Page 41 / 120 Scroll up to view Page 36 - 40
37
D-Link DIR-608 User Manual
Section 3 - Configuration
SLAAC/DHCPv6 (continued)
Enable
Autoconfiguation:
Enable or disable the Automatic IPv6 Address Assignment feature.
LAN IPv6 Address:
Select
SLAAC+Stateless DHCP
or
Stateful DHCPv6
.
If you choose
SLAAC+Stateless DHCP
, please configure the following field:
Router
Advertisement
Lifetime:
Enter the IPv6 address lifetime (in minutes).
Address Autoconfiguration Settings
If you choose
Stateful DHCPv6
, please configure the following field:
IPv6 Address
Range(Start):
Enter the starting IPv6 address for the DHCP server’s IPv6 assignment.
IPv6 Address
Range(End):
Enter the ending IPv6 address for the DHCP server’s IPv6 assignment.
Router
Advertisement
Lifetime:
Enter the IPv6 address lifetime (in seconds).
Address Autoconfiguration Settings
Use this section to setup IPv6 Autoconfiguration to assign IP
addresses to the computers on your network.
Enable Autoconfiguration:
LAN IPv6 Address:
Stateful(DHCPv6)
IPv6 Address Range(Start):
xxxx
::00
3
IPv6 Address Range(End):
xxxx
::00
16
Router Advertisement
Lifetime:
(second)
Address Autoconfiguration Settings
Use this section to setup IPv6 Autoconfiguration to assign IP
addresses to the computers on your network.
Enable Autoconfiguration:
LAN IPv6 Address:
SLAAC+Stateless DHCP
Router Advertisement
Lifetime:
30
(minutes)
Page 42 / 120
38
D-Link DIR-608 User Manual
Section 3 - Configuration
PPPoE
My IPv6
Connection is:
Select
PPPoE
if your ISP provides and requires you to enter a PPPoE
username and password in order to connect to the Internet.
IPv6 Connection Type
IPv6 Connection Type:
Choose the mode to be used by the router to the IPv6
Internet.
My IPv6 Connection is:
PPPoE
User Name:
Enter the username provided by your ISP.
Password:
Enter the password provided by your ISP.
Service Name:
Enter the ISP service name (optional).
Idle Time:
Set the connection time out length. (Connect on Demand only)
MTU Size:
Enter the MTU size.
Connection Type:
Select either
Continuous
,
Connect on Demand
, or
Manual
.
PPPoE
Enter the information provided by your Internet Service
Provider (ISP).
User Name:
Password:
Service Name:
Idle Time:
5
(1-1000
minutes)
MTU Size:
1452
Connection Type:
Connect on Demand
connect
disconnect
PPPoE:
If you choose
Use the following DNS address
, please configure the following field:
Primary DNS
Address:
Enter the primary DNS server address.
Secondary DNS
Address:
Enter the secondary DNS server address.
IPv6 DNS Settings
Select either
Obtain DNS server address automatically
or
Use the following DNS address
.
IPv6 DNS Settings
Obtain DNS server address automatically or enter a
specific DNS server address.
Obtain DNS server address
automatically
Use the following DNS
address
Primary DNS Address:
Secondary DNS Address:
Page 43 / 120
39
D-Link DIR-608 User Manual
Section 3 - Configuration
LAN IPv6 Address Settings
Use this section to configure the internal network settings of
your router. If you change the LAN IPv6 Address here, you
may need to adjust your PC’s network settings to access the
network again.
Enable DHCP-PD:
LAN IPv6 Address:
/64
LAN IPv6 Link-Local
Address:
xx00:yy11:zz22:123/64
Enable
Autoconfiguation:
Enable or disable the Automatic IPv6 Address Assignment feature.
LAN IPv6 Address:
Select
SLAAC+Stateless DHCP
or
Stateful DHCPv6
.
If you choose
SLAAC+Stateless DHCP
, please configure the following field:
Router
Advertisement
Lifetime:
Enter the IPv6 address lifetime (in minutes).
Address Autoconfiguration Settings
If you choose
Stateful DHCPv6
, please configure the following field:
IPv6 Address
Range(Start):
Enter the starting IPv6 address for the DHCP server’s IPv6 assignment.
IPv6 Address
Range(End):
Enter the ending IPv6 address for the DHCP server’s IPv6 assignment.
Router
Advertisement
Lifetime:
Enter the IPv6 address lifetime (in seconds).
PPPoE (continued)
Enable DHCP-PD:
Check this box to enable DHCP-PD.
LAN IPv6 Address:
If you disabled DHCP-PD, enter the LAN (local) IPv6 address for the
router.
