Page 116 / 145 Scroll up to view Page 111 - 115
116
Step 11
Select 1 out of the Proposal
ID dropdown menu and click Add To,
which will add the proposal that was just
configured to the IKE Proposal Index.
Click Apply and then click Back.
How can I set up my router to work with a DI-804V router? (continued)
Frequently Asked Questions (continued)
Step 12
Click on Select IPSec
Proposal...
Step 13
Enter a name for proposal ID
number 1 and select None from the DH
Group dropdown menu.
Step 14
Select ESP as the
Encapsulation Protocol.
Step 15
Select 3DES as the Encryption Algorithm and MD5 as the Authentication
Algorithm.
Step 16
Enter a Lifetime value of 3600
and then select Sec. as the unit for the
lifetime value.
Page 117 / 145
117
How can I set up my router to work with a DI-804V router? (continued)
Frequently Asked Questions (continued)
Step 17
Select 1 out of the Proposal
ID dropdown menu and click Add To,
which will add the proposal that was just
configured to the IPSec Proposal Index.
Click Apply and then click Restart.
Next you need to configure the DI-804V router.
Step 1
Access the router’s web configuration by entering the router’s IP address in
your web browser. The default IP address is 192.168.0.1. Login using your password.
The default username is “admin” and the password is blank.
Step 2
Click on Basic Setup and then select Device IP Settings on the left.
Step 3
Change the LAN IP address so
that it is on a different subnet than the
LAN of the DI-804HV.
Step 4
Click Next until you reach the
Save & Restart screen. Click Save &
Restart and then click Basic Setup once
the unit has rebooted.
Step 5
Click on VPN Settings.
Page 118 / 145
118
How can I set up my router to work with a DI-804V router? (continued)
Frequently Asked Questions (continued)
Step 6
Name your VPN connection and
click ADD.
Step 7
In Remote IP Network and Remote
IP Netmask fields enter the network
identifier and corresponding subnet mask
of the DI-804HV´s LAN.
Step 8
In the Remote Gateway IP field
enter the WAN IP address of the DI-804HV
and make sure that the Network Interface
is set to WAN Ethernet.
Step 9
Verify that Secure Association is set to IKE and that Perfect Forward Secure is
Disabled.
Step 10
Verify the Encryption Protocol
is set to 3DES and enter in your Preshared
Key.
Note: The Preshared Key needs to be
identical to the one configured on the
DI-804HV.
Step 11
Leave the Key Life and IKE Life
Time values at their default levels and click
SAVE.
Step 12
Click Next and then click on Save
& Restart
Page 119 / 145
119
How can I set up my router to work with a DI-804V router? (continued)
Frequently Asked Questions (continued)
After you have configured both routers, you need to establish a connection.
Step 5
When the VPN has been
established the Status will be Active.
Step 1
Open a command prompt and
from a computer on the internal LAN of
the DI-804HV and ping the IP address of
a computer that is on the internal LAN
of the DI-804V, or vice versa.
Step 2
Once you begin to receive
replies, the VPN connection has been
established.
Step 3
To view the Status of the VPN
on the DI-804V, click on Device Status.
Step 4
From the Device Status screen
click on VPN Status.
How can I set up my router to work with a DFL-300 firewall?
You need to first configure your DI-804HV router.
Step 1
Log into the web based configuration of the router by typing in the IP address of
the router (default: 192.168.0.1) in your web browser. By default the username is “admin”
and there is no password.
Step 2
Click the VPN button on the left column, select the checkbox to Enable the
VPN, and then in the box next to Max. number of tunnels, enter the maximum numbers
of VPN tunnels that you would like to have connected.
Page 120 / 145
120
How can I set up my router to work with a DFL-300 firewall?
(continued)
Frequently Asked Questions (continued)
Step 3
In the space provided, enter the
Tunnel Name for ID number 1, select IKE,
and then click More.
Step 4
In the Local Subnet and Local
Netmask fields enter the network
identifier for DI-804HV´s LAN and the
corresponding subnet mask.
Step 5
In the Remote Subnet and
Remote Netmask fields enter the
network identifier for the DFL-300´s
Internal interface and the corresponding
subnet mask.

Rate

4.5 / 5 based on 2 votes.

Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top