Page 136 / 145 Scroll up to view Page 131 - 135
136
Frequently Asked Questions (continued)
How do I configure my router to play
Warcraft 3?
You must open ports on your router to allow incoming traffic while
hosting a game in
Warcraft 3. To play a game, you do not have to configure your router.
Warcraft 3 (Battlenet) uses port 6112.
For the DI804HV:
Step 1
Open your web browser and
enter the IP Address of your router
(192.168.0.1). Enter username (admin)
and your password (leave blank).
Step 2
Click on
Advanced
and then
click
Virtual Server
.
Step 3
Create a new entry: Click
Enabled
. Enter a name (warcraft3).
Private IP - Enter the IP Address of the
computer you want to host the game.
Select
Both
for Protocol Type Enter
6112
for both Private Port and Public Port Click
Always
or set a schedule.
Step 4
Click
Apply
and then
Continue
.
Note:
If you want multiple computers from you LAN to play in the same game that
you are hosting, then repeat the steps above and enter the IP Addresses of the other
computers. You will need to change ports. Computer #2 can use port 6113, computer
#3 can use 6114, and so on.
You will need to change the port information within the Warcraft 3 software for
computers #2 and up.
Configure the Game Port information on each computer:
Start Warcraft 3 on each computer, click
Options
>
Gameplay
. Scroll down and you
should see
Game Port
. Enter the port number as you entered in the above steps.
warcraft3
100
6500
6500
Both
Page 137 / 145
137
Frequently Asked Questions (continued)
How do I use NetMeeting with my D-Link Router?
Unlike most TCP/IP applications, NetMeeting uses
DYNAMIC PORTS
instead of
STATIC PORTS. That means that each NetMeeting connection is somewhat different
than the last. For instance, the HTTP web site application uses port 80. NetMeeting
can use any of over 60,000 different ports.
All broadband routers using (only) standard NAT and all internet sharing programs like
Microsoft ICS that use (only) standard NAT will NOT work with NetMeeting or other
h.323 software packages.
The solution is to put the router in DMZ.
Note:
A few hardware manufacturers have taken it on themselves to actually provide
H.323 compatibility. This is not an easy task since the router must search each
incoming packet for signs that it might be a netmeeting packet. This is a whole lot
more work than a router normally does and may actually be a
weak point in the
firewall
. D-Link is not one of the manufacturers.
To read more on this visit
http://www
.HomenetHelp.com
How do I set up my router to use iChat?
-for Macintosh users-
You must open ports on your router to allow incoming traffic while using iChat.
iChat uses the following ports: 5060 (UDP) 5190 (TCP) File Sharing 16384-16403
(UDP) To video conference with other clients
Step 1
Open your web browser and enter the IP Address of your router
(192.168.0.1). Enter username (admin) and your password (leave blank).
Step 2
Click on
Advanced
and then click
Firewall
.
Page 138 / 145
138
Frequently Asked Questions (continued)
Step 3
Create a new firewall
rule:
Leave the second box empty. Under
Protocol, select
UDP
. In the port range boxes,
enter
5060
in the first box and leave the second box empty.
Click
Always
or set a schedule.
Step 4
Click
Apply
and then
Continue
.
Step 5
Repeat steps 3 and 4 enter
ichat2
and open ports
16384-
16403
(UDP).
How do I set up my router to use iChat? -for Macintosh users-
(continued)
Click
Enabled
.
Enter a name (ichat1).
Click
Allow
.
Next to Source, select
WAN
under interface.
In the first box, enter an
*
.
Leave the second box
empty.
Next to Destination, select
LAN
under interface.
Enter the IP Address of the
computer you are running
iChat from.
ichat1
WAN
LAN
192.168.0.100
UDP
5060
ichat2
WAN
LAN
192.168.0.100
UDP
1638
1640
Page 139 / 145
139
Frequently Asked Questions (continued)
If using Mac OS X Firewall, you may need to temporarily turn off the firewall in
the Sharing preference pane on both computers.
To use the Mac OS X Firewall, you must open the same ports as in the router:
Step 1
Choose
Apple menu
>
System Preferences
.
Step 2
Choose
View
>
Sharing
.
Step 3
Click the
Firewall
tab.
Step 4
Click
New
.
Step 5
Choose
Other
from the Port Name pop-up menu.
Step 6
In the Port Number, Range or Series field, type in:
5060
,
16384-16403
.
Step 7
In the Description field type in:
iChat AV
Step 8
Click
OK
.
For File Sharing:
Step 1
Click on
Advanced
and
then
Virtual Server
.
Step 2
Check
Enabled
to
activate entry.
Step 3
Enter a name for your
virtual server entry (ichat3).
Step 4
Next to Private IP, enter
the IP Address of the computer on
your local network that you want
to allow the incoming service to.
Step 5
Select
TCP
for Protocol
Type.
Step 6
Enter
5190
next to Private
Port and Public Port.
Stsp 7
Click
Always
or configure a schedule.
Step 8
Click
Apply
and then
Continue
.
How do I set up my router to use iChat? -for Macintosh users-
ichat3
100
6500
6500
Page 140 / 145
140
Frequently Asked Questions (continued)
How do I send or receive a file via iChat when the Mac OSX firewall
is active? -for Macintosh users- Mac OS X 10.2 and later
“iChat cannot send or receive a file when the Mac OS X firewall is active in its default
state. If you have opened the AIM port, you may be able to receive a file but not send
them.
In its default state, the Mac OS X firewall blocks file transfers using iChat or America
Online AIM software. If either the sender or receiver has turned on the Mac OS X firewall,
the transfer may be blocked.
The simplest workaround is to temporarily turn off the firewall in the Sharing preference
pane on both computers. This is required for the sender. However, the receiver may keep
the firewall on if the AIM port is open. To open the AIM port:
If you do not want to turn off the firewall at the sending computer, a different file sharing
service may be used instead of iChat. The types of file sharing available in Mac OS X are
outlined in technical document 106461, "Mac OS X: File Sharing" in the
AppleCare Knowl-
edge base
online.
Note: If you use a file sharing service when the firewall is turned on, be sure to click the
Firewall tab and select the service you have chosen in the "Allow" list. If you do not do
this, the firewall will also block the file sharing service. “
The following information is from the online Macintosh AppleCare knowledge base:
Step 1
Choose Apple menu > System Preferences.
Step 2
Choose View > Sharing.
Step 3
Click the Firewall tab.
Step 4
Click New.
Step 5
Choose AOL IM from the Port Name pop-up menu. The number 5190
should already be filled in for you.
Step 6
Click OK.

Rate

4.5 / 5 based on 2 votes.

Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top