LAN IPv6 Link-
Local Address:
Displays the router’s LAN link-local address.
LAN IPv6 Address Settings
Address Autoconfiguration Settings
Use this section to setup IPv6 Autoconfiguration to assign IP
addresses to the computers on your network.
Enable Autoconfiguration:
LAN IPv6 Address:
Stateful(DHCPv6)
IPv6 Address Range(Start):
xxxx
::00
3
IPv6 Address Range(End):
xxxx
::00
16
Router Advertisement
Lifetime:
(second)
Address Autoconfiguration Settings
Use this section to setup IPv6 Autoconfiguration to assign IP
addresses to the computers on your network.
Enable Autoconfiguration:
LAN IPv6 Address:
SLAAC+Stateless DHCP
Router Advertisement
Lifetime:
30
(minutes)
Page 44 / 120
40
D-Link DIR-608 User Manual
Section 3 - Configuration
IPv6 Connection Type:
Choose the mode to be used by the router to the IPv6
Internet.
My IPv6 Connection is:
IPv6 In IPv4 Tunnel
IPv6 in IPv4 Tunnel Settings
Enter the IPv6 in IPv4 Tunnel information provided by
your Tunnel Broker.
Remote IPv4 Address:
Remote IPv6 Address:
Local IPv4 Address:
192.168.x.x
Local IPv6 Address:
/
My IPv6
Connection is:
Select
IPv6 In IPv4 Tunnel
if you wish to configure the IPv6
connection to run in IPv4 Tunnel mode. IPv6 over IPv4 tunnelling
encapsulates IPv6 packets in IPv4 packets so that IPv6 packets can
be sent over an IPv4 infrastructure.
IPv6 Connection Type
IPv6 In IPv4 Tunnel
Remote IPv4
Address:
Enter the IPv4 remote address you will use.
Remote IPv6
Address:
Enter the IPv6 remote address you will use.
Local IPv4
Address:
Displays the current local IPv4 address.
Local IPv6 Address
and Subnet Prefix
Length:
Enter the IPv6 local address and subnet prefix length.
IPv6 in IPv4 Tunnel Settings
IPv6 DNS Settings
Obtain DNS server address automatically or enter a
specific DNS server address.
Primary DNS Address:
Secondary DNS Address:
If you choose
Use the following DNS address
, please configure the following field:
Primary DNS
Address:
Enter the primary DNS server address.
Secondary DNS
Address:
Enter the secondary DNS server address.
IPv6 DNS Settings
Select either
Obtain DNS server address automatically
or
Use the following DNS address
.
Page 45 / 120
41
D-Link DIR-608 User Manual
Section 3 - Configuration
LAN IPv6 Address Settings
Use this section to configure the internal network settings of
your router. If you change the LAN IPv6 Address here, you
may need to adjust your PC’s network settings to access the
network again.
LAN IPv6 Address:
/64
LAN IPv6 Link-Local
Address:
xx00:yy11:zz22:123/64
IPv6 In IPv4 Tunnel (continue)
LAN IPv6 Address:
Enter the LAN (local) IPv6 address for the router.
LAN IPv6 Link-
Local Address:
Displays the router’s LAN link-local address.
LAN IPv6 Address Settings
Enable
Autoconfiguation:
Enable or disable the Automatic IPv6 Address Assignment feature.
LAN IPv6 Address:
Select
SLAAC+Stateless DHCP
or
Stateful DHCPv6
.
If you choose
SLAAC+Stateless DHCP
, please configure the following field:
Router
Advertisement
Lifetime:
Enter the IPv6 address lifetime (in minutes).
Address Autoconfiguration Settings
If you choose
Stateful DHCPv6
, please configure the following field:
IPv6 Address
Range(Start):
Enter the starting IPv6 address for the DHCP server’s IPv6 assignment.
IPv6 Address
Range(End):
Enter the ending IPv6 address for the DHCP server’s IPv6 assignment.
Router
Advertisement
Lifetime:
Enter the IPv6 address lifetime (in seconds).
Address Autoconfiguration Settings
Use this section to setup IPv6 Autoconfiguration to assign IP
addresses to the computers on your network.
Enable Autoconfiguration:
LAN IPv6 Address:
Stateful(DHCPv6)
IPv6 Address Range(Start):
xxxx
::00
3
IPv6 Address Range(End):
xxxx
::00
16
Router Advertisement
Lifetime:
(second)
Address Autoconfiguration Settings
Use this section to setup IPv6 Autoconfiguration to assign IP
addresses to the computers on your network.
Enable Autoconfiguration:
LAN IPv6 Address:
SLAAC+Stateless DHCP
Router Advertisement
Lifetime:
30
(minutes)

Rate

3.5 / 5 based on 2 votes.

Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top