1. Home
    2. /
  2. Manuals
    3. /
  3. D-Link
    4. /
  4. DCS-5610
    5. /
  5. 10
Page 46 / 80 Scroll up to view Page 41 - 45
³6
D-Link DCS-5610 User Manual
Section ² - Configuration
Recording entry
name:
Enable this
recording:
Priority:
Source:
Recording schedule:
Recording settings:
Destination:
Total cycling
recording size:
Size of each file for
recording:
File Name Prefix:
The unique name of the entry.
Select this to enable the recording function.
Set the priority for this entry and the entry with
higher priority will be executed first.
The source of stream.
Scheduling the recording entry.
Configuring the setting for the recording.
Select the folder where will store the recording
file.
Please input a HDD memory volume between
1MB and 200GB for recording space. The
recording data will replace the oldest one when
total recording size exceeds this value. For
example, if each recording file is 6MB, and the
total cycling recording size is 600MB, then camera will recording 100 files to the specified location (folder). And then the
camera will delete the oldest file and create new file for cycling recording.
Please notice that if the HDD empty space is not enough, the recording will stop. Before you setup this option please make
sure you HDD have enough space and it is better not to save other files in the same folder as recording files.
File size for each recording file. You may input the value in the range of 200-6000.
The prefix name will be added on the file name of the recording file(s).
Add Recording
You can add and configure an entry here.
Page 47 / 80
³´
D-Link DCS-5610 User Manual
Section ² - Configuration
Up, Down, Left,
Right, Home:
Zoom (-):
Zoom (+):
Pan Speed:
Tilt Speed:
Zoom Speed:
Auto pan/patrol
speed:
Dwelling time (sec):
Preset locations:
Selected locations:
“
Home
” aims the camera to the center,
where as the other buttons aim the camera
accordingly.
Zoom widely function.
Zoom telescopically function
Select the speed at which the camera will
pan for a full cycle from the pull down menu.
Select a value between -5 and +5, -5 being
the slowest setting.
Select the speed at which the camera will
tilt for a full cycle from the pull down menu.
Select a value between -5 and +5, -5 being
the slowest setting.
Select the speed at which the camera will
zoom for a full cycle from the pull down menu.
Select a value between -5 and +5, -5 being
the slowest setting.
Select the speed at which the camera will pan
during auto patrol. Select a value between 1
and 5, 1 being the slowest setting.
Set the value of time that the camera will remain on each preset position before moving to the next. The dwelling time
can be set between 1 and 255 seconds.
Desired positions that have been configured.
To use the Auto Patrol feature, select the desired preset positions from the
Preset Locations
list and add them to the
Selected Locations
list by clicking Select. You can then select the order in which the camera will patrol through the preset
locations by selecting a location and clicking
UP
or
DN
. Click
Remove
to remove a location from the list.
Camera Control
Here you can preset the locations and change the default location for your home button.
Page 48 / 80
³µ
D-Link DCS-5610 User Manual
Section ² - Configuration
Enter a name for the position at which you would like to preset the
DCS-5610
. Click
Add
to add the new preset position to
the
Preset Locations
list.
A pull-down menu that contains all the preset locations. You can delete a preset position by selecting it and clicking
Delete
.
Allow users to set a new home position or default back to the original.
Current
Position:
Preset
Position:
Home
Location:
Page 49 / 80
³¶
D-Link DCS-5610 User Manual
Section ² - Configuration
Allow list:
Start IP address:
End IP address:
Delete allow list:
Deny list:
Delete deny list:
The list of IP addresses that have the access right
to the camera.
The starting IP Address of the devices (such as
a computer) that have permission to access the
video of the camera.
The ending IP Address of the devices (such as
a computer) that have permission to access the
video of the camera.
Remove the customized setting from the Allow
List.
The list of IP addresses that have no access right
to the camera.
Remove the customized setting from the Delete
List.
Access List
Here you can configure the access permissions for each user.
Page 50 / 80
50
D-Link DCS-5610 User Manual
Section ² - Configuration
DI and DO:
Digital input trigger
condition:
Digital output:
Setting for both Digital input signal and digital
output signal can be configured here.
Please select from “
High
” or “
Low
” for digital input
trigger condition. When external device connect to
the digital input pins, the state of the voltage will
be monitored. (Max. Input 500mA, 12Vdc)
Select
Grounded
or
Open
to define normal status
of the digital output. The camera will show whether
the trigger is activated or not.
DI and DO
The I/O connector provides the physical interface for digital output (DO) and digital input (DI) that is used for connecting
such external alarm devices as IR-Sensors and alarm relays to the PTZ IP camera.

Rate

4 / 5 based on 1 vote.

Popular D-Link Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top