D-Link DCS-1130 Router Manual PDF (Setup & Configuration Guide)

Page 21 / 50 Scroll up to view Page 16 - 20

17

D-Link DCS-1130 User Manual

Section 3 - Conﬁguration

Site survey:

Click the

Rescan

button to scan for available wireless

networks. After scanning, you can use the dropdown box to select an

available wireless network. The related information (SSID, Wireless

Mode, Channel, Authentication, Encryption) will be automatically ﬁlled

in for you.

SSID:

The SSID of the wireless access point you wish to use.

Wireless Mode:

Use the dropdown box to select the mode of the wireless

network you wish to connect to.

Infrastructure

is normally used to connect

to an access point or router.

Ad-Hoc

is usually used to connect directly

to another computer.

Channel:

If you are using Ad Hoc mode, select the channel of the wireless

network you wish to connect to, or select

Auto

.

Authentication:

Select the authentication you use on your wireless network -

Open

,

Shared (WEP)

,

WPA-PSK

, or

WPA2-PSK

.

Encryption:

If you use

WPA-PSK

or

WPA2-PSK

authentication, you will need to specify whether your wireless

network uses TKIP or AES encryption. If you use

Open

or

Shared

authentication, this setting will be automatically set

for you.

Key:

If you use

WEP, WPA-PSK

, or

WPA2-PSK

authentication, enter the

Key

(also known as password) used for

your wireless network.

After making any changes, click the

Save Settings

button to save your changes, or click the

Don’t Save Settings

button to discard your changes.

Setup > Wireless

To set up your IP camera’s wireless network interface settings, enable

Wireless Settings

in this window ﬁrst, then

enter the required settings.

Page 22 / 50

18

D-Link DCS-1130 User Manual

Section 3 - Conﬁguration

If you have a DSL or Cable service provider that changes your modem IP

address periodically, Dynamic DNS (Domain Name Service), a method

of keeping a domain name linked to a dynamic IP address, is useful.

With most Cable and DSL connections, you are assigned a dynamic IP

address and that address is used only for the duration of that speciﬁc

connection. With the DCS-1130, you can set up your DDNS service and

the DCS-1130 will automatically update your DDNS server every time it

receives a different IP address. Depending on the service, this update

may take a few hours.

Enable DDNS:

Check this checkbox to enable the DDNS function of the

camera.

Server Address:

Use the dropdown box on the right to select a DDNS

service.

Host Name:

Type in the Host Name of the DDNS service.

User Name:

Enter your User Name for the DDNS service.

Password:

Enter the password for the DDNS service.

Verify Password:

Retype the password for the DDNS service.

Timeout:

This sets the number of hours between DDNS updates.

After making any changes, click the

Save Settings

button to save your changes, or click the

Don’t Save Settings

button to discard your changes.

Setup > Dynamic DNS

Page 23 / 50

19

D-Link DCS-1130 User Manual

Section 3 - Conﬁguration

The options in

Image Setup

allow you to adjust the settings for your IP

camera sensor and image.

Brightness

: This adjusts the brightness of the camera image. This is set

to 60 by default.

Saturation

: This adjusts the color saturation of the camera image. This

is set to 60 by default.

Contrast

: This adjusts the contrast of the camera image. This is set to

0 by default.

Frequency

: This option adjusts the camera sensor’s setting to avoid the

image ﬂickering under certain light sources, such as ﬂorescent lights. This

is set to

60Hz

by default.

White balance

: You can change the white balance of the camera image

by selecting a setting from the dropdown box. This is set to

Auto

by

default.

B/W

: Ticking this checkbox will change the camera image into black and

white.

Flip

: This will ﬂip the image vertically.

Mirror

: This will ﬂip the image horizontally in such a way that your left side will be on the left side of the screen and

vice versa.

Note

:

Mirror

and

Flip

can be used if you choose to mount the DCS-1130 upside down on the ceiling.

Setup > Image Setup

Page 24 / 50

20

D-Link DCS-1130 User Manual

Section 3 - Conﬁguration

Setup > Audio and Video

Encode Type

: This sets the video codec used for the video stream. You

can choose MPEG-4 or MJPEG (JPEG). Internet Explorer browsers can

view both MPEG-4 and MJPEG video streams, and non-IE browsers can

only view MJPEG video streams.

Resolution

: This sets the display resolution of the video stream. If the

Resolution is different than the Sensor Output size, the video will be

shrunken or enlarged to the Resolution size you set here.

FPS

: This sets the target number of frames per second (FPS) for the

video stream. Higher frame rates will provide smoother video.

bps

: This sets the target bitrate of the video stream. Higher bitrates will

provide better quality video. When the Encode Type is set to MJPEG, you

cannot change the bps setting. Also, available bps settings may change

depending on what the Encode Type, Sensor Output, Resolution, and

FPS settings are set to.

JPEG Quality

: This sets the JPEG quality of any manual snapshots you take when this video proﬁle is selected

RTSP URL

: This setting allows you to set a sufﬁx for your camera’s RTSP URL so you can view your camera’s video

with this video proﬁle’s settings. For example, if you enter “mpeg4” as your RTSP URL setting and your camera’s IP

is 192.160.0.20, you can view your camera’s video with these settings through 192.160.0.20/mpeg4.

You may conﬁgure four video proﬁles with different settings for your camera. You may also set up different proﬁles for

your computer and mobile display. In addition, you may conﬁgure the audio (speakers and microphone) settings for

your camera.

Page 25 / 50

21

D-Link DCS-1130 User Manual

Section 3 - Conﬁguration

Note

: Video Proﬁle 3 is always set to MJPEG as the Encode Type to

ensure that at least one of the Video Proﬁles are viewable by non-IE

browsers. Video Proﬁle 4 is for mobile devices only, and always uses

MPEG-4 as the Encode Type.

Enable Night Mode

: Check this box to enable Night Mode. Night mode

allows the camera to use a longer shutter speed when the camera is in a

low-light environment. If the camera is in an area where there is sufﬁcient

lighting, Night Mode will not affect the video stream.

Shutter

: This sets the longest shutter speed Night Mode will use when

Night Mode is enabled and the camera is viewing a low-light scene.

Light Source

: Here you can set the kind of lighting used in the area your

camera is monitoring to improve the image quality of the video.

Enable Microphone

: Checking this box will enable you to listen to audio

picked up by the camera’s microphone. This will allow you to hear what

is happening near your camera.

Volume

: This sets the volume level of the incoming audio.

Note

: Higher frame size, frame rate and bit rates will give you better video

quality, but they will also require more network bandwidth. For best viewing

results on a mobile phone, we suggest setting the frame rate to 5 fps and

bit rate to 20 Kbps.

After making any changes, click the

Save Settings

button to save

your changes, or click the

Don’t Save Settings

button to discard your

changes.

Rate

Popular D-Link Models

Famous Router IPs

Famous Router Companies

Bookmark Our Site

Share