Page 106 / 145 Scroll up to view Page 101 - 105
106
Frequently Asked Questions (continued)
How can I setup my router to work with Earthlink DSL or any PPPoE
connection?
Make sure you disable or uninstall any PPPoE software such as WinPoet or Enternet
300 from your computer or you will not be able to connect to the Internet.
Step 1
Upgrade Firmware if needed.
(Please visit the D-Link tech support website at:
for the latest
firmware upgrade information.)
Step 2
Take a paperclip and perform a hard reset. With the unit on, use a paperclip
and hold down the reset button on the back of the unit for 10 seconds. Release it and
the router will recycle, the lights will blink, and then stabilize.
Step 3
After the router stabilizes, open your browser and enter 192.168.0.1 into the
address window and hit the
Enter
key. When the password dialog box appears, enter
the username
admin
and leave the password blank. Click
OK
.
If the password dialog box does not come up repeat
Step 2
.
Note:
Do not run Wizard.
Step 4
Click on the
WAN
tab on left-hand side of the screen. Select
PPPoE
.
Step 5
Select
Dynamic PPPoE
(unless your ISP supplied you with a static IP
Address).
Step 6
In the username field enter
and your
password, where username is your own username.
For SBC Global users, enter
.
For Ameritech users, enter
.
For BellSouth users, enter
.
For Mindspring users, enter
For most other ISPs, enter
username
.
Step 7
Maximum Idle Time
should be set to zero. Set
MTU
to 1492, unless
specified by your ISP, and set
Autoreconnect
to
Enabled
.
Note:
If you experience problems accessing certain websites and/or email issues,
please set the MTU to a lower number such as 1472, 1452, etc. Contact your ISP for
more information and the proper MTU setting for your connection.
Page 107 / 145
107
Step 8
Click
Apply
. When prompted, click
Continue
. Once the screen refreshes,
unplug the power to the D-Link router.
Step 9
Turn off your DSL modem for 2-3 minutes. Turn back on. Once the modem
has established a link to your ISP, plug the power back into the D-Link router. Wait
about 30 seconds and log back into the router.
Step 10
Click on the
Status
tab in the web configuration where you can view the
device info. Under
WAN
, click
Connect
. Click
Continue
when prompted. You should
now see that the device info will show an IP Address, verifying that the device has
connected to a server and has been assigned an IP Address.
How can I setup my router to work with Earthlink DSL or any PPPoE
connection? (continued)
Frequently Asked Questions (continued)
Can I use my D-Link Broadband Router to share my Internet
connection provided by AOL DSL Plus?
In most cases yes. AOL DSL+ may use PPPoE for authentication bypassing the
client software. If this is the case, then our routers will work with this service. Please
contact AOL if you are not sure.
To set up your router:
Step 1
Log into the web-based configuration (192.168.0.1) and configure the WAN
side to use PPPoE.
Step 2
Enter your screen name followed by @aol.com for the user name. Enter your
AOL password in the password box.
Step 3
You will have to set the MTU to 1400. AOL DSL does not allow for anything
higher than 1400.
Step 4
Apply settings.
Step 5
Recycle the power to the modem for 1 minute and then recycle power to the
router. Allow 1 to 2 minutes to connect.
If you connect to the Internet with a different internet service provider and want to use
the AOL software, you can do that without configuring the router’s firewall settings.
You need to configure the AOL software to connect using TCP/IP.
Go to
for more specific configuration information of their software.
Page 108 / 145
108
Step 1
Log into the web based
configuration of the router by typing in
the IP address of the router (default:
192.168.0.1) in your web browser.
By
default the username is “admin” and
there is no password.
How can I set up my router to work with another DI-804HV router?
Frequently Asked Questions (continued)
Step 2
Click the VPN button on the left
column, select the checkbox to Enable
the VPN, and then in the box next to Max.
number of tunnels, enter the maximum
numbers of VPN tunnels that you would
like to have connected.
Step 3
In the space provided, enter the
Tunnel Name for ID number 1, select IKE,
and then click More.
Page 109 / 145
109
How can I set up my router to work with another DI-804HV router?
(continued)
Frequently Asked Questions (continued)
Step 4
In the Local Subnet and Local
Netmask fields enter the network
identifier for the local DI-804HV´s LAN
and the corresponding subnet mask.
Step 5
In the Remote Subnet and
Remote Netmask fields enter the
network identifier for the remote DI-
804HV´s LAN and the corresponding
subnet mask.
Step 6
In the Remote Gateway field
enter the WAN IP address of the remote
DI-804HV and in the Preshared Key field,
enter a key which must be exactly the
same as the Preshared Key that is
configured on the remote DI-804HV.
Step 7
Click Apply and then click on
Select IKE Proposal...
Page 110 / 145
110
How can I set up my router to work with another DI-804HV router?
(continued)
Frequently Asked Questions (continued)
Step 8
Enter a name for proposal ID
number 1 and select Group 1, 2, or 5
from the DH Group dropdown menu.
Step 9
Select DES or 3DES as the
Encryption Algorithm and either SHA-1
or MD5 as the Authentication Algorithm.
Step 10
Enter a Lifetime value and then
either select Sec. or KByte as the unit
for the lifetime value.

Rate

4.5 / 5 based on 2 votes.

Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top