DG-BR4000NG User Manual

61

After you finish with all settings, please click ‘Apply’ button and the following

message will be displayed on your web browser:

If you want to reset all settings in this page back to previously-saved value, please

click ‘Cancel’ button.

Please click ‘Continue’ to go back to previous setup menu; to continue on other

setup procedures, or click ‘Apply’ to reboot the router so the settings will take effect

(Please wait for about 30 seconds while router is rebooting).

DG-BR4000NG User Manual

62

2-5-7 Setup procedure for ‘DDNS’:

DDNS (Dynamic DNS) is an IP-to-Hostname mapping service for those Internet

users who don’t have a static (fixed) IP address. It will be a problem when such

users want to provide services to other users on Internet, because their IP address

will vary every time when connected to Internet. Thus other users will not be able to

know the IP address they’re using at a certain time.

This router supports DDNS service of several service providers, for example:

DynDNS (

)

TZO (

)

Please go to one of DDNS service provider’s webpage listed above, and get a free

DDNS account by the instructions given on their webpage.

Here is the description of every setup item:

Parameter

Description

Dynamic DNS

If you want to enable DDNS function,

please select ‘Enabled’; otherwise please

select ‘Disabled’.

Provider

Select your DDNS service provider here.

Domain Name

Input the domain name you’ve obtained

from DDNS service provider.

Account

Input

username

used

for

DDNS

registration.

Password / Key

Input DDNS service password or key.

DG-BR4000NG User Manual

63

After you finish with all settings, please click ‘Apply’ button and the following

message will be displayed on your web browser:

If you want to reset all settings in this page back to previously-saved value, please

click ‘Cancel’ button

Please click ‘Continue’ to go back to previous setup menu; to continue on other

setup procedures, or click ‘Apply’ to reboot the router so the settings will take effect

(Please wait for about 30 seconds while router is rebooting).

DG-BR4000NG User Manual

64

2-5-8 Setup procedure for ‘WISP’

WISP (Wireless Internet Service Provider) is the service provided by your service

provider through a wireless network.

If your network service provided by your service provider is through wireless

network, please select this mode. After you have connected the router to the access

point of service provider wirelessly, please setup the WAN connection type in WAN

page. By default ‘WISP’ is disabled. If you want to enable ‘WISP’ click the ‘Enable’

button and the screenshot as shown below will appear.

Here is the description of every setup item:

Parameter

Description

Disable/Enable/ staEnable

There are three options mentioned

below:

Disable: Disable this function.

Enable: Enable this function and the

router can connect to the access points

installed

by

your

wireless

service

provider. Any clients associated to the

router can access the Internet service

through the wireless network.

Note: In this mode, if you are informed

DG-BR4000NG User Manual

65

by your wireless ISP that the wireless

settings of the access point is changed,

please configure the router in this page

to match the settings.

staEnable: Enable this function and the

router can only allow to be connected

through wired Ethernet cable for WAN

access service.

SSID

This is the name of the wireless network.

Input the SSID name that your wireless

ISP has provided you with.

Channel Number

This is the radio frequency used to

transmit and receive the wireless signal.

The

wireless

devices

in

the

same

network should follow the same setting.

Select the channel designated by your

wireless ISP.

Site Survey

Click ‘Select Site Survey’ button, then a

“Wireless Site Survey Table” will pop

up. It will list all available access points

nearby.

Select

the

access

point

designated by your wireless ISP in the

table and the router will join wireless

network through this access point.

Security Setting

If the access point enables wireless

security, you have to follow the same

settings in order to access the access

point. Click to set security settings for

this connection (Please go to section

‘2-

7-3 Wireless Security’

for detailed

instructions).

MAC

If your service provider binds your

internet connection with a specific MAC

address then enter a MAC address in the

format 010203040506.

Clone MAC

Click this button if you want to clone the

WAN port MAC address of the router

with that of the PC.