1. Home
    2. /
  2. Manuals
    3. /
  3. D-Link
    4. /
  4. DCS-5610
    5. /
  5. 7
Page 31 / 80 Scroll up to view Page 26 - 30
²1
D-Link DCS-5610 User Manual
Section ² - Configuration
Click
Apply
You have completed the Motion Detection Wizard. Click
Apply
to save your settings.
Page 32 / 80
²±
D-Link DCS-5610 User Manual
Section ² - Configuration
LAN Settings:
DHCP:
Static IP Client:
IP Address:
Subnet Mask:
Default Gateway:
Primary DNS:
Secondary DNS:
Enable UPnP
Presentation:
Enable UPnP Port
Forwarding:
PPPoE Settings:
Settings for your local area network.
Select this connection if you have a DHCP server running on your network
and would like a dynamic IP address to be updated to your camera
automatically.
You may obtain a static or fixed IP address and other network information
from your network administrator for your camera. A static IP address will
ease you for accessing your camera in the future.
The fixed IP address.
The default value is “255.255.255.0.” Used to determine if the destination
is in the same subnet.
The gateway used to forward frames to destinations in a different subnet.
Invalid gateway settings may cause the failure of transmissions to a
different subnet.
Primary domain name server that translates names to IP addresses.
Secondary domain name server to backup the primary one.
Allows a user to find, view and control this camera via a presentation page
or “Network Neighborhood” without configuration.
Enables the camera to add the port forwarding entry into the router
automatically when this option is enabled.
Enable this setting if your ISP (DSL service) is using PPPoE. You may
already have both
Username
and
Password
given by your ISP, or you may
check with your ISP. The
Connect Status
will be determined automatically
by the system.
Network Setup
Page 33 / 80
²²
D-Link DCS-5610 User Manual
Section ² - Configuration
HTTP:
Authentication:
HTTP Port:
Secondary HTTP
Port:
Access name for
stream1:
Access name for
stream2:
FTP Port:
RTSP Streaming:
Authentication:
Access name for
stream1:
Access name for
stream2:
You may configure two HTTP ports for your camera. HTTP ports allow you to connect to the camera via a standard web browser.
These ports can be set to a number other than the default TCP ports 80 and 8080. A corresponding port must be opened
on the router. For example, if the port is changed to 1010, users must type in the web browser “http://192.168.0.100:1010”
Authentication
: Choose either
Basic
where the password is not encrypted, or
Digest
where the password is encrypted
during the transmission to the web server.
The default value is 80.
The default value is 8080.
After you have enabled the
Authentication
, you will need to configure and use the access name to access your video file.
For example,
http://camera ip/video.mjpg
(video.mjpg is the
Access name
, you can modify it here)
The default name is video.mjpg.
The default name is video2.mjpg.
Default port is 21. If you want to change the port number, you will need to specify the port when connecting to the FTP server.
For example FTP://68.5.1.81:60 (if you use port 60 for your FTP server)
This setting enables you to connect to a camera by using streaming mobile device(s), such as a mobile phone or PDA.
Choose either
Basic
where the password is not encrypted, or
Digest
where the password is encrypted during the transmission
to the web server. After you have enabled the
Authentication
, you will need to configure and use the access name to access
your video file.
RTSP://camera ip/live.sdp
(live.sdp is the default access name, you can modify it here)
The default name is live.sdp.
The default name is live2.sdp.
Page 34 / 80
²³
D-Link DCS-5610 User Manual
Section ² - Configuration
RTSP port:
RTP port for video:
RTCP port for video:
RTP port for audio:
RTCP port for audio:
Multicast group
address:
Multicast video port:
Multicast RTCP video
port:
Multicast audio port:
Multicast RTCP audio
port:
Multicast TTL
{1~255]:
The port number that you use for RSTP streaming, the default port number is 554.
RTP
(Real Time Protocol)
Port
is used
to streaming audio and video while
RTCP
(Real Time Control Protocol) port is used to monitor QoS of RTP stream.
Note:
RTP video port and RTP audio port must be an “even” number. The numbers of RTCP video port and RTCP audio
port must equal to the numbers of RTP video port and RTP audio port, plus one repetitively
Default port number is 5556.
Default port number is 5557.
Default port number is 5558.
Default port number is 5559.
You may choose to enable multicast for your camera audio and video streaming so that your
cameras (sources)
and the
receivers (clients)
can establish the connection to send and receive contents.
An IP Multicast group address is used to send and receive content. Sources use this group address as the destination
address while sending their data packets. Receivers use this group address to inform the network that they are interested
in receiving packets sent to that group.
For example, if some content is associated with group 239.1.1.1, the source will send data packets destined to 239.1.1.1.
Receivers for that content will inform the network that they are interested in receiving data packets sent to the group
239.1.1.1. The receiver “joins” 239.1.1.1. The Multicast address ranges from 224.0.0.0 to 239.255.255.255, or, equivalently,
224.0.0.0/4
Default port number is 5560, or please choose between 1024 and 65534.
Default port number is 5561, or please choose between 1024 and 65534.
Default port number is 5562, or please choose between 1024 and 65534.
Default port number is 5563, or please choose between 1024 and 65534.
Set a Time to Live(TTL) value for multicast packet, please choose between 1 and 255.
Page 35 / 80
²5
D-Link DCS-5610 User Manual
Section ² - Configuration
Enable DDNS:
Server Name:
Host Name:
Username:
Password:
Status:
Click to enable the DDNS function.
Select your Dynamic DNS provider from the pull
down menu.
Enter the host name of the DDNS server.
Enter your username or e-mail used to connect
to the DDNS
Enter your password used to connect to the DDNS
server.
Indicate the connection status, automatically
determined by the system.
Dynamic DNS
DDNS (Dynamic Domain Name Server) will hold a DNS host name and synchronize the public IP address of the modem
when it has been modified. The username and password are required when using the DDNS service.

Rate

4 / 5 based on 1 vote.

Popular D-Link Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top