speciﬁes the password associated with this gateway. This will be used for authentication.

Note:

The SIP User ID, Username and Password conﬁgured here should be conﬁgured on the gateway for the registrations to work. Please

refer to the User manual of the Gateway for a description on how to do this.

Detecting inactive sessions

Gateway sessions can be refreshed to verify whether they are still active. Selecting ‘Session refresh required’ will enable

this feature for a gateway. All calls through that gateway will then be refreshed by sending SIP requests at regular intervals.

This interval can be conﬁgured from the callserver conﬁguration page. If the gateway or the user agents involved in the

session fail to respond to the session refresh request the call will be torn down. Any activity on the session will reset

the timer for the session refresh request so that the refresh request don’t add to network congestion in case there is

heavy trafﬁc.

Page 28 / 96

±·

D-Link DVX-1000 User Manual

Section ² - Conﬁguration

Conﬁguring Routes

The Route conﬁguration information can be obtained by clicking

Call Server

>

Routes

. To add a New RouteGroup

conﬁguration, click on

Add New

. At least one route should be created and added while creating a RouteGroup. The

Route View Column helps in viewing all the Routes belonging to a RouteGroup.

New Routes can be Added / Deleted / Edited from here. Routes can be moved from one RouteGroup to another by editing

a Route. All Routes except the highest priority Route can be deleted from a RouteGroup. Deletion of a RouteGroup is

possible only if it is not being used by any user.

The following are the route conﬁguration options:

RouteGroupName

- Specify a new unique RouteGroup Name (Max 20 Char).

Page 29 / 96

±¸

D-Link DVX-1000 User Manual

Section ² - Conﬁguration

Duration Paramete

rs - Specify the time for which this Route is valid. All time parameters are mandatory.

Route Name

- Specify a new unique Route Name (Max 20 Char).

DestinationType

- Type of the Route Destination. It can be LOCAL/PSTN/INET.

Destination Id

- Indicates the Gateway Id corresponding to this route. For LOCAL destination type the Gateway Id

does not need to be speciﬁed, hence disabled.

Priority

- Indicates priority of this route in its RouteGroup. The value can be in the range of 1 to 25. Make sure not to

add a priority which is already used.

Min Digits

- Indicates the minimum dial digits for this route.

Max Digits

- Indicates the maximum dial digits for this route.

No of Mask Digits

- Indicates the number of Dial Digits to be masked.

Dialed Digits

- Dialed strings to be matched to select this route entry. A dialed string of ‘*’ matches any string of 0 or

more elements.

Preﬁx

- Preﬁx to be added to the number after masking.

Page 30 / 96

²0

D-Link DVX-1000 User Manual

Section ² - Conﬁguration

The Group conﬁguration information can be viewed by clicking

Call Server

>

Groups

. Groups can be of two types

• UserGroup

• Hunt Group

The user group is speciﬁcally used for determining user privileges during Call Pickup. A particular user can pick up

calls for him on another extension only if that extension belongs to the same user group as him. A new Group can be

added by clicking

Add New

. A unique Id needs to be given to each Group. Group Type distinguishes between a user

group and a hunt group. The mode ﬁeld is relevant only to a hunt group. A hunt group can be conﬁgured in one of four

modes (First Only /Sequential /Parallel/Distributed). Members in a user group are added when the user is actually

added to the call server. Hunt Group members can be added/edited/deleted by clicking the

edit

button in the ‘View

members’ page.

Note:

Each Group (User/Hunt Group) can have a maximum of 20 users. Beyond this a new user group has to be

created to add more users. Also, a user can belong to a maximum of 5 user groups.

Conﬁguring Groups

Rate

Popular D-Link Models

Famous Router IPs

Famous Router Companies

Bookmark Our Site

Share