57

D-Link DIR-608 User Manual

Section 3 - Configuration

Wireless Repeater

Wireless Repeater

Wireless Repeater

DIR-608

Wireless

Advanc

This page allows you to configure wireless repeater settings for the DIR-608.

Wireless Repeater Setup

Repeater Enabled:

Check the box and click the

Apply

button in order to enable the

Wireless Repeater function. Repeater function is disabled by default.

SSID of AP:

If repeater mode is enabled, the name of the host network that is

being repeated is displayed here.

Click the

Site Survey

button to enable the router to search for nearby

wireless networks. This will take about 5 seconds.

Refer to

Wireless Repeater Setup

on page

58

for instructions on how to enable the

Wireless Repeater Functionality.

Wireless Repeater Setup

☐

Repeater Enabled(

DHCP

mode will be set to ‘none’

if the repeater is enabled

)

SSID of AP

Site Survey

Apply

58

D-Link DIR-608 User Manual

Section 3 - Configuration

Wireless Repeater

Wireless Repeater

DIR-608

Wireless

Advanc

Wireless Repeater Setup

These instructions will guide you through setting up your DIR-608 as a wireless repeater in a

few easy steps. Please refer to Wireless Repeater Mode on page

9

for more information.

Step 1: Navigate to the

Wireless Repeater

section of the web ui, click on the

Wireless

tab

on the top of the web ui and click

Wireless Repeater

from the menu on the left hand side

of the screen.

Wireless Repeater Setup

☑

Repeater Enabled(

DHCP

mode will be set to ‘none’

if the repeater is enabled

)

SSID of AP

Site Survey

#

SSID

MAC Address

Channel

Signal

Security

Select

1

D-Link

ff:ff:ff:ff

1

100%

WPA2-

PSK(TKIP)

Click ‘Next’ to Continue repeater settings

Next

Apply

Wireless Repeater Setup

Repeater Enabled:

Check the box and click the

Apply

button in order to enable the

Wireless Repeater function.

SSID of AP:

Click the

Site Survey

button to enable the router to search for nearby

wireless networks. This will take about 5 seconds.

A list of wireless networks that have been found will then appear.

Select the wireless network you wish to extend and click the

Next

button.

59

D-Link DIR-608 User Manual

Section 3 - Configuration

Wireless Security Settings

Wireless Repeater

DIR-608

Wireless

Advanc

Step 2: The page will refresh prompting you to input the wireless security key of the host

network. If the host network does not have wireless security enabled, this step is omitted.

Step 3: Enter a new LAN IP address for the DIR-608 if necessary.

Click

Finish

to complete the setup. You will need to reconnect to the wireless network the

DIR-608 is now repeating.

Wireless Repeater Setup (continued)

Wireless Security Settings

Enryption:

WPA2-PSK(TKIP)

▼

Security Options

Security Options:

The host network’s wireless security encryption type is listed here. It

is not changeable.

Security Options(WPA-PSK)

Pre-Shared Key:

(8-63 characters or 64 hex digits)

Security Options(WPA2-PSK)

Pre-Shared Key:

Enter the host network’s wireless security key.

When you have entered the wireless network’s key, click the

Next

button.

Previous

Next

WPS Setup

Step 3: click ‘Finish’ to save the configuration.

We strongly recommend that you modify IP address of the

local gateway to avoid IP address conflicts with the center

of the AP. (ex. if IP address of AP is 192.168.1.1, you can

modify IP address of the local gateway to 192.168.1.2)

IP Address:

192.168.11.1

Subnet Mask:

255.255.255.0

Finish

60

D-Link DIR-608 User Manual

Section 3 - Configuration

Advanced

The Advanced tab provides access to configure the advanced features of your DIR-608.

Product Page: DIR-608

Hardware version:A1

Firmware version: 1.00

English

Select Language

▼

DIR-608

Setup

Wireless

Advanced

Maintenance

Status

Help

Access Control List

Port Triggering

DMZ

URL Block

Dynamic DNS

Traffic Control

UPnP

Telnet

Virtual Server

IPv6 Filter

IPv6 Routing

To return to the Web UI Table of Contents page, simply click the D-Link logo on the top right

of each page.

Wizard

DIR-608

Setup

Wirele

61

D-Link DIR-608 User Manual

Section 3 - Configuration

Access Control List

Current ACL Table

The section displays the current ACL Table.

ACL Settings

WAN Setting:

Use the dropdown menu to select either WAN or IP Address.

IP Address:

This option will only be seen if you have selected IP Address above.

Enter the IP address range.

Services Allowed:

Select the type of Internet service from which packets can be allowed

into the network.

Click the

Add

button to save and add these settings to the Current ACL table.

WAN ACL Configuration

Access Control List

DIR-608

Advanced

Mainten

ACL Settings

WAN Setting:

WAN

▼

Services Allowed:

☐

web

☐

ping

ACL Settings

WAN Setting:

IP Address

▼

IP Address:

-

(0.0.0.0 represents any IP)

Services Allowed:

☐

web

☐

ping

Add

Reset

Current ACL Table

Select

IP Address

/Interface

Service

Port

Action

1

WAN

web

80

Delete

This page allows you to set up an Access Control List to restrict the types of data packets

that can enter the network from the Internet.